HomeMy WebLinkAbout19-22158 CITY OF ZEPHYRHILLS
5335-8TH STREET
(813)780-0020 22158
BUILDING PERMIT
PERMIT INFORMATION LOCATION INFORMATION
Permit Number: 22158 Address: 6420 LAURELWOOD DR
Permit Type: RE-ROOF ZEPHYRHILLS, FL.
Class of Work: ROOF REPLACEMENT Township: Range: Book:
Proposed Use: NOT APPLICABLE Lot(s): Block: Section:
Square Feet: Subdivision: SILVER OAKS
Est. Value: Parcel Number: 03-26-21-0190-00000-0080
Improv. Cost: 7,980.00 ' I r OWNER INFORMATION
Date Issued: 12/11/2019 Name: PINKSTON, BRENT D & MELISSA KEY
Total Fees: 80.00 Address: 6420 LAURELWOOD DR
Amount Paid: 80.00 ZEPHYRHILLS, FL. 33542-4869
Date Paid: 12/11/2019 Phone: 813-690-7824
Work Desc: REROOF SHINGLE
CONTRACTORS APPLICATION FEES
FOSTER ROOFING ENTERPRISE INC REROOF RESIDENTIAL 80.00}
n o
G 1
DRY IN ROOF IN P Ins ections Required
TAPE JOINTS ROOF INSP
FINAL
REINSPECTION FEES: (c)With respect to Reinspection fees will comply with Florida Statute 553.80 (2)(c)the
local government shall impose a fee of four times the amount of the fee imposed for the initial inspection or
first reinspection,whichever is greater,for each such subsequent reinspection.
NOTICE: In addition to the requirements of this permit, there maybe additional restrictions applicable to this property that
may be found in the public records of this county, and there may be additional permits required from other governmental
entities such as water management, state agencies or federal agencies.
"Warning to owner: Your failure to record a notice of commencement may result in your paying twice for
improvements to your property. If you intend to obtain financing,consult with your lender or an attorney
before recording your notice of commencement."
Complete Plans,Specifications Must Accompany Application. All work shall be performed in accordance with
City Codes and Ordinances. NO OCCUPANCY BEFORE C.O.
NO OCCUPANCY BEFORE C.O.
CON R ATURE PERMIT OFFI R
PERMIT EXPIRES IN 6 MONTHS WITHOUT APPROVED INSPECTION
CALL FOR INSPECTION - 8 HOUR NOTICE REQUIRED
PROTECT CARD FROM WEATHER
813-760-0020 City of Zephyrhills Permit Application Fato-913-780-0021
Binding Department
note Received Phone Contact for PermitOn
'JylOwnels Name Owner Phone Number lD O�
Owner's Address Owner Phone Ntmrhw
3-� 371�L
Fee Simple Titleholder Name Owner Phone Number
Fee Simple Titleholder Address
JOB ADDRESS tw Opp Lt,L/L I kkV41 FD1 /L�OT�i#��y
SUBDIVISION 1 �G 11', PARCELIDM
(OBTAMM FROM PROPGMTAY NDTII2J
WORK PROPOSED NEW CONSTR ADD/ALT = SIGN = = DEMOLISH
B INSTALL B REPAIR
PROPOSED USE = SFR Q COMM = OTHER
TYPE OF CONSTRUCTION 0 BLOCK 0 FRAME = STEEL 0
DESCRIPTION OF WORK L
BUILDING SIZE SO FOOTAGE HdGHT
=BUILDING $ �%1, VALUATION OF TOTAL CONSTRUCTION
=ELECTRICAL $ U VV AMP SERVICE Q PROGRESS ENERGY Q W.R.E.0
=PLUMBING $
=MECHANICAL $ VALUATION OF MECHANICAL INSTALLATION
=GAS ROOFING Q SPECIALTY = OTHER
FINISHED FLOOR ELEVATIONS FLOOD ZONE AREA =YES NO
BUILDER COMPANY
SIGNATURE REGISTERED I YIN FEE CURREA I Y/N
Address Ucerse#
ELECTRICIAN COMPANY
SIGNATURE REGISTERED I Y/N FEE CURREn Y—/N71
Address License#
PLUMBER COMPANY
SIGNATURE REGISTERED I YIN I FEECURREr. I YIN
Address License#
MECHANICAL COMPANY
SIGNATURE I REGISTERED I Y/N FEE CURREA )/N
Address x License#
OTHER COMPANY OS S Z '�YIt�J
SIGNATURE REGISTERED ILVI N FEE CURRM /aaN
40 Li I CM Address 9 .# Ispol
III 111111 11111111111111lollIIIIIIIIIIIIIII111111IIIIIIIIII11111111
RESIDENTIAL Attach(2)Plot Plans;(2)sets of Building Plans;(1)set of Energy Fonts;RAW Permit for new consWction,
Minimum ten(10)working days after submittal date. Required onsite,Construction Plans,Storrtwater Plans w/Sift Fence installed,
Sanitary Facilities&1 dumpster,Site Work Permit for subdivislons/large projects
COMMERCIAL Attach(3)complete sets of Building Plans plus a Life Safety Page;(1)set of Energy Forms.R-O-W Permit for new construction.
Minimum ten(10)working days after Submittal date. Required onsite,Construction Plans,Stornwater Plans wl Silt Fence installed,
Sanitary Facilities&1 dumpster.Site Work Permit for all new projects.AI commercial requirements must meet compliance
SIGN PERMIT Attach(2)sets of Engineered Plans.
PROPERTY SURVEY required for all NEW construction.
Directions:•
FII out application completely.
Owner&Contractor sign back of application,notarized
If over S25M a Notice of Commencement is required. (XC upgrades over$7500)
Agent(for the contractor)or Power of Attorney(for the owner)would be someone uft notarzed letter from owner authaiang Same
OVER THE COUNTER PERMITTING (Front of Applrad-Orly)
Retools if shingles Sewers Service Upgrades A/C Fens 0%t/Survey/Footage)
Driveways-Not over Counter if on public roadways..needs ROW
NOTICE OF DEED RESTRICTIONS: The undersigned understands that this permit may be subject to"deed'restrictions'
which may he more restrictive than County regulations. The undersigned assumes,responsibility for compliance with any
applicable deed restrictions.
UNLICENSED CONTRACTORS AND CONTRACTOR RESPONSIBILITIES: If the owner has hired a contractor or
contractors to undertake work,they may be required to be licensed in accordance with state and local regulations. If the
contractor is not licensed as required by law, both the owner and contractor may be cited for a misdemeanor violation
under state law. If the owner or intended contractor are uncertain as to what licensing requirements may apply for the
intended work,they are advised to contact the Pasco County Building Inspection Division—Licensing Section at 727-a47-
8009. Furthermore, if the owner has hired a contractor or contractors, he is advised to have the contractor(s) sign
portions of the"contractor Block"of this application for which they will be responsible. If you,as the owner sign as the
contractor,that may be an indication that he is not property licensed and is not entitled to permitting privileges in Pasco
County.
TRANSPORTATION IMPACTMILITIES IMPACT AND RESOURCE RECOVERY FEES: The undersigned understands
that Transportation Impact Fees and Recourse Recovery Fees may apply to the construction of new buildings,change of
use in existing buildings, or expansion of existing buildings,as specified in Pasco County Ordinance number 8"7 and
90-07, as amended. The undersigned also understands,that such fees,as may be due,will be identified at the time of
permitting. It is further understood that Transportation Impact Fees and Resource Recovery Fees must be paid prior to
receiving a"certificate of occupancy'or final power release. If the project does not involve a certificate of occupancy or
final power release, the fees must be paid prior to permit issuance. Furthermore, if Pasco County Water/Sewer Impact
fees are due,they must be paid prior to permit issuance in accordance with applicable Pasco County ordinances.
CONSTRUCTION LIEN LAW(Chapter 713,Florida Statutes,as amended): If valuation of work is$2,600.00 or more,I
certify that 1, the applicant, have been provided with a copy of the "Florida Construction Lien taw—Homeowners
Protection Guide°prepared by the Florida Department of Agriculture and Consumer Affairs. If the applicant is someone
other than the"owner",I certify that I have obtained a copy of the above described document and promise in good faith to
deliver it to the"owner'prior to commencement.
CONTRACTOR'SIOWNER'S AFFIDAVIT: I certify that all the information in this application is accurate and that all work
Will be done in compliance with all applicable laws regulating construction,zoning and land development. Application is
hereby made to obtain a permit to do work and installation as indicated. I certify that no work or installation has
commenced prior to issuance of a permit and that all work will be performed to meet standards of all laws regulating
construction, County and City codes, zoning regulations, and land development regulations in the jurisdiction. I also
certify that I understand that the regulations of other government agencies may apply to the intended work,and that it is
my responsibility to identify what actions I must take to be in compliance. Such agencies include but are not limited to:
- Department of Environmental Protection-Cypress Bayheads, Wetland Areas and Environmentally Sensitive
Lands,Water/Wastewater Treatment.
- Southwest Florida Water Management District-Wells, Cypress Bayheads, Wetland Areas, Altering
Watercourses.
- Army Corps of Engineers-Seawalls,Docks,Navigable Waterways.
- Department of Health & Rehabilitative Services/Environmental Health Unit-Wells, Wastewater Treatment,
Septic Tanks.
- US Environmental Protection Agency-Asbestos abatement.
- Federal Aviation Authority-Runways.
I'understand that the following restrictions apply to the use of fill:
- Use of fill is not allowed in Flood Zone"V°unless expressly permitted.
- If the fill material is to be used in Flood Zone "A", it is understood that a drainage plan addressing a
"compensating volume"will be submitted at time of permitting which is prepared by a professional engineer
licensed by the State of Florida.
- If the fill material is to be used in Flood Zone"A"in connection with a permitted building using stem wall
construction,I certify that fill will be used only to fill the area within the stem wall.
- If fill material is to be used in any area, I certify that use of such fill will not adversely affect adjacent
properties. If use of fill is found to adversely affect adjacent properties,the owner may be cited for violating
the conditions of the building permit issued under the attached permit application, for lots less than one(1)
acre which are elevated by fill,an engineered drainage plan is required.
If I am the AGENT FOR THE OWNER,I promise in good faith to inform the owner of the permitting conditions set forth in
this affidavit prior to commencing construction. I understand that a separate permit may be required for electrical work,
plumbing, signs,wells, pools, air conditioning, gas, or other installations not specifically included in the application. A
permit issued shall be construed to be a license to proceed with the work and not as authority to violate;cancel,alter,or
set aside any provisions of the technical codes,nor shall issuance of a permit prevent the Building Official from thereafter
requiring a correction of errors in plans,construction or violations of any codes. Every permit issued shall become invalid
unless the work authorized by such permit is commenced within six months of permit issuance,or if work authorized by
the permit is suspended or abandoned for a period of six(6)months after the time the work is commenced_ An extension
may be requested,in writing,from the Building Official for a period not to exceed ninety(90)days and will demonstrate
justifiable cause for the extension. If work ceases for ninety(90)consecutive days,the job is considered abandoned.
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR
PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING,CONSULT
WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COfAMENCEMENT.
FLORIOA JURAT(F.5 V.03)
OWNER OR AGENT CONTRACTOR
bs swo to(or affirmed) this hsrn and svro to(or atfirrreed)bef�Le me ws
.• hy by )rr+/Yt �t•[]S G�
Who fare pe alty kno t me or hasRtave produced Who islare person wn to me hasRrave produced
aseidentifiration. as identification.
TVLIJt J(iJ�.� PLf Notary Public Notary Public
Commission No. Commission No.
Name of Notary typed,printed or stamped Name of Notary typed,printed or stamped
Fl HEATHER D HOSFELD :_,; HEATHER D HOSFELD f'.
Notary Public-State of Florida '--`:, Notary Public-State of Florida8
• _ Commission a GG 18'298
Commission-GG'c�"298 «,
My Comm.Expires Mar 21.2022 '• fir`' my Comm.Expires Mar 2 2022-
6onded through National Notary Assn. Bonded through National Notary Assn.
I INSTR#2019202615 OR BK 10013 PG 2025 page 1 of 1
S/H 11/26/2019 03:08 PIVI Rcpt:2112235 Rec:10.00 DS:0.00 IT:0.00
Nikki Alvarez-Sowles.Esa..Pasco County Clerk&Comptroller
%scc)
Permit Nffber
Key lklumber
NOTICE OF COMMENCEMENT
TmsARiy,.mRmewmfmCumoFTmCoLwCwmFm*noN
THE:umDERmNE.D hereby om noace tbat h;xmww4s vrz te MWO to certain red pqww,aril in acconfam ub Section 713.of the
JM=dow of poperty(iWdh=*p&b* 673
a)SftWVAAndress - 6'VIO 4-g—,tj1eA.,C46e1 z e- v, 4;11J' 33--5'Y2
10wwS dwalpfion of bpovements: Reroof
3.OwnerInkinwdonorlessee— ffftLqsseecwnctedfix:tI*bV7mnent:,
a)Nameaui 7,e',7 ea ks.,toa eY2.17 LivyrehynC4 /1 -&4.
b)Kam and zNrm of tee dmpb Welhokler(ff ffaerd than Owner Wad abova)
c)Interest in Ixopertsf.
4.Contractor Infommllion
a)Nam sW address Fostees-Ropflit Enterprises P.O.Sox 633-Bfooksville,FL 34605
b)Telq*om No.:(352)799-0045 Fax No_(0pgNA(362)544-1003
&Su"(if Wkabbe,a copy of the pWoftbond Is WWdW)
a)Nave and addrem
b)Tek0one No:.
c)Amount of Bond:
&Lawler
A Nam and address
b)TekphmNo.:
7.Personswilhin the Slate ofFW*h&sWftd by u�w Q=nodcap or obardocturaftnW be urvad asp wMed by Secdon
71&13(1)(a)7.,Florida Statutes
a)Nam and address
b)T**mNoy
&a.In adMonto himsellierhasellf,OwwdesilpWm of
to receive a copy of the Lknoes Nafice as provkled in Section 713.13(1)(b),Flb;-WaStaTutee �
I;Ybons MNrdwof Person croft&Wg.-xdW by Owner
9.ExpbMon date of noticed Woommement(the exph4on dift rray not ba balbra the m0edonof conarucillon sul&W p*mttothe
con;trador,but VA be 1 ywftm the daft of ecorft w*=a 411srarit date lls q*ffaM: .20
WARN M TO OYMER:ANY PAYWDITS WWX BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COLUSICBM ARE
CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713,PART I.SECTION 71113,HDRIDA SMUTM AND CAN RESULT 01 YOUR
PAYING TWE FOR WROVE]KNM TO YOUR PROPERTY.A NOTICE OF COWEMMENT KIIST BE RECORDED AND POSTED ON
THE JOB SITE BEFORE THE FIRST IINSPECTIOW IF YOU 1NfM010 OBTAIN RWMW.,CONSULT WTH YOM LENDER OR-AN
ATTORMB -WMOR RECORDING YUURiEO-i=OF'COLVAEMCEUM.
x
p0aseal 0 Or OWOM Of LMMS(Auff=Md
Ir-IWWLBPP- .
Sbft of tWIW—A cwzdyot— !'�74 e.o*
The foregolM irannytent was bdo ft day of Y-0 V.Z,Z' .2D-2—_
by as
for
Pen"allyl(now 0 Oroduced 10 E!r
Type oflo
A4afaaynre
DOUGILMICLOWES
W
DoijGLAS CLOVES uMay2O.2D22
-v Corm #GG 210741'
E*wmatn.2022,
�►,�° • `O`�� STATE OF FLORIDA, COUNTY OF PASCO
THIS IS TO CERTIFY THAT T HE FOREGOING IS A
• 'kY
s. o TRUE AND CORRECT COPY OF THE DOCUMENT
God wL�•iect
ON FILE OR OF PUBLIC RECORD IN THIS OFFICE
WITNESS MY HAND A�D OFFICIAL SEAL THIS
• �7 2 --DAY OF t�P—A 2pI
CLER &COMPTROLLER
B . DEPUTY CLERK
12/3/2019 Florida Building Code Online
. q
r ;
t:
• �- . ,_.. w .. fit" :,: ...: .. -�;�� '.
aCIS Home I'Log In l User Registration t Hot Topics Submit Surcharge I Stats&Facts Publications ! Contact Us 4 BCIS Site Map 1 LMks Search
Product Approval
i, USER:Public User
q xhac i r
Product Approval Menu>Product or Application Search>Application Ust>Application Detail
FL# FL7006-R10
Application Type Revision
Code Version 2017
Application Status Approved
*Approved by DSPR. Approvals by DBPR shall be reviewed and ratified by
the POC and/or the Commission if necessary.
Comments
Archived r
Product Manufacturer IKO Industries Ltd
Address/Phone/Email 40 Hansen Road South
Brampton,NON-US L6W 3H4
(905)457-2880 Ext 4581
william.liu@iko.com
Authorized Signature William Liu
william.liu@iko.com
Technical Representative Bob Metz
Address/Phone/Email REMCO of Pinellas
456 Avila Circle NE
Saint Petersburg, FL 33703
(727)776-5261
rmetzOO1@tampabay.rr.com
Quality Assurance Representative Don Shaw
Address/Phone/Email IKO Industries LTD
120 Hay Rd.
Wilmington,DE 19808
(717)579-6706
don.shaw@iko.com
Category Roofing
Subcategory Asphalt Shingles
Compliance Method Certification Mark or Listing
Certification Agency FM Approvals
Validated By Locke Bowden P.E.
tki Validation Checklist- Hardcopy Received
Referenced Standard and Year(of Standard) Standard Year
ASTM D3161 modified to 110 mph 2016
ASTM D3462 2010
ASTM D7158 Class H 2O11
ASTM E108 2011
Equivalence of Product Standards
Certified By
https://www.floridabuilding.org/pr/pr_app_dtl.aspx?param=wGEVXQwtDgse7mYBd2b3K6mXtoZLhNVX8Xpl%2f[ZtFYIIVL4hTrrOTA°/`3d%3d 1/3
12/3/2019 Florida Building Code Online
Product Approval Method Method 1 Option A
Date Submitted 10/08/2017
Date Validated 10/30/2017
Date Pending FBC Approval
Date Approved 11/01/2017
Summary of Products
FL# Model, Number or Name Description
7006.1 Cambridge,Cambridge HD,Biltmore Laminated architectural fiberglass asphalt shingle
and Biltmore HD manufactured at IKO's Kankakee, IL; Hawkesbury,Ont.;
Wilmington, DE; Sylacauga,AL and Toronto,Ont. plants
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes FL7006 R10 C CAC Letter-ASTM D3161 letter-(9-26-
Approved for use outside HVHZ:Yes 2017)from FM.pdf
Impact Resistant: N/A FL7006 R10 C CAC Letter-ASTM D3462 letter-(9-26-
Design Pressure: N/A 2017),pdf
Other: FL7006 R10 C CAC Letter-ASTM E108 letter-(9-26-
2017)_pdf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R10 II IKO-187-02-01 Letter-Installation
Instructions for FBC FL7006.pd
Verified By: Duc T Nguyen 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
7006.2 Hip and Ridge 12 Cap This is a 12"x 12"fiberglass asphalt shingle used to cover the
hip and/or ridge of an asphalt shingle roof system
manufactured at IKO's Kankakee,IL,Toronto,Ont.and
Brampton,Ontario plants.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes FL7006 R10 C CAC ASTM D 3462-Shingle letter
Approved for use outside HVHZ:Yes Surveillance Audit Location- (6-28-2017)_pdf
Impact Resistant: N/A FL7006 R10 C CAC Letter-ASTM D3161 letter-(9-26-
Design Pressure: N/A 2017)from FM.pdf
Other: FL7006 R10 C CAC Letter-ASTM D3462 letter-(9-26-
2017),pdf
FL7006 R10 C CAC Letter-ASTM E108 letter-(9-26-
2017),pdf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R10 II Hip and Ridae Cap Shingle Installation
Instructions.pdf
FL7006 R10 II IKO-187-02-01 Letter-Installation
Instructions for FBC FL7006.12d
Verified By: Duc T Nguyen PE 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
7006.3 Leading Edge Plus Asphalt Shingle One piece fiberglass asphalt shingle used as a starter strip at
Starter Strip the bottom of a roof system manufactured in Brampton and
Hawkesbury,Ontario plants
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes FL7006 R10 C CAC Letter-ASTM D3161 letter-(9-26-
Approved for use outside HVHZ:Yes 2=)from FM -df
Impact Resistant: N/A FL7006 R10 C CAC Letter-ASTM D3462 letter-(9-26-
Design Pressure: N/A 2017),pdf
Other: FL7006 R10 C CAC Letter-ASTM E108 letter-(9-26-
2017)_pdf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R10 II IKO-1S7-02-01 Letter-Installation
Instructions for FBC FL7006.pdf
FL7006 R10 II Roofing-Products-Lead ing-Edge-Plus-
Application-EN(1)_pdf
Verified By: Duc T Nguyen PE 65034
Created by Independent Third Party: No
https://www.floddabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDgse7mYBd2b3K6mXtoZLhNVX8Xpl%2flZtFYIIVL4hTrrOTA%3d%3d 213
CONSTRUCTION MATERIALS
TECHNOLOGIES
October 27, 2017
IKO Industries, Ltd
120 Hay Rd.
Wilmington, DE 19809
Re: FBC FL7006
Sir(s),
PRI Construction Materials Technologies has completed a technical review and attached sealed shingle
instructions in compliance the 2017 Florida Building Code.
This review was completed based on the receipt of following evidence from IKO Industries, Ltd:
1) IKO Shingle Application Instructions—3-Tab Shingles
(EN-3Tab_Appins_8AGXEFS-2012-11—reformatted 2013-02-rev07/13-Florida)
2) IKO Laminated Shingles Application Instructions
(EN-Laminated—Appins_8TTEFS-2012-04_reformatted 2013-02-rev07/13-Florida)
3) IKO Hip and Ridge 12 Application Instructions
(EN-Hipand Ridge 12_3HRTri-2013-08_reformatted 2013-08)
4) IKO Leading Edge Plus Shingle Application Instructions
(EN-3LEP-Tri-2012-06—reformatted 2013-03)
5) ASTM D3161 Test Report(FM Approvals Project No. 3040947)
The attached instructions should be used in conjunction with the published manufacturer's application
instructions and applicable code. In the event the instructions conflict, these instructions shall govern.
Statement of Independence: PRI Construction Materials Technologies and/or Duc T. Nguyen, FL P.E.do not
have nor plan to acquire a financial interest in any company manufacturing or distributing products for which
the test reports are issued.
Signed: A*7 Signed:
2
Brad Grzybo ski Duc Wrofessional
Managing rector Florida RegiS-feredEngineer
j�LzP.E.Number:65034
Date: October 27, 2017 Date: October 27, 2017
Attachments: A) IKO Shingle Application Instructions-3-Tab
B) IKO Laminated Shingles Application Instructions
C) IKO Hip and Ridge 12 Application Instructions
D) IKO Leading Edge Plus Application Instructions
IKO-187-02-01
PRI Construction Materials Technologies,LLC. 6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:B13.621-5840 e-mail:materialstesting@pricmtcom WebSite:httpl/www.pdcmt.com
KO
Installation Instructions for
Asphalt Shingles
Page 2 of 5
IKO Shingle Application Instructions — 3-Talc Shingles
(ASTM 133161, Class F— IKO Marathon 25 AR and CRC Superglass M25AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 FBC.
UNDERLAYMENT:Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements, the first sheet overlapping the eave protection by 19",followed by full 36"widths overlapping
each preceding course by 19"or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves,with 2"horizontal laps and 4"end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized(zinc coated)roofing nails, 11 or 12 gauge,with at least 3/8"diameter heads,long
enough to penetrate through plywood or 3/4"into boards. Use 4 nails per shingle placed 6-1/8"above the butt
edge, approx. 1"and 13"from each end and 1/2"above each cutout. Drive nails straight so that nail head is
flush with, but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21"per foot(600)or more, use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2"of a joint/cutout of the underlying shingle. Seal down each
shingle at time of application with three 1"diameter(approx.size and thickness of a quarter)spots of asphalt
plastic cement placed under the shingle 2" above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-5/8".
STEEP SLOPES
1-0t2" 1-1lL"
}
rb SEALJNU STRIP
NAILS NAILS
DO NOT WAIL INTO OR ABOVE THE SEALING STRIP
PRI Construction Materials Technologies,LLC. 6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@pricmtcom WebSite:hftpJ/www.pricmt.com
I KQ
Installation Instructions for
Asphalt Shingles
Page 3 of 5
IKO Laminated Shingles Application Instructions
(ASTM D3161, Class F—Cambridge, Cambridge HD, and CRC,Biltmore AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT,THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 FBC.
UNDERLAYMENT:Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements,the first sheet overlapping the eave protection by 19",followed by full 36"widths overlapping
each preceding course by 19"or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves,with 2"horizontal laps and 4"end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized(zinc coated)roofing nails, 11 or 12 gauge,with at least 3/8"diameter heads,long
enough to penetrate through plywood or 3/4"into boards. Use 4 nails per shingle placed in the nail line 7-3/8"
below the top edge, approx. 1"and 13" in from each end. Drive nails straight so that nail head is flush with,
but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21"perfoot(60°)or more,use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2"of a joint/cutout of the underlying shingle. Seal down each
shingle at time of application with three 1"diameter(approx.size and thickness of a quarter)spots of asphalt
plastic cement placed under the shingle 2" above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-7/8".
NAILING-STEEP SLOPES APPLICATION
Use six nails as shown_
—► w t^ � .fir � ��� � �► r 1V —► �
NAIL LINE -
6 378 t w.
01 11 f]
NAILS CEMENT
PROPER APPLICATION REQUIRES THAT THE NAILS PENETRATE BOTH THE OVERLAY.AND UNDERLAY PORTIONS OFTHE SHINGLE
PRI Construction Materials Technologies,L-C.6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@p6cmtcom WebSite:httpJ/www.prlcmt.com
IKO
Installation Instructions for
Asphalt Shingles
Page 4 of 5
IKO Hip and Ridge 12 Application Instructions
(ASTM D3161, Class F—IKO Hip and Ridge 12)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION.INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT,THESE INSTRUCTIONS WILL GOVERN.
Cut hip and ridge shingles into thirds, using the perforation marks as a cutting guide. These shingles are
designed for a 51/8"(130 mm)exposure. (For a neater appearance,the top of each side of each piece has
been factory trimmed on a 1"(25 mm)taper(see drawing). Bend each piece over the hip or ridge,and nail 5
5/8" (143 mm)above the butt edge 1" (25 mm) in from each edge, exposing each piece 5 1/8" (130 mm).
Apply hip pieces starting at the lower end of the hip, working up toward the ridge. On hip roofs, apply ridge
pieces starting at each end, meeting in the middle. On gable roofs, apply ridge pieces starting at the end
opposite to the prevailing wind direction and continue to the other end. Note:To obtain a three-dimensional
effect,(which is recommended,but not required),apply hip and ridge shingles double thickness by stacking 2
pieces on top of one another,the lower piece extending about 3/4" (19 mm)further than the top piece(see
diagram).The-final shingle should be set in cement,and the exposed nail heads of the final shingle should be
covered with cement. Prior to application in cold weather, storing the shingles in a heated area will allow for
easier bending.
NOTE:SHINGLES MUST BE APPLIED PROPERLY.THEYARE DESIGNED FOR USE AS HIP AND RIDGE
SHINGLES ONLY, AND SHOULD NOT BE USED FOR ANY OTHER APPLICATIONS. WE ASSUME NO
RESPONSIBILITY FOR LEAKS OR DEFECTS RESULTING FROM POOR APPLICATION OR FAILURE TO
PROPERLY PREPARE THE SURFACE TO BE ROOFED OVER, OR FAILURE TO PROVIDE PROPER
VENTILATION IN ACCORDANCE WITH MINIMUM PROPERTY STANDARDS REQUIREMENTS.REVIEW
ALL APPLICABLE BUILDING CODES,MINIMUM PROPERTY STANDARDS,AND REQUIREMENTS PRIOR
TO APPLYING THESE SHINGLES USING THESE APPLICATION INSTRUCTIONS.
arm
w MM1
TAPER CUT
5 TB f
6W
ti62m[t�
0
PRI Construction Materials Technologies,LLC.6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@pricmtcom WebSite:http://www.pdcmt.com
IKO
Installation Instructions for
Asphalt Shingles
Page 5 of 5
IKO Leading Edge Plus Application Instructions
(ASTM D3161, Class F—IKO Leading Edge Plus)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
1. Apply any underlayment, eave protection, valley flashings,or drip edges to roof deck as required.
2. Each 39 3/8"x 131/4"(1000 mm x 336 mm)IKO Leading Edge Plus strip is perforated lengthwise for,
separation into two(2)shingles.Take one IKO Leading Edge Plus strip and fold flat at perforation to
separate.
3. Take one of the separated shingles 39 3/8"x 6 5/8"(1000 mm x 168 mm)and remove approximately
20"(500 mm). Install this shingle on the lower left corner of the roof deck, granule side up,with the
factory installed sealant adjacent to the eaves.The shingle should overhang the rake edge and eaves
by a nominal 1/4"(6 mm)minimum. Fasten the shingle to the roof deck with nails located 3"to 4"(75
mm to 100 mm)from the eave edge and 1" (25 mm) in from each end.
4. Take the leftover 20"(500 mm)piece shingle. Rotate the piece and align it vertically up the rake edge
with the factory installed sealant adjacent to the outer edge of the roof.The shingle should overhang
the rake edge by a nominal 1/4"(6 mm)minimum. Fasten.the shingle to the roof deck with fasteners
located 3"to 4" (75 mm to 100 mm)from the rake edge and 1" (25 mm) in from each end.
5. Repeat Steps 3—4 for the right lower corner of the roof deck.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge,with at least
3/8" (9 mm)diameter heads, long enough to penetrate through plywood or 3/4"(20
mm) into boards. Use 4 nails per shingle placed 3"to 4" (75 mm to 100 mm)from
the eave edge and approximately 1"and 13"(25 mm and 330 mm)in from each end.
6. Apply full-length IKO Leading Edge Plus shingles to the remaining eave edges of the roof deck.Install
the shingles granule side up with the factory applied sealant adjacent to the eaves. The shingles
should overhang the rake edge and eaves by a nominal 1/4"(6 mm)minimum. Fasten the shingles to
the roof deck with nails located 3"to 4"(75 mm to 100 mm)from the eave edge,4 nails per shingle:
7. Apply roof shingles as per the instructions printed on each product's package. Make certain the first
course of field shingle lies flush with the edges of the fastened IKO Leading Edge Plus. In this way,
the sealant on the IKO Leading Edge Plus shingles will adhere to the first-course field shingles and
help keep them from lifting in high winds.
PRI Construction Materials Technologies,U.C.6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@pdcmtcom WebSite:httpl/www.pricmt.com
.7.
. ..........
CONSTRUCTION MATERIALS
TECHNOLOGIES
October 27, 2017
IKO Industries, Ltd
120 Hay;Rd.
Wilmington, DE 19809
Re: FBC FL7006
Sir(s),
PRI Construction Materials Technologies has completed a technical review and attached sealed shingle
instructions in compliance the 2017 Florida Building Code.
This review was completed based on the receipt of following evidence from IKO Industries, Ltd:
1) IKO Shingle Application Instructions—3-Tab Shingles
(EN-3Tab—Appins-8AGXEFS-2012-11—reformatted 2013-02-rev07/13-Florida)
2) IKO Laminated Shingles Application Instructions
(EN-Laminated—Appins—BTTEFS-2012-04_reformatted 2013-02-rev07/13-Florida)
3) IKO Hip and Ridge 12 Application Instructions
(EN-HipandRidge12-3HRTri-2013-08—reformatted 2013-08)
4) IKO Leading Edge Plus Shingle Application Instructions
(EN-3LEP-Tri-2012-06—reformatted 2013-03)
5) ASTM D3161 Test Report(FM Approvals Project No. 3040947)
The attached instructions should be used in conjunction with the published manufacturer's application
instructions and applicable code. In the event the instructions conflict, these instructions shall govern.
Statement of Independence: PRI Construction Materials Technologies and/or Duc T. Nguyen, FL P.E.do not
have nor plan to acquire a financial interest in any companymanufacturing or distributing products for which
the test reports are issued.
Signed: i' Signed.
Brad Grzybo) ski Duc T. uyen
Managing Director Florida Regl•ere —fe--'onal Engineer
P.E.Number:65034
Date: October 27, 2017 Date: October 27, 2017
Attachments: A) IKO Shingle Application Instructions-3-Tab
B) IKO Laminated Shingles Application Instructions
C) IKO Hip and Ridge 12 Application Instructions
D) IKO Leading Edge Plus Application Instructions
IKO-187-02-01
PRI Construction Materials Technologies,L-C. 6412 Badger Drive Tampa,FL 33510 Tel:813-621-5777 Fax:813-621-5840 e-mail;materialstestnapricmtcom WebSite:httpJ/www.pr cmt.com
IKQ
Installation Ipstructions for
As?halt Shingles
Page 2 of 5
IKO Shingle Application Instructions — 3-Tab Shingles
(ASTM D3161, Class F— IKO Marathon 25 AR and CRC Superglass M25AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONDUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE., IN THE EVENT THE INSTRUCTION
CONFLICT,THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 F13C.
UNDERLAYMENT:Applied in accordance with building code requirements.For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements,the first sheet overlapping the eave protection by 19",followed by full 36"widths overlapping
each preceding course by 19"or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves,with 2"horizontal laps and 4"end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized(zinc coated)roofing nails, 11 or 12 gauge,with at least 3/8"diameter heads,long
enough to penetrate through plywood or 3/4"into boards. Use 4 nails per shingle placed 6-1/8"above the butt
edge,approx. 1"and 13"from each end and 1/2"above each cutout. Drive nails straight so that nail head is
flush with, but not cuffing into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21"per foot(600)or more,use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2"of a joint/cutodt of the underlying shingle. Seal down each
shingle at time of application with three 1"diameter(approx.size and thickness of a quarter)spots of asphalt
plastic cement placed under the shingle 2"above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-5/8".
STEEP SLOPES
=t
1-irz, 1-ir,
LSEAUNG SW
rA
NAILSNAILS
DO NOT MAIL INTO OR ABOVE THE SEAUNG STRIP
PR(Construction Materials Toonotogies,LLC.6412 Badger Drive Tampa,FL 33610 Tei:813-621-5777 Fax:813-621-5840 e-mail:Mateiialstesfing&demLeom WebS1te:httr.1/www.pdcmtccm
IKO
Iristallation Instructions for
Asphalt Shingles
PSge 3 of 5
IKO Laminated Shingles Application Instructions
(ASTM D3161, Class F—Cambridge, Cambridge HD, and CRC Biltmore AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 FBC.
UNDERLAYMENT:Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements, the first sheet overlapping the eave protection by 19",followed by full 36"widths overlapping
each preceding course by 19"or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves,with 2"horizontal laps and 4"end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized(zinc coated)roofing nails, 11 or 12 gauge,with at least 3/8"diameter heads,long
enough to penetrate through plywood or 3/4"into boards. Use 4 nails per shingle placed in the nail line 7-3/8"
below the top edge, approx. 1"and 13"in from each end. Drive nails straight so that nail head is flush with,
but not cutting into shingle surface. .
NAILING ON STEEP SLOPES: For steep slopes of 21"per foot(600)or more,use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2"of a joint/cutout of the underlying shingle. Seal down each
shingle at time of application with three 1"diameter(approx.size and thickness of a quarter)spots of asphalt
plastic cement placed under the shingle 2" above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-7/8".
NAILING-STEEP SLOPES APPLICATION
Use six rmiis asshown_
NAILLINE
6 31131
NAILS CEMENT
PROPER APPLICATION REQUIRES THAT THE NAILS PENETRATE BOTH THE OVERLAY AND UNDERLAY PORTIONS OF THE SHINGLE
PRI Construction Materials Technologies,I.I.C.6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@pdcmtcom WebSite:httpJ/www.prJcmt.com
IKQ
Installation instructions for
Asphalt Shingles
Page 4 of 5
IKO Hip and Ridge 12 Application Instructions
(ASTM D3161, Class F—IKO Hip and Ridge 12)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
Cut hip and ridge shingles into thirds, using the perforation marks as a cutting guide. These shingles are
designed for a 51/8"(130 mm)exposure. (For a neater appearance,the top of each side of each piece has
been factory trimmed on a 1"(25 mm)taper(see drawing). Bend each piece over the hip or ridge,and nail 5
5/8" (143 mm) above the butt edge 1" (25 mm) in from each edge, exposing each piece 5 1/8" (130 mm).
Apply hip pieces starting at the lower end of the hip,working up toward the ridge. On hip roofs, apply ridge
pieces starting at each end, meeting in the middle. On gable roofs, apply ridge pieces starting at the end
opposite to the prevailing wind direction and continue to the other end. Note:To obtain a three-dimensional
effect,(which is recommended,but not required),apply hip and ridge shingles double thickness by stacking 2
pieces on top of one another,the lower piece extending about 3/4" (19 mm)further than the top piece (see
diagram).The final shingle should be set in cement,and the exposed nail heads of the final shingle should be
covered with cement. Prior to application in cold weather, storing the shingles in a heated area will allow for
easier bending.
NOTE:SHINGLES MUST BE APPLIED PROPERLY.THEYARE DESIGNED FOR USEAS HIP AND RIDGE
SHINGLES ONLY, AND SHOULD NOT BE USED FOR ANY OTHER APPLICATIONS. WE ASSUME NO
RESPONSIBILITY FOR LEAKS OR DEFECTS RESULTING FROM POOR APPLICATION OR FAILURE TO
PROPERLY PREPARE THE SURFACE TO BE ROOFED OVER, OR FAILURE TO PROVIDE PROPER
VENTILATION IN ACCORDANCE WITH MINIMUM PROPERTY STANDARDS REQUIREMENTS.REVIEW
ALLAPPLICABLE BUILDING CODES,MINIMUM PROPERTY STANDARDS,AND REQUIREMENTS PRIOR
TO APPLYING THESE SHINGLES USING THESE APPLICATION INSTRUCTIONS.
aw
cr9mm� —'
TAPFA CUT
5 Ur
t 63V
(t62a"n}
PPJ Construction Materials Technologies,LLC. 6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialstesting@prlcmLcom WebSite:httpJ/www.pricmt.ccm
I KO
Installationdnstructions for -
Aaph'alt Shingles
Page 5 of 5
IKO Leading Edge Plus Application Instructions
(ASTM D3161, Class F—IKO Leading Edge Plus)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT,THESE INSTRUCTIONS WILL GOVERN.
1. Apply any underlayment, eave protection, valley flashings, or drip edges to roof deck as required.
2. Each'39 3/8"x 131/4"(1000 mm x 336 mm) IKO Leading Edge Plus strip is perforated lengthwise for
separation into two(2)shingles.Take one IKO Leading Edge Plus strip and fold flat at perforation to
separate.
3. Take one of the separated shingles 39 3/8"x 6 5/8"(1000 mm x 168 mm)and remove approximately
20"(500 mm). Install this shingle on the lower left corner of the roof deck, granule side up,with the
factory installed sealant adjacent to the eaves.The shingle should overhang the rake edge and eaves
by a nominal 1/4"(6 mm)minimum. Fasten the shingle to-the roof deck with nails located 3"to 4"(75
mm to 100 mm)from the eave edge and 1" (25 mm) in from each end.
4. Take the leftover 20"(500 mm)piece shingle. Rotate the piece and align it vertically up the rake edge
with the factory installed sealant adjacent to the outer edge of the roof.The shingle should overhang
the rake edge by a nominal 1/4"(6 mm)minimum. Fasten the shingle to the roof deck with fasteners
located 3"to 4" (75 mm to 100 mm)from the rake edge and 1" (25 mm) in from each end.
5. Repeat Steps 3—4 for the right lower corner of the roof deck.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge,with at least
3/8" (9 mm)diameter heads, long enough to penetrate through plywood or 3/4"(20
mm) into boards. Use 4 nails per shingle placed 3"to 4" (75 mm to 100 mm)from
the eave edge and approximately 1"and 13"(25 mm and 330 mm)in from each end.
6. Apply full-length IKO Leading Edge Plus shingles to the remaining eave edges of the roof deck.Install
the shingles granule side up with the factory applied sealant adjacent to the eaves. The shingles
should overhang the rake edge and eaves by a nominal 1/4"(6 mm)minimum. Fasten the shingles to
the roof deck with nails located 3"to 4"(75 mm to 100 mm)from the eave edge,4 nails per shingle.
7. Apply roof shingles as per the instructions printed on each product's package. Make certain the first
course of field shingle lies flush with the edges of the fastened IKO Leading Edge Plus. In this way,
the sealant on the IKO Leading Edge Plus shingles will adhere to the first-course field shingles and
help keep them from lifting in high-winds.
PRI Construction Materials Technologies,LLC.6412 Badger Drive Tampa,FL 33610 Tel:813-621-5777 Fax:813-621-5840 e-mail:materialslesting@pricmtcom WebSite:httpllwww.pdcmt.com
E
City of Zephyrhills
5335 81'St
uphyrhills FL 33542
(813)780-0020
• "y t
C
i
ROOFING INSPECTION AFFIDAVIT
!� No.: �Permit �,,,
` 2
I f
I `
licensed under Chapter468,Florida Statutes as a(n):
Contractor
License No. Engineer_Architect_ Building Inspector
i
�' 01 ► `NCO
,
k
On or about 1p ' did personally inspect the: i
Check: Roof Deck Nailing ✓ Dry in ✓ Flashing and Drip edge a.f
I Check which was used: 30#felt Peel and Stick Other(List) a 11- ,fir C
i
At the following
Lai)(-C6 Woo
address: i
i
I
Based upon that examination,I have determined the installation was done according to the Hurricane
Mitigation Retrofit Manual(Based on Section 553.844,Florida Statutes).
t
Signature:
STATE OF F RIDA
COUNTY OF PASCO
Sworn to and subscribed before this day
BY: I
Notary Public State of Florida
S-ELD
HEN tER 0 H f ponds
�' 1y"'• Notary pmbstonstate GG 161298
COm Tres that 11.2022
••'�;.::5�x�:= My E°n' National Notary NSsn.
d throufi9
Ronde
i
i