15-16497 - Laserfiche WebLink

Browse Search

� page 1 � • OLIVER TECHNOLOGIES,INC. revision 6l07 FLORIDA INSTALLATION INSTRUCTIONS FOR THE MODEL 1101 "V"SERIES ALI�STEEL FOUNDATION SYSTEM MODEL 11b1"V"(STEPS 1-15) � LONGITUDINAL dNLY.•FOLLOW STEPS 1-9 FOR ADD/NG LATE AL ARM:Follow Steps l0-15 FOR CONCRETE APP ICATIONS:Fo(!ow Steps 1&19 ENGINEERS STAMP ENGINEERS STAMP 1. SPECIAL CIRCUMSTANCES: If the following conditions occur-STOP! Contact Oliver Technologies at 9-800-284-7437: a) Pier height exceeds 48" b) Length of home exceeds�6'c) Roof eaves exceed 16"d)Sidewali height exceed 96" e) Location is within 1500 feet of coast INSTALLATION OF GROUND PAN 2. Remove weeds and debris in an approximate two foot squa�re to expose firm soil for each ground pan (C) . 3. Place ground pan (C)directly below chassis I-beam . Press or drive pan firmly into soil until flush with or below soil. SPECIAL NOTE:The longitudinal"V"brace system serves�s a pier under the home and should be loaded as any other pier. It is recommended that after leveling piers, and one-third inch (1/3")before home is lowered completely on to piers, complete steps 4 through 9 below then remove jacl�s. INSTi4LLATION OF LONGITUDINAL"V"BRACE SYSTEM NOTE: WHEN INSTALLING THE LOPIGITUDINAL SYSTEM ONLY, �►MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOIL TEST PROBE SHOULD BE USED TO DETERMINE CORRECT TYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBE TEST READINGS ARE BETWEEN 175 8�275 A 5 FOOT ANCHOR MUST BE USED.IF PROBE TEST R�ADINGS ARE BETWEEN 276&350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WITH DIAGONAL TIES AND STABILIZER PLATES EVERY 5'4".VERTICAL TIES ARE ALSO REQUIRED ON HOMES SUPPLIED WITH VERTICAL TIE CONNECTIOPI POINTS(PER FLORIQA REG�). 4.Select the correct square tube brace(E)length for set-up�pier) height at support location. (The 18"tube is always used as the bottom part of the longitudinal arm). Note: Either tube can be used by itself, cut and drilled to length as long as a 40 to 45 degree angle is maintained. PIER HEIGHT 1.25"ADJUSTABL 1.50"ADJUSTABLE (Approx.45 degrees Max.) Tube Length Tube Length .:�7;374".:to,25" =-:::;�.__;=` - - _ _- 22,��.�'.,-;:.:";_.;�, -..._-=`:-t�-�-:�=-.� ,=_' -_ - -=-18„ _-- _ = • ,_ . _ .:. . _� =- - -} -' - - - - 24 3/4"to 32 1/4" �.= 32 I � 1 g ` - -- � _. - _:.. � „ - '� -44„ : .-; _ . -.;..33=to�41 °::..:.�:_.�:;'.<-::�-'" -' ._�- _.=-:- - - -�'--'-�___ -_ _ _-_ _ _ -=-- -- _ �18"- -;-,.;=-_:•.<_:. 40"to 48" 54�� I = - - - 18� 5. Install (2)of the 1.50"square tubes(E {18"tube})into thl"U°bracket(J), insert carriage bolt and leave nut loose for final adjustment. 6. Place I-beam connector(F)loosely on the bottom flange f the I-beam. 7. Slide the selected 1.25"tube(E)into a 1.50"tube(E)and attach to I-beam connectors(F)and fasten loosely with bolt and nut. 8_ Repeat steps 6 through 7 to create the"V" pattern of the quare tubes loosely in place.The angle is not to exceed 45 degree and not below 40 degrees. 9.After all bolts are tightened,secure 1.25"and 1.50"tubes i sing four(4) 1/4"-14 x 3/4"self-tapping screws in pre-drilled holes. INSTALLATION OF LATERAL TELESGOPING TRANSVERSE ARM SYSTEM THE MODEL 1101 "V"(LONGITUDINAL 8�LATERAL PROTECTIO )ELIMINATES THE NEED FOR MOST STABILIZER PLATES 8�FRAME TIES. NOTE:THE USE OF THIS SYSTE REQUIRES VERTICAL TIES SPACED AT 5'4". FOUR FOOT(4')GROUND ANCHOR MAY BE USED IXCEPT WHERE THE HOME MANUFACTURER SPECIFIES DIFFERENT. 10. Install remaining vertical tie-down straps and 4'ground anlchors per home manufacturer's instructions. nlo7e: Centerline a�chors to be sized according to soil torque condition.An� manufacturer's specifications for sidewall anchor loads in excess of 4,000 Ibs. require a 5'anchor per Florida Code. 11. No7'e:Each system is required to have a frame tie and stabilizer attached at each lateral arm stabilizing location.This frame tie& stabilizer plate needs to be located within 18"from of ce �ter ground pan. 12. Select the correct square tube brace(H)length for set-up�lateral transverse at support loca6on.The lengths come in either 60" or 72"lengths. (With the 1.50"tube as the bottom tube, a��d the 1.25"tube as the inserted tube.) 13. Install the 1.50 transverse brace(H)to the ground pan connector(D)with bolt and nut. 14. Slide 1.25"transverse brace into the 1.50°brace and attach to adjacent I-beam connector( I )with bolt and nut. 15. Secure 1_50"transverse arm to 1.25"transverse arm usir�q four(4) 1/4"- 14 x 3/4"self-tappin4 screws in ore-drilled holes • � { OLIVER TECHNOLOGIES, INC. Telephone:931-796-4555 1-800-2847437 Fax:931-796-8811 www.olivertech nolegies.com