Laserfiche WebLink
r <br /> . , <br /> , , <br /> `.o � �'�� �- . • �. . <br /> R� � R�of ° IIQ ! <br /> Acrylic Elastomeric Roof Coating — Standard <br /> i <br /> � <br /> f�@araufact�are�. i Te�tAn�&Approv�lse <br /> Conklin Company Inc. i UL-790 Fire Rating* Class"A" <br /> 551 Valley Park Drive , State of Florida No. FL-4110 <br /> Shakopee, Minnesota 55379 I US Dept.of Energy Energy Star Rated <br /> (800)888—8838 Fax(952)496-4285 � Cool Roof Ratings <br /> Pr�duct Descr6p�aon: � <br /> Council Approved <br /> Basic use:Rapid Roof�III is an elastomeric,acrylic, � �I��hO�OC�O D�$�: <br /> monolithic roof coating in a bright white, light tan, <br /> or light gray finish. It is designed to completely Resin Type Acrylic <br /> waterproof a number of approved substrates, i Color �Nhite,Light Tan, Light <br /> which includes:metal roofs,spray polyurethane , Gray <br /> foam,membrane roofs and Conklin's Fabric � Coverage 1.9 gallons per 100 sq.ft. <br /> Reinforced System. ' Density 12.0 Ibs./Gallon <br /> � <br /> Limitations:Must not be applied at temperatures i Thickness 13.5 dry mils per coat <br /> below 40°F or during inclement weather.Surface � �umber of Coats Base&Top Coat <br /> temperature must be at least 5°F above dew point i Dry Time** 2-8 Hours <br /> and relative humidity less than 80 percent to � VOC Content 71 g/L(0.6 Ibs./gal) <br /> ensure dry surfaces. Mix thoroughly before use. <br /> Ambient temperature should not exceed 100°F I Elongation 303%(Base&Top) <br /> and surface temperature should not exceed 120°F. � ASTM D-412 <br /> The polyurethane foam must be free of ponding I Tensile Strength 232 psi(Base&Top) <br /> water.By definition a roof surface which has more � ASTIVI D-412 <br /> than 36 sq.ft.of water in any area%"deep or � Pass 1/2", Mandrel-40°F <br /> more,48 hours after a rain,shall be considered i Flexibility <br /> ASTM D-1737 <br /> unacceptable.All water shall drain off of the roof. � Solar Reflectivity 85%-ASTM E-903 <br /> Small "bird baths"cannot account for more than 5 � � <br /> percent of the entire roof surface. Standard 7est <br /> i Method for acrylic Pass-ASTM D6083-97 <br /> Sizes:Available in 5-gallon containers,55-gallon i coatings <br /> drums and 220-gallon mini-bulks. i <br /> ; *Refer to Underwriters Laboretories Roofing Materials and <br /> ' i Systems directory for speciflc flre resistance assemblies or <br /> Coverage Rate:Rapid Roof III should be applied at , contact Conklin Roofing Systems. <br /> 1.9 gallons per 100 square feet. i <br /> *'Dry time for Rapid Roof III will vary depending on <br /> Cort�par��or� pr�d�cts� ' tempereture,humidity,thickness at which the product is <br /> applied and wind.Lower wind speed,higher humidity or higher <br /> • Rapid Roof I II Base Coat I wet film thickness will increase the dry time in excess of the <br /> • Tack Coat Primer I reported averege. <br /> • Prime Time ; �ppei��g��n: <br /> • Prime Time Plus I <br /> • Metal Ready Universal � Mixing/thinning: Do not mix or thin Rapidroof III. <br /> � Surface Preparation:The substrete must be <br /> structurally sound,solid,clean and dry.On certain <br /> i decks and surfaces,proper installation of drains, <br /> I vapor retarders,roofing vents,expansion joints, <br /> � <br />