16-17238 - Laserfiche WebLink

Browse Search

i' � page 1 OLIVER TECHNOLOGIES,INC. revision 6/07 _ ' FLORIDA INSTALIATION INSTRUCTIONS FOR THE MODEL 1101 "V"SERIES ALL STEEL FOUNDATION SYSTEM MODEL 1101"V"(STEPS 1-15) LONGITUDINAL ONLY:FOLLOW ST�PS 1-9 FOR ADDING LATERAL ARM:Follow Steps 10-15 FOR CONCRETE APPLICATIONS:Follow Steps 16-19 ENGINEERS STAMP ENGINEERS STAMP 1.SPECIAL CIRCUMSTANCES: If the following conditions occur-STOP! Contact Oliver Technologies at 1-800-2847437: a)Pier height exceeds 48" b) Length of home exceeds 76'c)Roof eaves exceed 16"d)Sidewall height exceed 96" e)Location is within 1500 feet of coast INSTALLATION OF GROUND PAN 2. Remove weeds and debris in an approximate two foot square to expose firm soil for each ground pan(C) . 3. Place ground pan(C)directly below chassis I-beam. Press or drive pan firmly into soil until flush with or below soil. SPECIAL NOTE:The longitudinal"V"brace system serves as a pier under the home and should be loaded as any other pier. It is recommended that after leveling piers,and one-third inch(1/3°)before home is lowered complete(y on to piers,complete steps 4 through 9 below then remove jacks. INSTALLATION OF LONGITUDINAL"V"BRACE SYSTEM NOTE: WHEN INSTALLING THE LONGITUDINAL SYSTEM ONLY, A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOIL TEST PROBE SHOULD BE USED TO DETERMINE CORRECT TYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBE TEST READINGS ARE BETWEEN 175 8 275 A 5 FOOT ANCHOR MUST BE USED.IF PROBE TEST READINGS ARE BETWEEN 276�350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WRH DIAGONAL TIES AND STABILIZER PLATES EVERY 5'4".VERTICAL TIES ARE ALSO REQUIRED ON HOMES SUPPLIED WITH VERTICAL TIE CONNECTION POINTS(PER FLORIDA REG.). 4.Select the correct square tube brace(E)length for set-up(pier)height at support location. (The 18"tube is always used as the bottom part of the longitudinal arm). Note: Either tube can be used by itself, cut and drilled to length as long as a 40 to 45 degree angle is maintained. PIER HEIGHT 1.25"ADJUSTABLE 1.50"ADJUSTABLE (Approx.45 degrees Max.) Tube Length Tube Length : 7 3/4°to 25° . , : 22" _ - - :- 18" _ ._ : . 24 3/4"to 32 1/4" 32° 18" �' 33°to 41" - . . 44n_ °.: ` � -18" .,. ., _ . 40°to 48" 54" 18" 5. Install (2)of the 1.50"square tubes(E {18"tube})into the"U"bracket(J),insert carriage bolt and leave nut loose for final adjustment. 6. Place I-beam connector(F)loosely on the bottom flange of the I-beam. 7. Slide the selected 1.25"tube(E)into a 1.50"tube(E)and attach to 1-beam connectors(F)and fasten loosely with bolt and nut. 8. Repeat steps 6 through 7 to create the"V"pattem of the square tubes loosely in place.The angle is not to exceed 45 degree and not below 40 degrees. 9.After all bolts are tightened, secure 1.25"and 1.50"tubes using four(4)1/4"-14 x 3/4"self-tapping screws in pre-drilled holes. 1N�,TALLoTION OF LeTERAL TELESCOPING TRA_NSVERSE ARM SYSTEM � THE MODEL 1101 "V"(LONGITUDINAL&LATERAL PROTECTION)ELIMINATES THE NEED FOR MOST STABILIZER PLATES 8�FRAME TIES. NOTE:THE USE OF THIS SYSTEM REQUIRES VERTICAL TIES SPACED AT 5'4". i FOUR FOOT(4')GROUND ANCHOR MAY BE USED DCCEPT WHERE THE HOME MANUFACTURER SPECIFIES DIFFERENT. � 10. Install remaining vertical tie-down straps and 4'ground anchors per home manufacturer's instructions. No'rE:Centerline II, anchors to be sized according to soil torque condition.Any manufacturer's specifications for sidewall anchor loads in excess of I 4,000 Ibs. require a 5'anchor per Florida Code. 11. NOTE:Each system is required to have a frame tie and stabilizer attached at each lateral arm stabilizing location.This frame tie 8� stabilizer plate needs to be located within 18"from of center ground pan. 12.Select the correct square tube brace(H)length for set up lateral Vansverse at support location.The lengths come in either 60" or 72"lengths. (With the 1.50"tube as the battom tube, and the 125"tube as the inserted tube_) 13. Install the 1.50 transverse brace(H)to the ground pan connector(D)with bolt and nut. 14.Slide 1.25"transverse brace into the 1.50"brace and attach to adjacent I-beam connector(I )with bolt and nut. 15 Secure 1.50"transverse arm to 1.25"transverse arm usinq four(41 1/4"-14 x 3/4"self-tappinq screws in pre-drilled holes. OLIVER TECHNOLOGIES,INC. Telephone:931-796-4555 1-800-284-7437 Fax:931-796-8811 www.olivertechnologies.com