16-17343 - Laserfiche WebLink

Browse Search

1' 1 r � � page 1 OLIVER TECHNOLOGIES,INC. revision 6/07 FLORIDA INSTALLATION INSTRUCTIONS FOR THE I MODEL 1101"V"SERIES ALL STEEL FOUNDATION SYSTEM MODEL 1101"V"(STEPS 7-75) LONGITUDINAL ONLY.•FOLLOW STEPS 1-9 FOR ADDlNG LATERAL ARM:Follow Steps 10-15 FOR CONCRETE APPlJCATIONS:Follow Steps 16-19 ENGINEERS STAMP ENG�NEERS STAMP 1.SPECIAL CIRCUMSTANCES: If the following conditions occur-STOP! Confact Oliver Technologies at 1-800-2847437: � a)Pier height exceeds 48" b) Length of home exceeds 76'c)Roof eaves exceed 16"d)Sidewall height exceed 96" e)Location is within 1500 feet of coast INSTALLATION OF GROUND PAN 2. Remove weeds and debris in an approximate two foot square to expose firm soil for each ground pan(C). 3. Ptace ground pan(C)directly below chassis I-beam . Press or drive pan firmly into soil until flush with or below soil. SPECIAL NOTE:The longitudinal"V"brace system serves as a pier under the home and should be loaded as any other pier. It is recommended that after leveling piers,and one-third inch(1/3")before home is lowered completely on to piers,complete steps 4 through 9 below then remove jacks. INSTALLATION OF LONGITUDINAL"V"BRACE SYSTEM NOTE: WHEN INSTALLING THE LONGITUD/NAL SYSTEM ONLY, A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOIL TEST PROBE SHOULD BE USED TO DETERMINE CORRECT TYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBE TEST READINGS ARE BETWEEN 175 8 275 A 5 FOOT ANCHOR MUST BE USED.IF PROBE TEST READINGS ARE BETWEEN 276 8 350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WRH DIAGONAL TIES AND STABILlZER PLATES EVERY 5'4".VERTICAL TIES ARE ALSO REQUIRED OPI HOMES SUPPUED WITH VERTICAL TIE GONNECTION POINTS(PER FLORIDA RECx). 4.Select the correct square tube brace(E)length for set-up(pier)height at support location. (The 18"tube is always used as the bottom part of the longitudinal arm). Note: Either tube can be used by itself,cut and drilled to length as long as a 40 to 45 degree angle is maintained. PIER HEIGHT 1.25"ADJUSTABLE 1.50"ADJUSTABLE (Approx.45 degrees Max.) Tube Length Tube Length 7 3/4°to 25"•; , - -- - - 22°' -. ' _ , _ . - - : 18° - - , 24 3/4"to 32 1/4" 32° 18" = 33n to 41". '-_:.- , , . .. 44"..., . - � �-=18" - - . 40°to 48" - 54° 18" - 5. Install (2)of the 1.50"square tubes(E {1 S"tube})into the"U"bracket(J), insert carriage bolt and leave nut loose for final adjustment. 6. Place I-beam connector(F)loosely on the bottom flange of the I-beam. 7. Slide the selected 1.25°tube(E)into a 1.50"tube(E)and attach to I-beam connectors(F)and fasten loosely with bolt and nut. 8. Repeat steps 6 through 7 to create the"V"pattem of the square tubes loosely in place.The angle is not to exceed 45 degree and not below 40 degrees. 9.After all bolts are tightened, secure 1.25"and 1.5p"tubes using four(4)1/4"-14 x 3/4"self-tapping screws in pre-drilled�holes. INSTALLATION OF IATERAL TELESCOPING TRANSVERSE ARM SYSTEM THE MODEL 1101 "V"(LONGITUDINAL&LATERAL PROTECTION)ELIMINATES THE PIEED FOR MOST STABILIZER PLATES 8�FRAME TIES. NOTE:THE USE OF THIS SYSTEM REQUIRES VERTICAL TIES SPACED AT 5'4". FOUR FOOT(4')GROUND ANCHOR MAY BE USED EXCEPT WHERE THE HOME MANUFACTURER SPECIFIES DIFFERENT. 10. Install remaining vertical ti�down straps and 4'ground anchors per home manufacturer's instructions. NOTE:Centerline anchors to be sized according to soil torque condition.Any manufacturer's specfications for sidewall anchor loads in excess of 4,000 Ibs. require a 5'anchor per Florida Code. 11. NOTE:Each system is required to have a frame tie and stabilizer attached at each lateral arm stabilizing location.This frame tie& stabilizer plate needs to be located within 18"ftom of center ground pan. 12. Select the cor�ect square tube brace(H)length for set-up lateral transverse at support location.The lengths come in either 60" or 72"lengths. (With the 1.50"tube as the bottom tube, and the 1.25"tube as the inserted tube.j 13. Install the 1.50 transverse brace(H)to the ground pan connector(D)with bolt and nut. ' 14. Slide 1.25"transverse brace into the 1.50"brace and attach to adjacent I-beam connector(I )with bolt and nut. 15.Secure 1.50"transverse arm to 1.25"transverse arm usinq four(4) 1/4"-14 x 3/4"self-tappinq screws in pr�drilled holes. ; ; OLIVER TECHNOLOGIES,INC. Telephone:931-796-4555 1-800-2847437 Fax:931-796-8811 www.olivertechnologies.com