16-17418 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Specificatians .- . General SpectrAlert Advance horns,strobes,and norn strabes shali maunt to a siandard 4 x 4 x 1 Yz-inch back bax,4-inch octagon back bax,or double-gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch 6ack box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate. Alsa,SpecirAlert Advance products,when used with the Sync•CircuiY""Module accessory,shail be powered from a nan-coded natification �� appliance circuit output and shail operate on a nominai 12 or 24 volts.When used with the Sync•Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volk-rated notification appliance circuit outputs shall operate between � 16,5 and 33 volts.indoor SpectrAfert Advance products shall operate betwsen 32 and 120 degrees Fahrenheit from a regulated DG ar full- • wave rectified unfiltered power supply.Strobes and horn strobes shall have fieid-selectable candela settings including 15,15/75,30,75,95, i� 110,116,135,150,177,and 185. Strobe ' The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved far fire pratective service. ( The strobe shall be wired as a primary-signaling noEification appliance and comp(y with the Americans with Disabilitiss Act requirements tar � visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Hom Strobe Combinatian The horn strobe shalf be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shell be approved for fire protective service.The hom strobe shall be wired as a primary-signaling notificatian appliance and comply with the Americans with � Disabilities Act requirem�nts for visible signaling appiiances,flashing at 1 hlz over the strobe's entire operating voltage range.The strobe light shall cansist of a xenon flash tube and associated lens/reflector system.The hom shall have three audibifity options and an aption ro switeh between a temparal three pattern and a non-ternpora!{continuous}pattern.These optians are set by a multiple position switch.On four-wire producis,the strobe shall be powered independently of the soundec The horn on horn strabe models shall operate an a coded or nan-coded power supply. Synchranization Module The module shall be a System Sensor Sync•Circuit modei MDL3 listed to UL 464 and shaii be approved for fire protective service.The module shail synchranize SpectrAlert strobes at 1 Hz and horns at temporal three.Also,whiie operating the strobes,the module shall si(ence the horns on horn strobe models aver a single pair of wires,The madule shall mount to a 411/16 x 411/16 x 21B-inch back box.The module shall also contro!two Style Y{ciass B}circuiis or one Style Z(ciass A}circuit.The module shali synchronize muitiple zanes.Qaisy chaining two or mare synchronization modules together will synchronize alI the zones they control.The module sha(i not aperate on a coded power supply. .- . Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Stro6e FEash Rate 1 fiash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR' Qperating Vottage Rangez $ta 17.5 V{12 V nominal)or 16 ta 33 V(24 V nominal} Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) InputTerminal Wire Gauge 12 to 18 AWG WaII-Mount dimensions(including tens) 5.6"L x 4 7""W x 2.5""D(142 mm L.x 119 mm W x 64 mm D) Morn Dimensions 5.6"L x 4 7"W x 1,3"D(142 mm L x 119 mm W x 33 mm D) WaI1-Mannf'irim Ring Dimensians{sold as a 5 pack}{TR-HSj 5.7"L x 4.8"W x 0.35"D{1A5 mm L x 122 mm 1N x 9 mm O} Notes; 1.FuI!Wave Rectified(FiNft}vo(tage is a non-regulated,time-varying power saurce that is used an some pawer supply and panei outputs. 2.P,S,PC,and SC products will operate at 12 V naminal only for 15 and 15/75 cd,