16-17664 - Laserfiche WebLink

Browse Search

e ,: ��SimplEx � . TrueA/arm Analog Sensing UL, ULC, CSFM Listed; FM Approved; TrueAlarm Analog Sensors — Photoelectric ; MEA (N�YC) Acceptance* and Heat; Standard Bases and Accessories �� TrueAla�m analog sensing provides: _ ____ _ _ • Digital transmission of analog sensor values via lDNet !� or MAPNET II two-wire communications For use�with the following Simplex° products: � • 4007ES,4010,4010ES,4100ES, and 4100U Series �� control panels; and 4008 Series control panels with reduced feature set(refer to data sheet S4008-0001 for details) • 4020,i 4100,and 4120 Series control panels,Universal 4098-9714 TrueAlarm Photoelectric Transponders, and 2120 TrueAlarm CDTs equipped Sensor Mounted in Base for MAPNET II operation — Fire alarm control panel provides: ■ _ . . • Peak value logging allowing accurate analysis of each � sensor for individual sensitivity selection Digital Communication of Analog Sensing. • Sensitivity monitoring satisfying NFPA 72 sensitivity TrueAlarm analog sensors provide an analog testing requirements; automatic individual sensor measurement digitally communicated to the host control calibration check verifies sensor integrity panel using Simplex addressable communications. At the • Automatic environmental compensation,multi-stage control panel,the data is analyzed and an average value is alarm operation,and display of sensitivity directly in determined and stored. An alarm or other abnormal percent per foot condition is determined by comparing the sensor's present • Ability to display and print detailed sensor value against its average value and time. information in plain English language Intelligent Data Evaluation.Monitoring each sensor's Photoelectric smoke sensors provide: average value provides a continuously shifting reference • Seven levels of sensitivity from 0.2%to 3.7% point.This soflware filtering process compensates for (refe I to additional information on page 3) environmental factors (dust, dirt,etc.)and component Heat sensors provide: aging,providing an accurate reference for evaluating new • Fixe�temperature sensing activity.With this filtering,there is a significant reduction • Rate-'�of-rise temperature sensing in the probability of false or nuisance alarms caused by • Utility temperature sensing shifts in sensitivity, either up or down. �i • Listed to UL 521 and ULC-S530 Control Panel Selection.Peak activity per sensor is i General features: stored to assist in evaluating specific locations.The alarm • Oper�ation is for ceiling or wall mounting set point for each TrueAlarm sensor is determined at the • Listed to UL 268 and ULC-S529 host control panel,selectable as more or less sensitive as I the individual application requires. • Louvered smoke sensor design enhances smoke capture by directing flow to chamber; entrance areas Timed/Multi-Stage Selection.Sensor alarm set points are mmimally visible when ceiling mounted can be programmed for timed automatic sensitivity • Designed for EMI compatibility selection(such as more sensitive at night,less sensitive • Magnetic test feature is provided during day). Control panel programming can also provide • Diffe�rent bases are available to support a supervised multi-stage operation per sensor.For example, a 0.2% or un�supervised output relay, and/or a remote LED level may cause a warning to prompt investigation while a alarm indicator 2.5°/a level may initiate an alarm. Additional base reference: Sensor Alarm and Trouble LED Indication.Each • For isolator bases,refer to data sheet 54098-0025 sensor base's LED pulses to indicate communications • For s�'lounder bases,refer to data sheet S4098-0028 with the panel.If the control panel determines a sensor is • For photo/heat sensors, refer to data sheet S4098-0024 in alarm, or is dirty or has some other type of trouble,the (single address)and 54098-0033 (dual address) details are annunciated at the control panel and that sensor ' These pr�ol,ducts have been approved by the California State Fire Marshal(CSFM)pursuant to base's LED will be turned on steadily.During a system Section 13144.1 of the California Health and Safety Code.See CSFM Lis6ngs alarm,the control panel will control the LEDs such that 7272-0026:218,�2��-oo2s:23�,�2�o-oo2s:2�s,and 7300.0026:217 for allowable values an LED indicating a trouble will return to pulsing to help andlor co�ditions concerning material presented in this document.Accepted for use—City of New Yorl�Department of Buildings—MEA35-93E.AddiGonal listings may be applicable, identify the alarmed sensors. contact your local Simplex product supplier for the latest status.Listings and approvals under Simplex Time Recorder Co.are the property of Tyco Fire Protection Products. � S4098-0019-20 1/2015 i