16-17664 - Laserfiche WebLink

Browse Search

� � . . . . - - Duct Sensor Location Considerations: - � 1. Proper duct smoke detection location must ensure ''; /Exhaust Damper sensor oK adequate airflow within the duct housing. i� 2. Duct air velocity rating is 300 to 4000 ft/min(91 to ' Exhaust.-' � �--Return air 1220 m/min). Pressure differential between intake ' and exhaust tubes is required to be between 0.015 to �o not iocate ; 1.55 inches of water(0.381 to 3937 mm). j sensor here ; 'I 3. Ensure accessibility for test and service. Return air damper 4. Proper Locations: downstream side of filters to detect fires in the filters; in return ducts, ahead of mixing areas;upstream of air humidifier and cooling coil. 5. Other locations and orientations may be required for Fresr,air-� i -•SupplyAir proper duct smoke detection depending on duct � � � access,system design, and duct airflow testing. �I oo not iocate Filter bank Sensor OK Contact your local Simplex product supplier for � sensor here aSSlStariCe. I Locations to Avoid: Additional Information. Refer to NFPA 90A,Standard 1. Where dampers closed for comfort control would for the Installation ofAir Conditioning and Ventilating interfere with airflow. Systems;NFPA 72,the National Fire Alarn:and Signaling 2. Next to outside air inlets(unless the intent is to Code; and the NE�LIA Guide for Proper Use of Smoke monitor smoke entry from that area). Detectors in Dirct Applications,and Installation Instructions 3. In return air damper branch ducts and mixing areas 574-776.,� where airflow may be restricted. . - . General��Mechanical and Environmental Air Velocity Range(linear ft/min) 300 to 4000 ft/min (91 to 1220 m/min) Sensor Sensitivity Range 0.2%to 3.7%per foot of obscuration, selectable at host control panel UL Listed Temperature Range 32° F to 100° F(0°C to 38° C) Operating Temperature Range 32° F to 122° F(0°C to 50° C) Storage Temperature Range 0° F to 140° F(-18°C to 60°C) Humidity Range 10%to 95% RH, non-condensing Wiring Connections Terminal blocks, 18 to 12 AWG(0 82 mmZ to 3.31 mmZ) Housing Color and Material Black ABS base with clear polycarbonate cover Sampling and Exhaust Tube Material Black CPVC,custom extrusion; sampling tubes are pre-drilled Remote„IStatus/Alarm LED and Test Station with Remote Status/Alarm LED Remote Alarm LED Current 1.2 mA, no impact to 24 VDC alarm current(2098-9808 or 2098-9806) Test Station Keyswitch Current 3 3 mA, no impact to 24 VDC alarm current(2098-9806) Remote Alarm LED and Test Station Distance 250 ft(76 m)maximum Addressable Operation Data Communications IDNet or MAPNET II communications, auto-select, one address per housing; ,I provides operating power to model 4098-9755 Model 4098-9756 with Supervised Multiple Relay Control,Requires Separate Fused 24 VDC from Fire Alarm Power Supply Input�/oltage 18-32 VDC(24 VDC nominal) Standby Current 3 mA @ 24 VDC Alarrtj Current 15 mA @ 24 VDC; add 15 mA for each 4098-9843 relay For use with 4098-9843 relay only, quantity of 15 maximum,distance of 500 ft Supe��vised Remote Relay Control Output (152 m)maximum; requires 4081-9008(ref 733-894) 10 kS2, 1/2 W end-of-line ,� resistor 4098-98tl43 Relay Output Ratings,Single Form C, use with Model 4098-9756 Only Coil Current 15 mA @ 24 VDC, up to 15 maximum per relay control output Relay;Contacts 7 A at 0.35 PF @ 28 VDC& 120 VAC;250 NA @ 5 VDC Locatlion Distance 500 ft(152 m)maximum to relay coils;locate relays within 3 ft(1 m)of device ;� being controlled per NFPA 72 � TYCO,SIMPLEX,and the product names lisled in(hrs material are marks anc!/or registered marks.Unauthorrzed use is strrctly prohrbrled NFPA 72 and Narrona!Frre Alarm and Signahng Code are regislered[rademarks ojthe Na(iana!Fire Prolec(ion Associa[ion(NFPA). .T.��S i m p I Ex Tyco Fire Protection Products•Westminster,MA•01441-0001•USA S4098-0030-10 11/2014 � www.simp/ex-fire.com C120/-1 Tyco Fire Prolection Products.A!!righ[s reserved Al1 spectfications and alher infarmation shown were curren!as ofdocunten(rewsion dale and are subject to change withou(notice.