17-18343 - Laserfiche WebLink

Browse Search

— — — --�-., .. — .... -..:. -- :-- � � s � , � ! i �RINITY' �RD 6.5.2 Flintlastic GTA shall be fully torch applEed to the substrates noted in Sectlan 5.5. Side (horizantaly laps shail be minimum 3-inch a�d end(vertical)laps minimum b-inch wide,and aft3et end-laps minimum 3 feet from course to course. Side and�nd-laps shaH be fuliy heat-welded and inspected#o ensure minimum 3j8-inch fiow of m dified campo�nd beyandjthe iap edge. , 6.5.3 Tile shall be loade and staged in a manner xhat prevents tile slippage andJor damage to the underiayment. ' 6.5.4 Cansuit CertainTe d instructions regarding back-nailing requirements. 6.6 Flintlastic GMS ar lintlastic Premium GfVIS: 6.6.1 Flintiastic GMS or Flinttastic Premium 6M5 shal� be installed in compliance with current CertainTesd pu lished instaitation requir,ments. for use in tile applications,reference is made to FRSA/TRI April 2012(Q4-12) Inst Ilation Manual,Sth Editio and Table 1 herein. 6.6.2 FNntlastic GMS or�fintlastic Prernium GNi5 shal)be fully asphalt-appiied to the substrates noted in Section 5. . Side (horizontal)laps s aii be minimum 3-inch and end(vertical}iaps minimum 6-inch wide,and offset end-laps mi imum 3 feet fram cours�to course, Side and end-iaps shalt be fu�ty adhered in a complete mopping of hot aspha t with asphait extending�pproximatety 3/8-inch beyond the lap edge. 6.6.3 Tile shall be loaded and staged in a manner that prevenLs tile slippage and/or damage to the underlayment. � 6.5.4 Consuit CertainTe mstructions regarding back-naiting requirements. I �•7 Roofers'Select: � 6.7.1 Standard-510 e A lication 4:12 and reater: Starting at the lower edge of the roof,apply a single layer of Roofers' Select parallei to t e eaves,averhanging drip edge by Y:-inch. Overlap ends{vertical laps)at least 4-inch an�sides (horizontat laps)a least 2-inch. Qffset end laps fram course to course at least 6-feet.Apply flat and unwr nkted, fastening as requir d to hold in place. - 6-7•2 Law Siooe Aoplica�on 2:12 u to 4:12 : Starting at the lower edge of the roof,cover the entire deck by app ying a daubfe(ayer of Ro-fers'Select parallel to the eaves. Begin by applying a 19-inch wide starter strEp of Roofers'Select I along the eaves,o erlapping the drip edge by%:-inch.Place a ful!-width sheet over the starter,with lower edg flush to the starter's lo er edge_ Apply succeed3ng 36-inch wide caurses up the roof slope, averlapping the pr�vious ' course by 19-inch i "shingle-fashion". Qverlap ends at least 12-inch.Offset end iaps from course ta murse a�t ieast 6-feet. Apply flat a d unwrinkled,fastening as required to hotd in piace. 6.7.3 Eaves Flashin� fa Ice Dam Protection (all sloaes): Eaves flashing rnay be canstructed from self-ad ering waterproofing un rlayment holding Fforida Product Approvat, or by applying a double laysr of Roofers' Select cernented togethe with asphalt roofing cement{ASTM D 4586,Type!!}. Eaves ffashing shauid be instailed to�levei of at least 24-inch inside the interiar waii line, ar in areas of severe icing, at teast up to the highest wate levef expected to occur am ice dams to the satisfaction of the Autfiority Naving lurisdiction. 7• BUILpING PERMIT REQUlREME��S: As required 6y the euiiding Offi�ial or Authority Having Jurisdiction in o�der to properly evaluate the installation of this prod ct. i $. MANUFACi'URIN6 PlANTS: � Contact the manufacturer or th�named Ct/�entity for information on ptants covered under Rute 61G20-3 QA requirements. b. QUALITYASSURANCE ENTITY: j3 Ul,L.IC.—QUA4625;{424}248-$409;karen.buchmann@ul.com r i � -END OF EVALUATION FiEPOR7- f � � I � i , � . 1 I i E�enor Research and Design,LlC, � Evaluation Report 11610.49.0�8�-R24 Certifrcate ofAuthorhation#9503 ' FL112B8-R13 ; Revision 14:03J32J1t015 � Page�of 7