17-18592 - Laserfiche WebLink

Browse Search

F�RM R�D5-2014 � ' ' Florida Department of Business and Professional Regulations Residential Whole Buildin PerFormance and Prescri tive Methods ADDRESS: Perrriit Number: Zephyrhills,FL, MANDATORY REQUIREMENTS See individual code sections for full details. � 401.3 Energy Performance Level(EPL)display card(Mandatory). The building official shall require that an energy performance level(EPL) display card be completed and certified by the builder to be accurate and correct before final approval of the building for occupancy.Florida law [Section 553.9085,Florida Statues]requires the EPL display card to be included as an addendum to each sales contract for both presold and nonpresold residential buildings.The EPL display card contains information indicating the energy performance level and efficiencies of components installed in a dwelling unit.The building official shall verify that the EPL display card completed and signed by the builder accurately reflects the plans and specifications submitted to demonstrate compliance for the building.A copy of the EPL display card can be found in Appendix C. � R402.4 Air leakage(Mandatory). The building thermal envelope shall be constructed to Iimit air leakage in accordance with the requirements of Sections R402.1 through R402.4.4. Q R402.4.1 Building thermal envelope. The building thermal envelope shall comply with Sections R402.4.1.1 and R402.4.1.2.The sealing methods between dissimilar materials shall allow for differential expansion and contraction. • R402.4.1.1 Installation.The components of the building thermal envelope as listed in Table R402.4.1.1 shall be installed in accordance with the manufacturers instructions and the criteria listed in Table 402.4.1.1,as applicable to the method of construction. Where required by the code official,an approved third party shall inspect all components and verify compliance. • R402.4.1.2 Testing. The building or dwelling unit shall be tested and verified as having an air leakage rate of not exceeding 5 air changes per hour in Climate Zones 1 and 2,and 3 air changes per hour in Climate Zones 3 through 8.Testing shall be conducted with � a blower door at a pressure of 0.2 inches w.g.(50 Pascals).Where required by the code official,testing shall be conducted by an approved third party A written report of the results of the test shall be signed by the party conduc6ng the test and provided to the code official.Testing shall 6e perFormed at any time after creation of all penetrations af the building thermal envelope. During testing: 1.Exterior windows and doors,fireplace and stove doors shall be closed,but not sealed,beyond the intended weatherstripping or � other infiltration control measures; � 2.Dampers including exhaust,intake,makeup air,backdraft and flue dampers shall be closed,but not sealed beyond intended I � infiltration control measures; 3.Interior doors,if installed at the time of the test,shall be open; 4.Exterior doors for continuous ventilation systems and heat recovery ventilators shall be closed and sealed; 5.HeaGng and cooling systems,if installed at the time of the test,shall be turned off;and 6.Supply and return registers,if installed at the time of the test,shall be fully open. j O R402.4.2 Fireplaces.New wood-buming fireplaces shall have tight-fitting flue dampers and outdoor combustion air I O R402.4.3 Fenestration air IeakageWindows,skylights and sliding glass doors shall have an air infiltration rate of no more than 0.3 cfm � per square foot(1.5 L/s/m2),and swinging doors no more than 0.5 cfm per square foot(2.6 L/s/m2),when tested according to NFRC 400 or ' AAMAlWDMA/CSA 10111.S.2/A440 by an accredited,independent laboratory and listed and labeled by the manufacturer. Exception: Site-built windows,skylights and doors. � O R402.4.4 Recessed lighting. Recessed luminaires installed in the building thermal envelope shall be sealed to limit air leakage between conditioned and unconditioned spaces.All recessed luminaires shall be IC-rated and labeled as having an air leakage rate not more than 2.0 cfm(0.944 L/s)when tested in accordance with ASTM E 283 at a 1.57 psf(75 Pa)pressure differential.All recessed � luminaires shall be sealed with a gasket or caulk between the housing and the interior wall or ceiling covering. � � R403.1.1 Thermostat provisfon(Mandatory).At least one thermostat shall be provided for each separate heating and cooling system. I I � R403.1.3 Heat pump supplementary heat(Mandatory).Heat pumps having supplementary electrio-resistance heat shall have controls � that,except during defrost,prevent supplemental heat operation when the heat pump compressor can meet the heaUng load. � I � R403.2.2 Sealing(Mandatory}411 ducts,air handlers,and filter boxes and building cavities that form the primary air containment ' I passageways for air distribution systems shall be considered ducts and plenum chambers,shall be constructed and sealed in accordance � � with Section C403.2.7.2 of the Commercial Provisions of this code and shall be shown to meet duct tightness criteria by post-construction i or rough-in testing below. Duct tightness shall be verified by testing to Section 803 of the RESNET Standards by either an energy rater certified in accordance with Section I 553.99,Florida Statutes,or as authorized by Florida Statutes,to be"substantially leak free"by either of the following: i 1. Post-construction test:Total leakage shall be less than or equal to 4 cfm(113 L/min)per 100 square feet(9.29 m2)of conditioned floor area i when tested at a pressure differential of 0.1 inches w.g.(25 Pa)across the entire system,including the manufacturers air handler enclosure.All register boots shall be taped or otherwise sealed during the test. � 2. Rough-in test:Total leakage shall be less than or equal to 4 cfm(113 Umin)per 100 square feet(9.29 m2)of conditioned floor area when tested � at a pressure differential of 0.1 inches w.g.(25Pa)across the system,including the manufacturers air handler enclosure.All registers shall be , i taped or otherwise sealed during the test.If the air handler is not installed at the time of the lest,total leakage shall be less than or equal to 3 cfm � (85 L/min)per 100 square feet(9.29 m2)of conditioned floor area. i Exceptions: � 1 The total leakage test is not required for ducts and air handlers located entirely within the building envelope. � 2. Duct testing is not mandatory for buildings complying by Section R405 of this code. 5/12/2017 1:38 PM EnergyGauge�USA-FlaRes2014 -Section R405.4.1 Com Page 1 of 3 I