Laserfiche WebLink
IN�STALLATION AND MAINTENANCE INSTRUCTIONS �`� S'ySTEM � <br /> � � <br /> lr�r��v�n, '� �� SENSOR o <br /> W <br /> RTS2, RTS2�A�5� A�S 3825 Ohio Avenue,S[.Charles,Illinois 60174 <br /> 1-800-SENSOR2,FAX:630-377-6495 <br /> Mu�t�-Signaling Accessory www.systemsensor.com <br /> SPECIFICATIONS <br /> Dimensions: 4.8"W x 5.3"H x 1.6"D (12.2cm W x 11.9 cm H x 3.8 cm D) <br /> Weight: 0.35 Ib. (160 g) <br /> Operating Voltage: 20-29 VDC <br /> Power Requirements <br /> Standby: 3.0 mA ma�c. <br /> TYouble: 16.0 mA m� <br /> Alarm w/o strobe: 30 mA ma�c <br /> Alarm with strobe: 55 mA maac <br /> Connections: Strip terminal,14 AWG to 22 AWG wire � <br /> Wiring Distance: 1000 Feet From Duct Smoke Detector <br /> Sounder: 85 dBA at ten feet <br /> Temperature: 14°F to 140°F(-10°C to 60°C) <br /> Humidity: 95% relative humidity;non-condensing <br /> Listing: UL 268 and ULC 5529-02 <br /> Notice:This manual should be left with the owner/user of this equipment. <br /> GENERAL INFORMATION FIGURE 1: <br /> The National Fire Protection Association (NFPA) has published codes, stan- <br /> dards,and recommended practices for the installation and use of this product. <br /> It is recommended that the installer be familiar with theses requirements,with <br /> local codes,and any special requirements of the local authority having juris- <br /> diction. For further information,consult NFPA 72 and 90A requirements. <br /> The System Sensor RTS2 and RTSZ-AOS multi-signaling accessories are de- ��O�� <br /> signed for use with System Sensor InnovairFlex 4-wire com�entional duct <br /> smoke detectors only.The accessory has two bicolored LEDs that indicate the <br /> sensor status of up to two connected duct smoke detectors. The key switch <br /> on the unit can be used to select a connected duct detector sensor(either sen- <br /> sor 1 or sensor 2),and the selected sensor can be tested or both sensors can � �� <br /> be reset simultaneously using the test/reset butron. LED status indications � �� <br /> include:Standby (green blink),1Youble (amber),Maintenance (amber blink) - �� <br /> ^� -� <br /> and Alarm(red). � <br /> With the key switch selected,there is also the capability of obtaining a sen- p��S§�RES�T O O <br /> sitivity measurement of the selected sensor using the SENS-RDR sensitivity p�OLD/T�ST <br /> reader(sold separately). S�NSOV@ <br /> SPECIFIC FEATURES OF THE RTS2 AND RTS2-AOS INCLUDE: <br /> • Standby (Green Blink), TYouble (Amber), Maintenance (Amber Blink) � <br /> and Alarm (Red) LEDs to indicate detector status <br /> • Keyswitch to select desired sensor, enable test/reset button and <br /> sensitivity reading <br /> �O PLOY �AINY <br /> • Test/reset button <br /> • Sensitivity reading ability with SENS-RDR(sold separately) <br /> • Selectable continuous or temporal tone <br /> AOS-Add-On-Strobe (included on RTS2-AOS mode]) H0621-00 <br /> • Provisions for single-or double-gang box mounting <br /> • Ability to discretely monitor two sensors when duct smoke detectors <br /> are configured in a 2-to-1 set up (See InnovairFlex duct smoke detector <br /> manual for reference.) <br /> CONTENTS <br /> 1 RTS2 or RTS2-AOS Multi-Signaling Accessory <br /> 1 Mounting Hardware Kit(Contains (2)sets of mounting screws and(1) tam- <br /> per resistant outer cover mounting screw <br /> I <br />� SS-310-00 1 156-3381-003 <br />