17-18897 - Laserfiche WebLink

Browse Search

I . . - _�°�-_ _ _"` b ,�_ ` y ` + w + ��I�� ��, �� 4. � . Continue upslope in a similar manner,maintaining minimum 3-inch side-laps and minimum 6-inch end-laps. F�sten 6- ' ' inch o.c.in the laps and 12-inch o.c.in two,equally spaced,staggered center r,oU�s in the field. Ensure all end laps are staggered at least 3 feet aparE. One the same day,install LibertyT"'SBS Self-Adhering Base/PIy;StormGuard°Film Surfaced Leak earrier;UnderRoo�`"'2 Polyester-Surfaced Leak Barrier; UnderRoo�"' HT High Teinperature Leak Barrier;WeatherWatch° Mineral Surfaced Leak Barr•ier or WeatherWatch°XT Mat Surfaced Leak Barrier overthe StormSafeT"'Anchor Sheet, 6.6 RoofPro�'"SBS-Modified Al!-Purpose Underlavmenfi and Shin�le�Mate°Roof Deck Protec�ion: 6.6.1 Install RoofProT"° and Shingle-Mate° in compliance with manufac�urer's published instaliation inseructions and the requirements for ASTM D2Z6,Type I and ll underlayments in FBC Sections 1507 forthe type o;prepared roofcovering to be instalied. A double layer is required for 2:12<roof slope<4:12. No hammer tacks or staples are permitted. 6.6.2 Optional, or if required by the Authority Having lurisdiction: Instafl a leak barrier of Li6ertyTM SBS Self-Adhering Base/Ply Sheet;StormGuard° Film Surfaced Leak Barrier;UnderRootTM'2 Polyester-Surfaced Leak Barrier;UnderRoof�"' HT High Temperature Leak Barrier; WeatherWatch° Mineral Surfaced Leak Barrier or WeatherWatch° XT Mat Surfaced Leak Barrier at vulnerable leak areas,including but not lirnited to eaves,valleys,rakes,skylights and dormers. At eaves and valleys, install the leak barrier prior to installation of the underlayment. Along fhe rake,install the underlayment,leaving 6 to 8-inch of the deck exposed, and then install the•leak barrier over the underfayment and exposed decking. At oiher areas,install the leak barrier over the underlayment. 6.7 VersaShield°Fire-Resistanfi Roof Deck'Protection: 6.7.1 Install VersaShield° Fire-Resistant Roof Deck Protectlon in compliance with.manufacturer's published installation � instructions and the requiremenfis for ASTM D226,Type I and II or ASl'M D4869 underlayments in FBC Sections 1507 for the t}/pe of prepared roof co�ering to be installed. A double layer is required for 2:12<roof slope<4;12. No hammertacks ors�aples are permitted, 6.7.2 Optional, or if required by the Authority Having Jurisdiceion: install a leak barrier of LibertyT"" SBS Self-Adhering Base/Ply Sheet;StormGuard°Flm SurFaced Leak Barrier;UnderRoof""2 Polyester-Surfaced Leak Barrier;UnderRoofr"' HT High Temperature Leak Barrier; WeatherWatch° Mineral Surfaced Leak Batrier or WeatherWatch° XT Mat - � Surfaced Leak Barrier at vulnerable leak areas,including but not limited to eaves,valleys,rakes,skylighfis and dormers. At eaves and valleys, install the leak barrier prior to inscallation of the underlayment. Along the rake,install the - underlayment,leaving 6 to 8-inch of the deck exposed, and then install the leak barrier over the underlayment and exposed decking. At other areas,insta(1 the leak barrier over fihe underlayment. 7, BUILDIIVG PERMIT DiEQUIREMEiVTS: As required bythe Building Official orAuthor"rty HavingJurisdiction in orderto properly evaluate the installation ofthis product. 8. MANUFACTURING PLANTS: � Contact the manufac�urer orthe named QA entity for information on plants covered under Rule 61G20-3 QA requirements. 9, CtUALITY ASSURAMCE ENTI.lY: UL,LLC.—QUA9625;(847}664-3281 -EiVD OF EVALUATION REPORi'- Exterior Research and Design,LLC. Evaluation Report 01506.03.12-R5 F115487-RS Certificate ofAuthorizofion#9503 Revision 5:0�/OZ/2015 Page 5 ot 5