17-19173 - Laserfiche WebLink

Browse Search

TFP11�0 � Page 4 of 6 Frame Sprinkler Finish K Type Ra ng Color Natural Chrome Lead Wax Wax Over Code Brass Plated Coated Coated Lead Coated Pendent(TY3211) 165°F(74°C) Unpainted 1 2 3 and 212°F(100°C) White 1,2,3,5 5.6 Upright(TY3111) 1/2" 280°F(138°C) Blue 1,2 4 N/A NPT Recessed Pendent 165°F(74°C) Unpainted 1,2,3,5 (TY3211 w/Style 20) 212°F(100°C) White 1,2,3,5 N/A 165°F(74°C) Unpainted 1,2,3 Pendent(TY4211) 212°F(100°C) White 1,2,3 280°F(138°C) Blue 1,2 4 N/A 8.0 165°F(74°C) Unpainted 3/4" 1,2,3 NPT Upright(TY4111) 212°F(100°C) White 1,2,3,5 280°F(138°C) Blue 1,2 4 N/A Recessed Pendent 165°F(74°C) Unpainted (TY4211 w/Style 30) 1�2�5 N/A 212°F(100°C) White Pendent(TY4911) '165°F(74°C) Unpainted 1,2,3 and 212°F(100°C) White 1,2,3,5 8�� Upright(TY4811) I 1/2" 280°F(138°C) Blue 1,2 N/A N PT Recessed Pendent '165°F(74°C) Unpainted (TY4911 w/Style 20) 1�2 N/A 212°F(100°C) White OTES: UL Listed . C-UL Listed . FM Approved . FM Approved for maximum 150°F(68°C)ambient temperatures . LPCB Approved(LPCB Ref.No.094a/03) N/A:NotAvailable TABLE A LABORATORY L/STINGS AND APPROVALS After installation, the sprinkler color coded wax is to be used, and Step C. After the ceiling has been wrench flats and frame arms must retouching of wrench flats and frame installed or the finish coat has been be inspected and the wax coating arms is only permitted at the time applied, slide on the Style 20 or 30 retouched (repaired) whenever the of initial sprinkler installation. With Closure over the Series TY-L Sprin- coating has been damaged and bare tf►e steel rod heated as previously kler and push the Closure over the metal is exposed.The wax coating on described, touch the rod to the area Mounting Plate until its flange comes the wrench flats can be retouched by requiring additional wax with the rod in contact with the ceiling. gently applying a heated 1/8 in. diam- angled downward, and then touch the eter steel rod to the areas of wax that wax stick to the rod approximately one- � have been damaged, to smooth it half inch away from the area requiring back over areas where bare metal is retouching. The wax will melt and run exposed. down onto the sprinkler. Series TY-L Recessed Pendent � Sprinklers Installation Only retouching of the wax coating The Series TY-L Recessed Pendent applied to the wrench flats and frame Sprinklers must be installed in accor- arms is permitted, and the retouching dance with this section. is to be performed only at the time of Step A. After installing the Style 20 the initial sprinkler installation. or 30 Mounting Plate, as applicable, The stee/rod should be heated only over the sprinkler threads and with to the point at which it can begin to pipe thread sealant applied to the pipe melt the wax,and appropriate precau- threads,hand tighten the sprinkler into tions need to be taken, when handling the sprinkler fitting. the heated rod, in order to prevent the Step B. Tighten the sprinkler into the installer from being burned. sprinkler fitting using only the W Type If attempts to retouch the wax coating 10 Recessed Sprinkler Wrench (Ref. with complete coverage are unsuc- Figure 8).With reference to Figure 1,2, cessful,additional wax can be ordered or 3,the W Type 10 Recessed Sprinkler in the form of a wax stick (the end of Wrench is to be applied to the sprinkler ' which is color coded).Only the correct wrenching flanges.