Laserfiche WebLink
'\,/TR1 IT(j ER® <br /> 17. For adhesive-applied membrane systems,side laps shall be minimum 3-inch wide sealed with min.1.5-inch heat weld. Unless otherwise noted,membrane adhesive application rates areas follows: <br /> Membrane Adhesive - Method Rate <br /> EverGuard TPO EverGuard TPO#1121 Bonding Adhesive Contact(both sides) 0.8 to 1.0 gal/square/surface. For use over SECUROCK Gypsum-Fiber Roof Board,the application rate <br /> (#1121) changes to 1.2 to 1.67 gal/sq/surface <br /> To polyisocyanurate or Structodek High Density Fiberboard Roof Insulation,Fiber Base HD1 or Fiber Base HD6 <br /> EverGuard TPO EverGuard WB181 Bonding Adhesive(WB181) Contact(both sides) at 0.63 gal/square and roof cover underside at 0.21 gal/square. To Dens Deck Prime or SECUROCK Gypsum- <br /> Fiber Roof Board at 0.63 to 0.75 gal/square and roof cover underside at 0.21 to 0.25 gal/square <br /> EverGuard TPO VOCr,uard Low VOC TPO Bonding Adhesive(L- Contact(both sides) 0.46 gal/square/surface <br /> EverGuard TPO 3 Square Low VOC Bonding <br /> EverGuard TPO Adhesive(TPO 3-Square) Contact(both sides) 0.84 gal/square/surface <br /> EverGuard TPO FB Ultra Hot asphalt Wet lay(substrate) 25 Ibs/square <br /> EverGuard TPO FB Ultra EverGuard WB381 Bonding Adhesive(WB181) Wet lay(substrate) 0.83 to 1.0 gal/square <br /> GAF LRF Adhesive M-(LRF-M) or LRF Adhesive 1-inch wide ribbons spaced as noted in tables herein. Note:The adhesive ribbons are located directly over <br /> EverGuard TPO FB Ultra O(LRF-0) Wet lay(substrate) the adhesive ribbons used to secure the insulation when the cover is bonded to insulation less than 1.5-inch <br /> thick. <br /> EverGuard TPO FB Ultra GAF 2-Part Roofing Adhesive(GAF 2-Part) Wet lay(substrate) "Spatter pattern"at 3.75 Ibs/sq. <br /> EverGuard TPO FB Ultra OlyBond 500 Canister Wet lay(substrate) "Spatter pattern"at 0.32 gal/square. <br /> 18. The"Triposite Roofing System"noted herein consists of loose-laid GAFGLAS Stratavent Perforated Venting Base Sheet,followed by asphalt-applied two(2)plies of Ruberoid 20 Smooth or three(3)plies of GAFGLAS <br /> FlexPly 6,followed by asphalt-applied 80-mil EverGuard TPO FB Ultra with i-5/8"heat welded side laps. <br /> 19. Unless otherwise noted,the"Hybrid Roofing System"noted herein consists of asphalt-applied Ruberoid 20 Smooth, Ruberoid Mop Smooth, Ruberoid Mop Smooth 1.5,GAFGLAS#75 Base Sheet,Tri-Ply#75 Base <br /> Sheet or GAFGLAS#80 Ultima Base Sheet followed by asphalt-applied EverGuard TPO FB Ultra. <br /> 20. EverGuard Extreme TPO may be used as an alternate to EverGuard TPO. EverGuard Extreme TPO FB Ultra may be used as an alternate to EverGuard TPO FB Ultra. <br /> 21. The following insulations are interchangeable within the scope of this Evaluation Report. <br /> ➢ EnergyGuard Polyiso Insulation b EnergyGuard NH Polyiso Insulation; <br /> —EnergyGuard Ultra Polyiso Insulation b EnergyGuard NH Ultra Polyiso Insulation; <br /> ➢ EnergyGuard HD Polyiso Insulation b EnergyGuard NH HD Polyiso Insulation; <br /> ➢ EnergyGuard HD Plus Polyiso Insulation b EnergyGuard NH HD Plus Polyiso Insulation. <br /> Exterior Research and Design,I.L.C.d/b/a Trinity ERD Evaluation Report 01506.12.13-1-R15 for F1.16730-1114 <br /> Certificate of Authorization#9503 6`h EDITION(2017)FBC HVHZ EVALUATION Revision 15:10/17/2017 <br /> Prepared by: Robert Nieminen,PE-59166 EverGuard TPO Single-Ply Roof Membrane Systems;(800)766-3411 Appendix 1,Page 4 of 84 <br />