18-20357 - Laserfiche WebLink

Browse Search

• StarLink radio trouble 'Input (from StarLink radio PC 3/4G radios where an External Antenna needs to be in- board PGM1 terminal to detect StarLink radio trouble) stalled outside of the room in which the radio is installed • Requires a sealed lead acid min 4AH /max 7AH battery (maximum 30 meters in Residential applications), please for minimum 24-hour standby time (max charge current use RF Transmitter Board 9GPS53320EXAPSLD availa- 200mA). ble from our Customer Service Department, if not provid- • Trouble relay output (C, N/O and N/C terminals) to ed. The 9GPS53320EXAPSLD is identified by ".two red wire to a panel zone dedicated to "GSM Trouble" (dry dots" located on the lower right corner of the board. See contacts). Remove jumper"J2"to isolate common from WI2222 included with the 9GPS53320EXAPSLD for the ground simple installation procedure. . • Green AC ON LED visible from the exterior housing GEM-Tamperkit - Tamper switches and screws to protect • Yellow TROUBLE LED on PC board. Flashes signify: metal housing (see page 19). One flash:AC fail/brownout(2 hour delay) Two flashes: Low battery SPECIFICATIONS Three flashes: Charging circuit trouble The following specifications apply to all StarLink radio mod- Four flashes: StarLink radio trouble els unless otherwise stated: The housing-mounted transformer (when provided) is Electrical Ratings for 120VAC, 60Hz mounted inside its own housing compartment with a re- For Models with Power Supply placeable UL Listed .5A fast blow primary fuse. 120VAC • Input Voltage: 120VAC nominal connections are to be made by a licensed electrician using • Input Current: 150mA maximum suitable connectors, in accordance with N.E.C. and local e Maximum Charging Current: 200mA code requirements. Electrical Ratings for+12V For Models without Power Supply* ADDITIONAL COMPONENTS • Input Voltage: 11-15VDC (power-limited output from In addition to the models listed above, the following sub- Listed control panel). Note: Models SLE3/4G-CFB and assemblies are available: SLECDMA-CFB are rated 11-25VDC input. SLE-ULPS-R - Power Supply. Required for installations • Input Current: 71mA with peak RF transmission current where the control panel cannot provide the 71 mA of of 200mA. Auxiliary power required to operate the StarLink radio. Electrical Ratings for the IN 1 Burg/Fire Input: Uses a standard 4AH / 12V minimum (7AH maximum) Input Voltage: 9-15VDC. Note: Models SLE3/4G-CFB rechargeable battery to provide radio standby power. and SLECDMA-CFB are rated 9-25VDC input. Requires connection to either the model NAPCO Maximum Input Current: Up to 2mA from FACP NAC TRF12/T123 (16.5V/20VA) external plug-in transformer circuit or the chassis-mounted 16.5VAC / 20VA transformer Electrical Ratings for IN 2 and IN 3: affixed inside the housing (see wiring diagrams further in Maximum Loop Voltage: 15VDC. Note: Models this manual). Note: For models without the SLE-ULPS- SLE3/4G-CFB and' SLECDMA-CFB are rated max R, connect the radio terminals 1 and 2 to the control 25VDC input. panel Aux Power terminals(observing polarity). SLE-DLCBL- Download Cable, 6 feet. Maximum Loop Current: 1.2mA • End of Line Resistor(EOLR)Value: 10K(2 req'd) SLE-ANTEXT - Extended antenna with 15 feet of cable Electrical Ratings for 3 PGM Outputs: (any suitable external cellular antenna is permitted by UL). Always follow the manufacturer's installation .in- structions. Note: Antennas are not Listed by UL. For active; 15V maximum when not active. Note: Models SLE3/4G-CFB and SLECDMA-CFB are rated max NOTICE TO AUTHORITIES HAVING JURISDICTION, USERS, INSTALLERS, DEALERS, AND OTHER AFFECTED PARTIES FIRE PROGRAMMING OPTION PERMITTED IN AVAILABLE SETTINGS REQUIRED UL 864 SETTINGS UL8647(Y/N) Disabled(Jumper 1 installed). Also required for Commercial/Burgla- Unattended Remote Downloading No Enable/Disable ry installations. Note: See page 8"Configuration Download 1 Firm- ware Updates"for jumper instructions. Unsupervised using conduit within 20 feet of FACP(default). If not IN2 and IN3 Unsupervised Yes Supervised/Unsupervised using conduit,install Jumpers 4 and 5 and EOL Resistors(see pages 3 and 4). 7 Day Supervision,Radio to NOC No 200 seconds,5 minutes, 200 seconds,5 minutes,60 minutes 60 minutes,7 days `For Commercial Fire installations,a UL Listed Fire Alarm regulated power supply or FACP regulated auxiliary output is required. 2 StarLink'SLE Commercial Series Alarm Communicators--Installation Instructions