Laserfiche WebLink
467 Swan Ave • Hohenwald,TN 38462 • (800) 284-7437 • www.olivertechnologies.com • Fax (931) 796-8811 <br /> OLIVER TECHNOLOGIES,INC. <br /> FLORIDA INSTALLATION INSTRUCTIONS FOR THE <br /> MODEL 1101 "V"SERIES ALL-STEEL FOUNDATION SYSTEM <br /> ENGINEERS STAMP ENGINEERS STAMP <br /> 1.SPECIAL CIRCUMSTANCES:If the following conditions.occur-STOPI Contact Oliver Technologies at 1-800-284-7437: <br /> c)Roof eaves exceed 1.6" e)Location is within 1500 feet of coast <br /> a)Pier height exceeds 48" d)Sidewall height exceed 96". <br /> b)length of home exceeds 76' <br /> INSTALLATION OF GROUND PAN <br /> 2.Remove weeds and debris in an approximate two foot square to expose firm,soil foreach ground pan(C). <br /> 3.Place ground pan(C)directly below chassis I-beam.Press or drive pan firmly into soil until flush with or below soil. <br /> SPECIAL NOTE:The longitudinal"V"brace system,serves as a pier under the home and should be loaded as any other pier. <br /> It is recommended that after leveling piers,and one-third inch(1/3")before home is lowered completely on to piers,complete <br /> steps 4 through 9 below. <br /> INSTALLATION OF LONGITUDINAL"V"BRACE SYSTEM <br /> NOTE:WHEN INSTALLINGTHE LONGITUDINAL SYSTEM ONLY,A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOILTEST PROBE SHOULD BE <br /> USED TO DETERMINE CORRECTTYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBE TEST READINGS ARE BETWEEN 175&275 A 5 FOOT ANCHOR MUST <br /> BE USED.IF PROBETEST READINGS ARE BETWEEN 276&350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WITH DIAGONALTIES AND <br /> STABILIZER PLATES EVERY 5'4".VERTICALTIES ARE ALSO REQUIRED ON HOMES SUPPLIED WITH VERTICALTIE CONNECTION POINTS(PER FLORIDA REG.). <br /> 4.Choose one of the approved longitudinal tube installations;either Diagram A or B.Then select the correct square tube(E)length from the <br /> diagram for appropriate pier height at support location or cut and drill 1.5"square tube to achieve appropriate length. <br /> PIER HEIGHT': 1.25" 1.50" PIER HEIGHT 1.50" <br /> (40°Min.- 45°Max.) Tube Length Tube Length 9/16"Dia.(.562'1 hole (40°Min.- 60°Max.) Tube Length <br /> 7,34"to 25 -_. :.. 22" 18" 14"to 18" :207: <br /> 24 3/4'•'fo 32.1 /4". . :_, 32":: ::.. 7 8 ' :, I 1 18"to 25 :.. 28" <br /> 33='to,41"__„ ..,... _._ .:-._.:44'; 18':: _,..., 24"to.35'• <br /> 40 to.48' 54 18" 30"to 40" 44" <br /> Diagram A o.�s� 7, .36"to 48,, :.,:. s.:,. 54 <br /> Diagram B <br /> 5.Install(2)of the 1.50"square tubes(E{18"tube})into the"U"bracket(J),insert carriage bolt and leave nut loose for final adjustment. <br /> 6.Place I-beam connector(F)loosely on the bottom-flange of the I-beam. <br /> 7.(For Diagram A installation)Slide the selected 1.25"tube(E)into a 1.50"tube(E)and attach to I-beam connectors(F)and fasten loosely <br /> With bolt and nut.(For Diagram B installation)Attach the selected 1.5"tubes(E)to the I-beam connectors(F)and fasten loosely with bolts <br /> and nuts. <br /> 8.Repeat steps 6 through 7 to create the"V"pattern of the square tubes loosely in place. <br /> 9.Using standard hand tools tighten all nuts and bolts.(For Diagram A installation only,secure 1.25"and 1 .50"tubes using <br /> four(4) 1 /4"-14 x 3/4"self-tapping screws in pre-drilled holes.) <br /> �+°cooar�:®Qtf <br /> ... 61 <br /> m tSa ••• <br /> • o. Q242 <br /> STATE OF lY <br /> PATENT#6634150&OTHER PATENT PENDING °�teec+e++°° Pagel <br />