Laserfiche WebLink
AD USTA � E SWI EL RIiNG ANGER= <br /> FUNCTION: Designed for the suspension of non-insulated stationary pipe lines.The <br /> knurled insert nut that allows a vertical adjustment after installation,is a iFg.141 & 1t4y1Fill'I li <br /> topped to NFPA reduced rod size standards. Fig.141F has a layer of felt N¢FPA SWIVEIL f <br /> which separates the pipe from the hanger to reduce vibration and sound. to I <br /> APPROVALS: Uiiderivriters'Laboratories listed and Factory Mutual approved Fig.141 IZ�IIN�i HANCiE�It <br /> %"to 8"sizes only.Complies with Federal Specification A-A-1192A(Type <br /> 10),Manufacturers'Standardization Society SP-69(Type 10)and NFPA Fig. 141 PRE-GALVANIZED <br /> standards for reduced rod sizes. <br /> Fig. 141F PRE-GALVANIZED <br /> ORDERING: Specify pipe size and figure number. WITH FELT LINING <br /> Rod <br /> Pipe Sae. "Adj. Max.Rec.Wt. Each <br /> Size B D E. Load/lbs. (inlbs.): -` <br /> A C t <br /> 1/2 % 1 7/e 17/16 23/4 31/16 300 .10 <br /> 3/4 % 111/16 11/e 21/2 31/16 300 .10 <br /> 1 % 1 15/8 1 21/2 33/16 300 .10 1 C <br /> 11/4 % 115/16 11/16 213/16 39/16 300 .11 �� I B <br /> 11/2 % 21/s 1'/16 3'/s 37/6 300 .11 �' + <br /> 2 % 27/16 11/8 35/16 4% 300 .14 �� D <br /> 2'/z % 23/a 1'/a 311h6 5 525 .19• i E <br /> 3 % 27/e 11/e 33/4 59/16 525 .23 ; <br /> 31/2. % 33/e 1% 45/16 65/16 525 .25 <br /> 4 3/8 37/e 11/2 41/2 7 650 .30 <br /> 5 '/z 45/e 1% 5% 8% 1000 .50 <br /> 6 '/z 5% 21/4 61/2 913/16 1000 .58 <br /> 8 '/z 613/1s 21/16 r 715/1s 12'/a 1000 .90 O <br /> FM �L <br /> Note: If ordering Fig.141F felt lined hangers for pipe sizes of 3'/Z"or under,order the next <br /> argest size to allow for the thickness of the felt lining. MATERIAL: Low carbon steel <br /> FUNCTION: Designed for the suspension of non-insulated stationary pipe lines.The <br /> aJ Fir 1�5L1 & 1►51F " j' <br /> knurled insert nut,allows for vertical adjustment after installation. <br /> Fig.151F has a layer of felt which separates the pipe from the hanger to �1� SWIVE9L <br /> reduce vibration and sound. <br /> APPROVALS: Underwriters'Laboratories listed and Factory Mutual approved Fig.151 RI�N ` HA�NGEiIZ <br /> 21/z"to 8"sizes only.Complies with Federal Specification A-A-1192A <br /> (Type 10),and Manufacturers'Standardization Society SP-69(Type 10). Fig. 151 PRE-GALVANIZED <br /> ORDERING: Specify pipe size and figure number. Fig. 151F PRE-GALVANIZED <br /> WITH T LINING <br /> Rod <br /> Pipe Size . Adj.. Max.Rec.Wt.Each _Ff—� <br /> Size A B C. :. p E:. Load/Ibs. (in Ibs.) `_.. <br /> 21/2 1/z 23/4 11/4 311/16 51/s 600 .33 ✓ :. fY.. <br /> 3 '/z 31/e 11/e 4 57/e 600 .35 f <br /> 31/2 '/z 1 3% 11/2 45/16 65/e 600 .37 <br /> 4 % 37/e 11/a 415/16 71/e 1000 .48 <br /> 5 % 43/e 13/6 55/e 81/2 1000 .57 <br /> y <br /> 6 3/4 55/16 2 611/16 101/e 1250 1.06 <br /> 8 3/4 615/16 1 2% 85/16 1 127/8 1250 1.32 f <br /> Note: I{ordering Fig.151F elt lined hangers or pipe sizes of Yh or under,order the next <br /> argest size to allow for the thickness of the felt lining. <br /> a r r a VL <br /> MATERIAL: Low carbon steel <br /> PHD Manufacturing, Inc. •44018 Columbiana-Waterford Road • Columbiana, OH 44408 <br /> Toll Free(800)321-2736•Phone: (330)482-9256•Fax: (330)482-2763•www.phd-mfg.com <br />