19-21506 - Laserfiche WebLink

Browse Search

L-Series Specifications General L-Series standard horns.strobes,and horn strobes shall mount to a standard 2 x 4 x 1 '/--inch back box.4 x 4 x V/2-inch back box,4-inch octagon back box.or double-gang back box.L-Series compact products shall mount to a single-gang 2 x 4 x 17,-inrlh back box.A universal mounting plate shall be used for mounting ceiling and wall products for all standard models and a separate universal mounting plate shall be used for mounting wall compact models.The notification appliance circuit wring shall terminate at the universal mounting plate.Also,L-Series produces.when used with the Syric-Circuit"Module accessory.shall be powered from a non-coded notification appliance circuit output and shall operate on a norninal 12 or 24 volts.When used with the Sync-Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts:24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-:wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15,30,75,95, 110,135.and 185. Strobe The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync-Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/16 x 21,,8-inch back box.The module shall also control two Style Y(class 8)circuits or one Style Z(class A)Circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules-together will synchronize all the zones they control.The module shall not operate on a coded power supply. Standard Operating Temperature 32'F to 120'F(O'C to 49'C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC or regulated 24 DC/FWR1.2 Operating Voltage Range 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range IVIDU Sync Module 8.5tol7.5V(12V nominal)orl6.5to33V(24Vnominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6-L x 4.7-W x 1.91""D(143 mrn L x 119 mm W x 49 mm D) Compact Wall-Mount Dimensions(including lens) 5.26"L x 3.46"W x 1.91"D(133 mm L x 88 mm W x 49 mm D) Horn Dimensions 5.6"L x 4.7-W x: 1.25"D(143 mm L x 119 mm W x 32 mm D) Compact Horn Dimensions 5.25" L x 3.45' W x 1.25"D(1 33mm L x 88mm W x 32mm D) 1.Full Wave Rectified(FWR)voltage is a non-regulated.time-varying power source that is used on some power supply and panel outputs. 2.Strobe products will operate at 12 V nominal only for 15 cd and 30 cd.