19-21653 - Laserfiche WebLink

Browse Search

s ",,J"'TRINITYI ER® 4. PRODUCT DESCRIPTION: This Evaluation Report covers Norandex Vinyl Siding Systems in a variety of profiles and surface textures/ colors. This evaluation is limited to the specific product trade names referenced in this report subject to the Installation Requirements and Limitations/Conditions of Use herein. Brand Product Profiles Thickness . American Classic American Classic Insulated Siding System D4,D5DL,D6 0.044" Cambridge Beaded 6.5 Beaded 0.048" Finish Works Board&Batten 0.044" Generations Thermal Core Siding D4,D5DL,D6 0.044" Great Barrier D4,D5DL 0.044" Polar Wall Plus! D4,D5DL,D6 0.044" Norandex Sagebrush D4,D5DL 0.050" Shenendoah 6.5 Semi-Beaded 0.048" Shenendoah T3 0.040" Sterling D4,D5,D5DL 0.044" Summit Manor D4,D4.5,D4.5DL 0.040" Woodsman Select D4,D4DL,D5,D5DL 0.042" 5. LIMITATIONS: 5.1 This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This evaluation report is not for use in FBC HVHZ jurisdictions. 5.3 Refer to FBC 1405.14 for prescriptively permitted installations based on the wind speed (Vasd),wall-height and Exposure for the project and its location. For installations and/or locations exceeding the prescriptively allowable installations,limitations relating to design wind pressure resistance are outlined in Appendix 1. 5.3.1 "MDP" = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of project-specific design wind pressures. The MDP for the selected installation shall meet or exceed the design wind pressure requirement for the project for each pressure zone. 5.3.2 Tables are based on wall cladding design wind pressure requirements in accordance with ASCE 7-10, multiplied by 0.6 (Pa,d)for allowable loads. 5.3.3 Use of Appendix 1 is limited to siding installations with sheathing on enclosed buildings (GCpi_±0.18), no load combinations (Kd = 1) and site conditions and location of the structure that do not meet all conditions specified in Section 26.8.1 of ASCE 7-10 (K,t= 1.0) at the stated maximum height. Analysis for buildings falling outside these constraints shall be on a project-by-project basis by a Florida Registered P.E. 5.3.4 Reference to "OK" indicates the system performance exceeds project requirements for that particular zone. Reference to"NO"indicates additional testing is required. 5.3.5 The dimension of Zones 4 and 5 (interior and end zones) shall be defined as 10% of the least horizontal plan-view dimension or 40% of the mean roof height, whichever is smaller, but not 15 j less than either 4% of the least horizontal plan- 5 4 9 ® a view dimension or 3 feet, as outlined in Figure o 0 30.4-1 of ASCE 7-10. 5 s Exterior Research and Design,I.I.C. Evaluation Report C13820.04.09-1-R3 Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION F1.12500-113 Norandex Vinyl Siding Systems;(517)780-3185 Revision 3:09/26/2017 Page 3 of 4