Laserfiche WebLink
Firestone <br /> TECHNICAL INFORMATION SHEET BUILDING PRODUCTS <br /> UltraPlyTm Bonding Adhesive <br /> s <br /> Item Description Item Number � <br /> Bonding Adhesive W56TP03005 <br /> 'Firestone. <br /> Ultra <br /> Ply' <br /> 9onaing Adhesive_ <br /> !vSt PO.3005 <br /> -,z T,-w <br /> . .ro.:ooe <br /> Product • • " <br /> Description: <br /> Firestone UltraPly Bonding Adhesive is a solvent based contact adhesive designed specifically for bonding Firestone <br /> UltraPly TPO membranes to approved insulations in addition to wood, metal, masonry and other acceptable substrates. <br /> Note: Not for use in adhering UltraPly TPO XR membranes. <br /> Method of Application: <br /> 1. Surfaces to receive Firestone UltraPly Bonding Adhesive must be clean, smooth, dry, and free of sharp edges, loose <br /> and foreign materials, oil, grease, and other contaminants. <br /> 2. Stir the adhesive thoroughly to achieve a uniform mix with no sediment on the bottom and no marbling evident <br /> before and during use. <br /> 3. Apply UltraPly Bonding Adhesive at about the same time to both the exposed underside of the sheet and the <br /> substrate to which it will be adhered so as to allow approximately the same drying time. Apply UltraPly Bonding <br /> Adhesive evenly avoiding areas of accumulation. <br /> 4. Apply the UltraPly Bonding Adhesive with a solvent resistant paint roller, and roll the adhesive onto the mating <br /> surfaces. When applying UltraPly Bonding Adhesive, ensure complete uniform coverage of both surfaces that will be <br /> adhered. Care must be taken not to apply Bonding Adhesive over seam areas. <br /> 5. UltraPly Bonding Adhesive can be dispensed by means of power rollers or industrial spray equipment. Other <br /> equipment may be used as recommended by the manufacturer for application of this adhesive. Note: Spray applied <br /> bonding adhesive requires back- rolling with 9"(228.6 mm)wide solvent resistant roller(medium nap)to insure 100% <br /> coverage of the adhesive on the substrate and membrane. <br /> 6. Allow Bonding Adhesive to flash off until tacky. Touch down on the Bonding Adhesive surface with a clean, dry <br /> finger to be certain that the adhesive does not string. As you are touching the adhesive, pushing straight down to <br /> check for stringing, also push forward on the adhesive at an angle to ensure that the adhesive solvents have flashed <br /> off and are ready throughout its thickness. If either motion exposes wet areas or sticking when the finger is lifted, <br /> then it is not ready for mating. Flash off time will vary depending on ambient conditions. <br /> 7. Starting at the fold, roll the previously coated portion of the sheet into the coated substrate slowly and evenly so as to <br /> minimize wrinkles. <br /> 8. To ensure proper contact, compress the bonded half of the sheet to the substrate with a stiff push broom using <br /> heavy pressure immediately after mating. <br /> 9. Contact your Firestone Technical Coordinator at 1-800-428-4511 for specific application information. <br /> Storage: <br /> • Store in original unopened containers at temperatures between 60 OF - 80 OF (16 °C-27 °C) until ready for use. <br /> • For optimum results, rotate your stock to ensure stored material has not exceeded the shelf life of one year. <br /> Firestone Building Products I Sales:(800)428-4442 1 Technical(800)428-4511 1 www.firestonebpco.com <br /> S723-RFS-059 TIS#808 12/10/2013 <br /> Page 1 of 3 <br />