Laserfiche WebLink
BASE-FLASHING CAP SHEET <br /> VERAL ALUMINUM fdplast' <br /> Commercial Product Data Sheet <br /> Product Description COMMERCIAL PRODUCT INFORMATION <br /> Veral Aluminum is a high performance, foil clad, modified Unit: Roll <br /> bitumen finish ply designed for use in multi-layer modified <br /> bitumen roof systems. Veral Aluminum consists of a Coverage: 1.0 Square (9.3 m2) <br /> fiberglass scrim/fiberglass mat composite impregnated and <br /> coated with high quality styrene-butadiene-styrene (SBS) Coverage Weight <br /> modified bitumen and surfaced with a protective aluminum foil Per Square: Min: 96 lb (4.6 kg/m2) <br /> facing. <br /> Product Uses <br /> Roll Length: Min: 33.5 ft (10.21 m) <br /> Veral Aluminum is the finish ply of the Siplast Veral Roof Roll Width: Avg: 3.28 ft (1.00 m) <br /> System, and is lapped 3 inches (7.6 cm)side and end. The <br /> Siplast Vera[System is preferably applied by torching but can Thickness: Avg: 150 mils (3.8 mm) <br /> be applied in approved Type IV asphalt subject to Siplast Min: 146 mils (3.7 mm) <br /> specifications and requirements. Siplast Veral Roof Systems <br /> are used over most roof decks with drainage. Selvage Surfacing: Release Tape <br /> Veral Aluminum is the standard flashing sheet in all Top Surfacing: Continuous Aluminum Foil <br /> guaranteed Siplast Roof Systems, Vera] Aluminum flashing <br /> sheets are cut to size off the end of the roll and applied <br /> vertically, always working to a selvage edge. Contact Siplast Back Surfacing: Silica Parting Agent <br /> for specific approval on other product uses. <br /> Product Approvals Packaging: Rolls are wound onto a compressed paper tube. <br /> Veral Aluminum Is approved by FM Approvals (FM Standard The rolls are placed upright on the selvage edge on pallets <br /> 4470) for use in Veral Class 1 insulated steel deck cushioned with corrugated cardboard and are adhered with <br /> constructions and insulated and non-insulated concrete roof adhesive at the labels. The top of the palleted rolls is covered <br /> deck constructions,subject to FM conditions and limitations. with Kraft paper. The palleted material is protected by a heat <br /> shrink polyethylene shroud. <br /> Vera]Aluminum is classified by Underwriters Laboratories for <br /> use in cULus Classified Siplast Veral Roof Systems. Siplast Pallet: 41 Number Rolls <br /> X 48 in(104 cm X 122 cm)wooden pallet <br /> Veral Roof Systems have been classified by Underwriters s Per Pallet: 23 <br /> Laboratories as Class A roofing systems over non- Number Pallets Per Truckload: 18 <br /> combustible, insulated non-combustible, combustible, and Minimum Roll Weight: 96 lb(43.5 kg) <br /> insulated combustible decks. <br /> Storage and Handling: All Siplast roll roofing products should <br /> Vera[meets or exceeds the requirements of ASTM D 6298 for be stored on end on a clean flat surface. Care should be <br /> SBS-modified bituminous sheet materials using foil facing. taken that rolls are not dropped on ends or edges and are not <br /> stored in a leaning position. Deformation resulting from these <br /> Veral Aluminum is certified by the U.S. EPA as an ENERGY actions will make proper installation difficult. All roofing should <br /> STAR'Roof Product. be stared in a dry place, out of direct exposure to the <br /> elements, and should not be double stacked. Material should <br /> Siplast Roof Systems also have received the approval of many be handled in such a manner as to ensure that it remains dry <br /> regional and local authorities. Please contact Siplast for prior to and during installation, <br /> specific information as required. <br /> Rev 2/2018 <br /> ALUMINUM SURFACED CAP SHEET <br /> TORCH APPLIED <br /> Current copies of all Siplast Commercial Product Data Sheets are <br /> posted on the Siplast Web site at www.Siplast.com. <br /> Siplast 1000 Rochelle Blvd. 201 Bewicke Ave.,Suite 208 Customer Service in North America <br /> Irving,TX 75062-3940 North Vancouver,BC,Canada V7M 3M7 1,800,922.8800 www.siplast.com <br />