20-22543 - Laserfiche WebLink

Browse Search

DN-60686:A1 UDACT 2 N OT I F I E R° Universal Digital Alarm Communicator Transmitter . by Honeywell Annunciator Control System General The Universal Digital Alarm Communicator Transmitter(UDACT 2)is designed for use on Notifier Fire Alarm Control Panels and on the NCA-2 Network Control Annunciator.When used in con- junction with the NCA-2 network control annunciator, the ` UDACT2 can report the status of all'control panels on NOTI•FIRE•NETTm.The UDACT-2 transmits system status to UL - listed Central Station Receivers via the public switched tele- phone network.The UDACT 2 can be installed in the panel cab- • - inet or remotely in a separate enclosure. u. - NOTE. The UDACT-2 can also be used with legacy panels. Please refer to the UDACT-2 manual for more information. The UDACT2 .upload/download programming 'and firmware - updates are accomplished with VeriFire Tools. Refer to the Pro- gramming Section for further.details. • The UDACT-2 is capable of transmitting the status of software zones (Alarm and Trouble), System Trouble, Panel Off-Normal, Supervisory; Bell Trouble, Low Battery, and AC Fail. They UDACT2 is capable of transmitting all of the zone and point sta- tus associated with each panel. When the UDACT-2 is used with the NFS-3030, NF82-3030, and NCA-2 it is capable of reporting-up to 2,040 points.Report- ing may be in the form of points or zones(refer to the UDACT-2 manual.for specific reporting parameters). Points transmitted may be programmed for a variety of types,including fire,water- flow,supervisory,etc. 'UDACT-2 NOTE.Descriptions regarding point capacity,-listed above,are for receivers which-receive in Ademco Contact ID format. See chart . Open Collector relay driver for Total Communications Failure on page 2 for compatible receivers. or UDACT-2 trouble. Features • Real-time clock. • Extensive transient protection. • Programmable with VeriFire Tools version 6,60 or higher, . EIA-485 interface to host panel. allowing the UDACT2 programming to be uploaded/down- loaded and saved. Programming • Maximum of 14-point trouble messages transmitted per hour. The UDACT-2 programming is created and downloaded using • Dual phone lines with line voltage detect. VeriFire Tools.This enables the unit to be programmed prior to • Compact in size:.6.75"x 4.25"(17.145 x 10.195 cm). installation, be easily modified, and saved.either online or • USB port for upload/download programming. offline. A printed report with point or zone in can be Manual Test Report function. generated from VeriFire Tools for an ONYX Series panel or net-, work annunciator.The point report consists of the central station • Manual Transmission Clear function. point address,ACS point,ACS point function,panel label,panel • Mounts in a separate enclosure(ABS-8136 or UBS-1 B/R). point,type code,custom and extended label,alarm verification, • Communicates vital system status including: walktest participation,presignal,and PAS information.The zone —Independent zone fire alarm. report consists of a grid with the central station point address, ACS point address, source, ACS point function, custom label —Independent zone non-fire.alarm. and panel label.This report may be sent to the Central Station —Independent zone trouble. for their records. VeriFire Tools also supports upgrading the -Independent zone supervisory. UDACT-2 operating firmware. —AC(mains)Power Loss(programmable). —Low Battery and Earth Fault. —System Off-Normal. —12 or 24 hour test signal. —Abnormal Test Signal per new UL requirements. —EIA-485 Communication Bus Failure. • Annunciation of UDACT-,2 Troubles including: loss of phone lines, communication failure with either Central Station,total communications failure. • Individual LEDs for: Power, EIA-485 Loss, Manual Test, Kis- soff, Comm Fail, Primary Line Seize, Secondary Line Seize and Modem Communications. DW60686:A1 4/2/12—Page 1 of 2