20-22543 - Laserfiche WebLink

Browse Search

DN-6724:83 FCM-1 (A) & FRM-1 (A) NOT 1 F 1 E R° Series Control and Relay Modules by Honeywell Intelligent Addressable Devices General FCM-1(A)Control Module: The FCM-1(A)Addressable Con-- trol.Module provides Notifier intelligent fire alarm control pan- els a circuit for Notification Appliances (horns, strobes, speakers,etc.).Addressability allows the FCM-1(A)to be acti- vated; either manually or through panel programming, on a .. select(zone or area of coverage)basis. .�.� FRM-1(A)Relay Module: The FRMA(A) Addressable Relay "'E•'"""''` Module.provides the system with a dry-contact output for acti- vating a variety of auxiliary devices, such as fans, dampers, control equipment,etc.Addressability allows the dry contact to be activated, elther.manually or through panel programming, on a select basis. FlashScan®.(U.S.Patent 5,539,389)is a communication pro- tocol developed by .NOTIFIER Engineering that greatly y.. enhances the speed of communication between analog intelli- gent devices: Intelligent devices. communicate in a grouped fashion. If one of the devices within the group,has new infor- mation,the panel CPU stops the group poll and concentrates on single points.The net effect is response speed greater than five times that of other designs. FCM-1(A) Features • Built-in,type identification automatically identifies these The FCM-1(A)is configured.for a single Class B(Style Y)or devices to the control panel: Class A(Style Z)Notification Appliance Circuit. • Internal circuitry and relay powered directly by two-wire The FRM-1(A) provides two Form-C dry contacts that SLC loop.The FCM-1(A)module requires power(for horns, switch together. strobes,etc:),or audio(for speakers). • Integral LED "blinks" green each time a communication is Operation, received from the control panel and turns on in steady red Each FCM-1(A)or FRM-1(A)uses one of 159 possible module when activated. addresses on a SLC loop (99 on CLIP loops). It responds to. • LED blink may be deselected globally(affects all devices). regular polls from the control panel and reports its type and High noise immunity(EMF/RFI). status, including the open/normal/short status of its Notifica- tion Appliance Circuit (NAC). The LED blinks with each poll The FCM-1(A) may be used to switch 24-volt NAC power,. . • audio(up to A) may be received. On command, it activates its internal relay. The FCM=1(A)supervises Class B (Style Y) or Class A (Style Z) • 'Wide viewing angle of LED. notification or control circuits. • SEMS screws with clamping plates for wiring ease. Upon code command from the panel, the FCM-1(A) wily dis • Direct-dial entry of address 01— 159 for FlashScan loops, connect the supervision and connect the external power sup- 01 —99 for CLIP mode loops. ply in the proper polarity across the load device. The Speaker, and audible/visual applications may be wired for disconnection of the supervision provides a positive.indication Class B or A(Style Y or Z). to the panel that the control relay actually turned ON.*The external power supply is always relay isolated from the com'- Applications munication loop so that a trouble condition on the external power supply will never interfere with the rest of the system. The FCM-1(A)'is used to switch 24 VDC audible/visual power, Rotary switches set a unique address for each module. The high-level audio (speakers). The FRM-1(A) may be pro address may be set before or after mounting. The built-in. grammed to operate dry contacts for applications such as door TYPE CODE(not settable)will identify the module to the con- holders or Air Handling Unit shutdown, and to reset four-wire trol panel,so as to differentiate between a module and a sen- smoke detector power. sor address. NOTE.Refer to the SLC Manual(PN 51253)for details regarding releasing applications with the FCM-1(A).Refer to the FCM-I-REL Specifications for FCM-1(A) datasheet(DN-60390)for new F/ashScanO releasing applications. Normal operating voltage: 15 to 32 VDC. Construction Maximum current draw: 6.5 mA(LED on). • The face plate is made of off-white heat-resistant plastic. Average operating current: 350 pA direct poll,375 pA group • Controls include two rotary switches for direct-dial entry of poll with LED flashing, 485 pA Max. (LED flashing, NAC address(01-159). shorted.) DN-6724:B3.2/17/2011—Page 1 of 2