20-22543 - Laserfiche WebLink

Browse Search

a L-Series Specifications General System Sensor L-Series chimes and chime strobes shall mount to a standard 4 x 4 x 11/z-inch back box,4-inch octagon back box,single- gang 2 x 4 x 11/8-inch back box,or double-gang back box.A universal mounting plate shall be used for mounting products.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,System Sensor L-Series products,when used with the Sync•Circuit Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Syno•Circuit Module,12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC,or full-wave rectified,unfiltered power supply.Chime strobes shall have field-selectable candela settings of 15,30,75,95,110,135,and 185 for wall units and 15,30,75,95,115,150,and 177 for ceiling units. Chime Strobe Combination The chime strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1638 and UL 464.The chime strobe shall comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The chime shall have two audibility options and an option to switch between temporal three pattern,non-temporal(continuous)pattern, 1 second chime pattern, 1/4 second chime pattern,5 second whoop chime pattern.These options are set by a multiple position switch. Synchronization Module The module shall be a System Sensor Sync-Circuit listed to UL 464 and shall be approved for fire protective service.The module shall synchronize SpectrAlert strobes at 1 Hz and all available chime.tones.Also,while operating the strobes,the module shall silence the chimes on chime/strobe models over a single pair of wires.The module shall mount to a 411/16 x 4"/16 x 2 1/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard OperatingTemperatu're 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12VDC or regulated 24DC/FWR1 Operating Voltage Rangez 8 to 17.5V(12V nominal)or 16 to 33V(24V nominal) Operating Voltage Range with MLD3 8.5 to 17.5V(12V nominal)or 16.5 to 33V(24V nominal) Input terminal wire gauge 12 to 18 AWG Chime strobe dimensions(including lens) 5.6 in L x 4.7 in W x 1.91 in D(143 mm L x 119 mm W x 49 mm D) Chime dimensions 5.6 in L x 4.7 in W x 1.25 in D(143 mm L x 119 mm W x 32 mm D) Ceiling Chime strobe dimensions(including lens) 6.8"Dia.x 2.47"D(173.5mm Dia.x 62.7mm D) SBBRL(red wall surface mount back box) 5.6 in L x 4.7 in W x 4.3 in D(142 mm L x 119 mm W x 109 mm D) SBBWL(white wall surface mount back box) 5.6 in L x 4.7 in W x 4.3 in D(142 mm L x 119 mm W x 109 mm D) SBBCRL(red ceiling surface mount back box) 6.9"Dia.x 2.5"D(175.8mm Dia.x 63.5mm) SBBCWL(white ceiling surface mount back box) 6.9"Dia.x 2.5"D(175.8mm Dia.x 63.5mm) Notes: 1.Full Wave Rectified(FWR)voltage is a non-filtered,time varying power source that is used on some power supply and panel outputs. 2.CHS products will operate at 12 V nominal only for 15 and 30 cd. UL Current Draw Data UL Max.Chime Current Draw(mA RMS) 6-17.5 Volts 16-33 Volts Sound Pattern dB DC DC FWR 1 Second Chime High 5 8 9 1 Second Chime Low 5 8 9 1/4 Second Chime High 6 10 10 1/4 Second Chime Low 5 9 9 Temporal Chime High 7 10 10 Temporal Chime Low 6 9 9 5 Second Whoop High 12 15 16 5 Second Whoop Low 7 10 11 Coded High 12 15 16 'This data represents coding at 3 chimes per second.Actual current draw will vary depending upon coding selected.