Laserfiche WebLink
467 Swan Ave s Hohenwald,TN 38462 • (800) 284-7437 • www.olivertechnologies.com o Fax (931) 796-8811 <br /> OLIVER TECHNOLOGIES,INC. <br /> FLORIDA INSTALLATION INSTRUCTIONS FOR THE <br /> MODEL 1101 "V"SERIES ALL STEEL FOUNDATION SYSTEM <br /> MODEL 1101"V"(Steps 1-14) <br /> LONGITUDINAL ONLY:Follow Steps 1-9 <br /> LATERAL ONLY:Follow Steps 1-3 and Steps 10-14 <br /> ENGINEERS STAMP FOR CONCRETE APPLICATIONS:Follow Steps 15-18 ENGINEERS STAMP <br /> 1.SPECIAL CIRCUMSTANCES:If the following conditions Occur-STOP!Contact Oliver Technologies at 1-800-284-7437: <br /> a)Pier height exceeds 48" Q Roof eaves exceed.16" e)Location is within 1500 feet of coast <br /> b)length of home exceeds 76' d)Sidewall height exceed 96" <br /> INSTALLATION OF GROUND PAN <br /> 2.Remove weeds and debris in an approximate two foot square to expose firm soil for each ground pan(C). <br /> 3.Place ground pan(C)directly below chassis I-beam.Press or drive pan firmly into soil until flush or below soil then install pier per <br /> manufacturer's instructions or per Florida Regs. <br /> SPECIAL NOTE:The longitudinal W".brace system may also serve as a pier under the home and should be loaded as any other pier. <br /> It is recommended that after leveling piers,and one-third inch(1/3")before home is lowered completely on to piers,complete <br /> steps 4 through 9 below then remove jacks. <br /> INSTAf 606N OF LONGITUDINAL"V"BRACE SYSTEM(Model 1101 L"V'J <br /> NOTE:WHEN INSTALLING THE LONGITUDINAL SYSTEM ONLY,A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOILTEST PROBE SHOULD BE <br /> USED TO DETERMINE CORRECTTYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBETEST READINGS ARE BETWEEN 175&275 A 5 FOOT ANCHOR MUST <br /> BE USED.IF PROBETEST READINGS ARE BETWEEN 276&350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WITH DIAGONAL TIES AND <br /> STABILIZER PLATES EVERY 5'4".VERTICALTIES ARE ALSO REQUIRED ON HOMES SUPPLIED WITH VERTICALTiE CONNECTION POINTS(PER FLORIDA REG.). <br /> 4.Choose one of the approved longitudinal tube installations;either Diagram A or B.Then select the correct square tube(E)length from the <br /> diagram for appropriate pier height at support location or cut and drill 1.5"square tube to achieve appropriate length. <br /> PIER HEIGHT 1.25" 1.50" PIER HEIGHT 1.50" <br /> (49'Min.- 450 Max.) Tube Length Tube Length 9t16'Dia.(.s 2-?hole (40°Min.- 60"Max.) Tube Length <br /> 7 3/4"to 25" 22" 18" 14":to 18°,' <br /> 0.75' _ <br /> 243/4"'to32.1'i4" 32" 18":; j 18"_to25" 28" <br /> 33"to 4.1." � 1.81124°.ta 35,"::.,.._ 391': <br /> 40"to.48° 54", 1$": .. Part E 30"to 40" <br /> Diagram A oas'� <br /> Diagram B <br /> 5.Install(2)of the 1.50"square tubes(E)into.the"U"bracket(J),insert carriage bolt and leave nut loose for final adjustment. <br /> 6.Place I-beam connector(F)loosely on the bottom flange of the I-beam. <br /> 7.(For Diagram A installation)Slide the selected 1.25"tube(E)into a 1.50"tube(E)and attach to I-beam connectors(F)and fasten loosely <br /> with bolt and nut.(For Diagram B installation)Attach the selected 1.5"tubes(E)to the I-beam connectors(F)and fasten loosely with bolts <br /> and nuts. <br /> 8.Repeat steps 6 through 7 to create the"V"pattern of the square tubes loosely in place. <br /> 9.Using standard hand tools tighten all gluts and bolts.(For Diagram A installation only,secure 1.25"and 1 .50"tubes using <br /> four(4)1 /4"-14 x 3/4"self-tapping screws in pre-drilied holes.) <br /> INSTALLATION OF LATERAL TELESCOPING TRANSVERSE ARM SYSTEM(Model 1101 T"V") <br /> THE MODEL 1101"V"(LONGITUDINAL&LATERAL PROTECTION)ELIMINATES THE NEED FOR STABILIZER PLATES&FRAME TIES. <br /> NOTE:THE USE OF THIS SYSTEM REQUIRES VERTICALTIES SPACED AT T47: <br /> FOUR FOOT(4')GROUND ANCHOR MAY BE USED EXCEPT WHERE THE HOME MANUFACTURER SPECIFIES DIFFERENT. <br /> 10.Install remaining vertical tie-down straps and 4'ground anchors per home manufacturer's instructions.NOTE:Centerline anchors <br /> to be sized according to soil torque condition.Any manufacturer's specifications for sidewall anchor loads in excess of 4,000 lbs. <br /> require a 5'anchor per Florida Code. <br /> 11.Select the correct square tube brace(H)Length for set-up lateral transverse at support location.The lengths come in either 60"or <br /> 72"lengths.(With the 1.50"tube as the bottom tube,and the 1.25"tube as the inserted tube.) <br /> 12. Install the 1.50 transverse brace(H)to the ground pan connector(D)with bolt and nut. <br /> 13. Slide 1:25"transverse brace into the 1.50"brace and attach to adjacent I-beam connector(I)with bolt and nut. <br /> 14.Secure 1.50"transverse arm to 1.25"transverse arm using four(4)1/4"-14 x 3/4"self-tapping screws in pre-drilled holes. Paae I <br /> PATENT#6634150&OTHER PATENT PENDING Revision 08/23/18 <br />