|
D9412GV4 Control.Panql
<br /> substitution features and provides enhanced security Access granted
<br /> with encryption.The B420, DX4020 and ITS-DX4020-G No entry
<br /> can all be used for remote programming. Request to enter
<br /> GV4 is the first Security Control panel to support DNS Request to exit
<br /> (Domain Name System) for both remote programming Wireless interface
<br /> and central station communication. DNS provides ease The B820 SD12 Inovonics Interface Module connects
<br /> of use, eliminating the need to use static IP addresses an Inovonics EN4200 Serial Receiver to the control
<br /> as your reporting destination and accommodates a panel SD12 bus, allowing this UL Listed wireless
<br /> simple solution for central station disaster recovery. system to be programmed locally via the panel keypad,
<br /> IP Setup is available via the installer keypad menus as well as remotely through RPS.
<br /> and the remote programming software, eliminating the
<br /> need to use complicated internet programming tools Event log
<br /> such as ARP and Telnet. The event log stores up to 1,000 local and transmitted
<br /> events. The event log includes time, date, event, area,
<br /> Communication paths point, user number, and transmission status. View the
<br /> The control panel accommodates up to four separate event log from a keypad or use RPS to remotely
<br /> destinations for primary, alternate, and backup retrieve event information. RPS operators can retrieve
<br /> receivers for automatic test reports. events periodically using one call, rather than receiving
<br /> When resetting alarms or arming or disarming a several calls each day. When the event log reaches a
<br /> system, the user is identified by name and number. programmed threshold of stored events, it can send an
<br /> Firmware updates optional report to a receiver.
<br /> Remote firmware updates using the RPS Firmware Fire test
<br /> Update wizard through the IP connection (B426/B420 When a user activates Fire Test Mode, the control
<br /> Connetix Ethernet Communication Module) as well as panel suppresses all reports to the central station. The
<br /> an on-site flash update key, provides for easy feature keypad and annunciator show all testing data. An
<br /> enhancements without replacing ROM chips. automatic sensor reset feature saves time; you do not
<br /> *For GV4 version 2.00 firmware update information, need to reset the sensors manually. At the end of test,
<br /> refer to the, "GV4 version 2.00 firmware updates" the keypad shows the number of untested points.
<br /> datasheet to learn more about key enhancements, Programming dia nostics and controls
<br /> and supported products. g g� g
<br /> Installers can program locally or remotely through RPS
<br /> A wide variety of input options as well as basic keypad programming. A programmable
<br /> Each point: system passcode prevents unauthorized remote
<br /> • Accommodates normally-open (NO) and programming.
<br /> normally-closed (NC) devices with end-of-line (EOL)
<br /> resistor supervision. — Two data buses
<br /> • Is programmable for fire, fire supervisory, or intrusion GV4 provides 2 data buses which support a wide array
<br /> application. of components. The SDI bus supports keypads,
<br /> • Can be hard-wired, addressable, or wireless. access, and communications modules and also allows
<br /> Security and Fire detection connection of existing components in a retrofit
<br /> The control panel provides eight on-board points, and application. The new SD12 bus supports input and
<br /> up to 238 additional off-board points. You can program output devices as well as a new wireless interface
<br /> individual points to monitor all types of burglar alarms, module, and an Ethernet communicator. SD12 allows
<br /> fire alarms, and supervision devices. these devices to be mounted up to 1000 ft (305 m)
<br /> from the control panel, providing installation
<br /> Scheduled events (SKEDS) convenience and flexibility.
<br /> The internal clock and calendar start individually
<br /> scheduled events (SKEDS). SKEDS perform functions Commercial Fire Alarm support
<br /> such as arm or disarm, relay control, or point Suitable for Commercial Fire (UL 864, 91h Edition)
<br /> bypassing. The D9412GV4 Control Panel offers: applications.
<br /> • 40 scheduled events with up to 25 different functions Bosch Video Management System integration
<br /> • Eight opening windows and eight closing windows With Bosch Video Management System (Bosch VMS)
<br /> • Eight user windows and an intrusion system, the VMS operator has a single
<br /> • Day-of-week, date-of-month, or holiday only schedules user interface to monitor and control the intrusion
<br /> • Four holiday schedules of 366 days each (leap year) system combined with video surveillance. With Bosch
<br /> Access control VMS and a control panel, the operator can, for
<br /> The control panel provides custom door strike, point example:
<br /> shunt and auto disarming response by area. There are View videos triggered by intrusion events, including
<br /> 14 panel-wide access levels with both manual and all relevant information such as areas, point, and user
<br /> scheduled control. show in the display with the event
<br /> Store, view, or print access events such as:
<br />
|