Laserfiche WebLink
0 • 0 <br /> FS-ONE <br /> High Performance Intumescent <br /> Firestop Sealant <br /> Product description �t <br /> ■ Intumescent(expands when exposed to fire)firestop sealant that <br /> helps protect combustible and non-combustible penetrations for <br /> up to 4 hours fire rating <br /> Product features <br /> ■ Smoke,gas and water resistant after material has cured <br /> ■ Contains no halogen,solvents or asbestos <br /> ■ High fire rating properties --- - <br /> ■ Water based,easy to clean ;_Technical Data* __ _FS-ONE <br /> ■ Protects most typical firestop penetration applications chemical basis Water-based intumescent acrylic <br /> ■ Paintable dispersion <br /> ■ Single component systems available color Red <br /> ■ Meets LEEDTM requirements for indoor environmental quality credit Application temperature 40OF to 1040F(5°C to 40°C) <br /> 4.1 Low Emitting Materials,Sealants and Adhesives and 4.2 Paints Skin forming time Approx.20-30 min. <br /> and Coatings Curingtime Approx.2 mm/3 days <br /> Areas of application Average volume shrinkage 24.1% <br /> ■ Steel,copper and EMT pipes (ASTM C1241) <br /> ■ Insulated steel and copper pipes Movement capability Approx.5% <br /> ■ Cable bundles Expansion rate(unrestricted) Up to 3-5 times original volume <br /> ■ Closed or vented plastic pipes Temperature resistance(cured) -40OF to 212OF(-40'C to 100°C) <br /> Surface burning characteristics Flame Spread:0 <br /> ■ HVAC penetrations (ASTM E 84-96) Smoke Development:5 <br /> For use with Sound transmission classification 56(Relates to specific construction) <br /> ■ Concrete,masonry,drywall and wood floor assemblies (ASTM E 90-99) <br /> ■ Wall and floor assemblies rated up to 4 hours Tested in accordance with <br /> •UL 1479 •ASTM E 814 •ASTM E 84 •ASTM G21 <br /> Examples At 73'F(23'C)and 50%relative humidity <br /> ■ Sealing around combustible pipe penetrations in fire rated <br /> ea1F FILL,E IN OR CAVITY MATERIAL <br /> construction rFo FOR USE IN THROUGH-PENETRATION FM FOG <br /> ■ Sealing around non-combustible penetrations in fire rated c�us FIRESTOP SYSTEMS <br /> SEE UL FIRE RESISTANCE DIRECTORY APPROVED <br /> construction 66Y7 Visit tbcryste patlble.c <br /> F6.-,satr de ,kof <br /> Ne Lubnzol Corporation. <br /> Installation instructions for FS-ONE <br /> Notice 4. Smoothing of firestop sealant:To complete the On materials where oil,plasticizers or solvents may <br /> • Before handling,read Material Safety Data Sheet seal,tool immediately to give a smooth appearance. bleed i.e.impregnated wood,oil based seals,green <br /> and product label for safe usage and health Excess sealant,prior to curing,can be cleaned away or partially vulcanized rubber <br /> information. from adjacent surfaces and tools with water. In any penetration other than those specifically <br /> • Instructions below are general guidelines—always 5. Leave completed seal undisturbed for 48 hours. described in this manual or the test reports <br /> refer to the applicable drawing in the UL Fire 6. For maintenance reasons,a penetration seal could Storage <br /> Resistance Directory or Hilti Firestop Systems Guide be permanently marked with an identification plate. <br /> for complete installation information Store only in the original packaging in a location <br /> P In such a case,mark the identification plate and protected from moisture at temperatures between <br /> Opening fasten it in a visible position next to the seal. 40'F(5°C)and 86'F(30'C) <br /> 1. Clean the opening.Surfaces to which FS-ONE will Not for use Observe expiration date on the packag <br /> be applied should be cleaned of loose debris,dirt, High movement expansion joints <br /> oil,moisture,frost and wax.Structures supporting Underwater <br /> penetrating items must be installed in compliance <br /> with local building and electrical standards. <br /> Application of Firestop sealant E aV i s�.iJ <br /> 2. Install the prescribed backfilling material type and <br /> depth to obtain the desired rating(if required).Leave <br /> sufficient depth for applying FS-ONE. <br /> _ 3. Application of firestop sealant:Apply FS-ONE to the 1.Clean opening. 2.Pack mineral wool. 3.Apply FS-ONE. 4.Smooth 5.Leave completed 6.Fasten Identification. <br /> required depth in order to obtain the desired fire rating. (if required) FS-ONE, seal undisturbed for plate(d required). <br /> q P g• 48 hours. <br /> Make sure FS-ONE contacts all surfaces to provide - <br /> maximum adhesion.For application of FS-ONE use a I <br /> standard caulking gun,foil pack gun,bulk loader and I <br /> bulk gun.With FS-ONE buckets,Greco type sealant 4 <br /> pumps may be used.(Contact pump manufacturer for <br /> proper selection). l <br /> 1.Clean opening. 2.Pack mineral wool. 3.Apply FS-ONE. 4.Smooth 5.Leave completed 6.Fasten identification <br /> (if required) FS-ONE, seal undisturbed for plate(f required). <br /> 48 hours. <br /> Hilti. Outperform. OuVast. <br /> Hilti,Inc.(U.S.)1-800-879-8000•www.us.hilti.com•en espanol 1-800-879-50RaOPFiliestop Systems Guide <br />