20-887 - Laserfiche WebLink

Browse Search

INSTALLATION DETAILS FOR INTEGRAL FIN&J-CHANNEL FRAMES INSTALLATION OPTION 6 INSTALLATION OPTION 5 ANCHORED THROUGH FRAME ANCHORED THROUGH INTEGRAL FIN INTO 2X WOOD FRAME OR INTO RX WOOD FRAME OR EDGE DISTANCE INSTALLATION OPTION 5 EMBEDMENT BUUK51 KIP.SEE NOTE 2,THIS BUCKSTRIP.SEE NOTE 2,THIS SHEET. ANCHORED THROUGH INTEGRAL EMBEDMENT SHEET. FIN INTO ZX WOOD FRAME OR (11l114"MAX SHIM 16 1/4'MAX SHIM BUCK-STRIP,SEE NOTE 2,THIS EDGE DISTANCE SHEET. TYP.ANCHOR TYPE, VISIBLE 17 J-CHANNEL EMBEDMENT AND EDGE_ 00 18 LIGHTWIDTH FRAME DISTANCE PER SUBSTRATE, SHOWN SEE TABLE 2,SHEET 2. BALANCE 44 TYPE BOTTOM EMBEDMENT VARIES SASH Lj 114"MAXSHIM 42 WITH BASH TYP.ANCHOR TYPE, EDGE WEIGHT 54 30 EMBEDMENT AND EDGE DISTANCE n I — 31 —1 DISTANCE PER SUBSTRATE, TOP SEE TABLE 3,SHEET 2. 0 SASH TYP.ANCHOR TYPE, 18 (MAIL SHOWN) INTEGRAL EMBEDMENT AND EDGE 85 a 0 II�� VISIBLE FIN DISTANCE PER SUBSTRATE, LIGHT WIDTH ME SEE TABLE 3.SHEET 2. J-CHANNEL w D 1 SHOWN (NAIL SHOWN) FRAME 9) 87 EXTERIOR 73 19 20 OPT.SASH TOP NOTES- SHOWN BUCK WIDTH LIFT lu VISIBLE 1)USE ONLY HORIZONTAL SECTION C-C LIGHT i 9 SUBSTRATE-APPROPRIATE HEIGHT ANCHORS LISTED ON TABLES 2&3 48 OF SHEET 2.FOLLOW EMBEDMENT FBc COMPLIANT ALUMINUMISTEEL FRAMING OR STEEL STUD, 21 WMAX. SHEET 2. FORALL AND EDGE DISTANCE LIMITS.ANY I SHIM MAY BE VERTICAL OR HORIZONTAL.SEE SUBSTRATE PROPERTIES.TABLES 2&3, WINDOWS:I INSTALLATION OPTION SHOWN MAY 22 ANCHOR@ BE D... ON ANY SIDE OFTHE ALSO FOR DADS-APPROVED 3.56'FROM WINDOW. END ANDAT #10 OR#12 STEEL 1 W MAX• 45 46 47 CENTER. 2)MASONRY ANCHORS MAY BE SELF-DRILLING SHIM BUCK FOR USED INTO WOOD AS PER TABLE 2, SMS(G5),SEE HEIGHT WINDOWS SHEET 2.ALL WOOD BUCKS LESS TABLES 2&3. 50 16 OVER 36" THAN 1-112"THtCK ARETO BE SHEET2. MM ADD CONSIDERED IX INSTALLATIONS. EXTERIOR 30 ADDITIONAL IX WOOD BUCKS ARE OPTIONAL IF SCREWS UNIT Is INSTALLED DIRECTLY TO @16-313- SUBSTRATE.WOOD BUCKS VISIBLE FROM END. DEPICTED AS 2X ARE i-112"THICK 66 LIGHT OR GREATER.IX AND 2X BUCKS HEIGHT (WHEN USED)SHALL BE DESIGNED FIN AND/OR TO PROPERLY TRANSFER LOADS FLANGE REMOVED (2) 16 TESTED UNIT TO THE STRUCTURE.WOOD BUCK IN-FIELD INTERIOR DESIGN AND INSTALLATION IS THE 0 WEEP 64 LOCATION:6-518" RESPONSIBILITY OF THE ENGINEER INTEGRAL FIN NOTCHES AT 63 FROM SASH END. OR ARCHITECT OF RECORD. FRAME SHOWN EACH END. 31 3)VISIBLE LIGHT WIDTH OR HEIGHT INSTAL TION EXTERIOR IN TALLATION PRODUCT REVISED .27'X 125" 7 30 (ALSO REFERRED TO AS DAYLIGHT OPTION 7 10, ANCHORED THROUGH FRAME INTO EE 38 OPENING)IS MEASURED FROM OPTION 8 as Bu=lying with the Florida WEEPH Code W1CCVER@ TYP.ANCHOR TYPE,EMBEDMENT AND BEADING TO BEADING. ANCHORED THROUGH HOA-No. 20-0401.05 2.87FROM EDGE DISTANCE PER SUBSTRATE,SEE INTEGRAL FIN INTO METAL METAL(INTEGRAL FINIFLANGE REMOVED) — EACH END. TABLE 3,SHEET 2.(SCREW SHOWN) 011111", — ReW.fb. — Expiration Bte09/1712025 1/4"MAX "'% 0�kY LYNAI"'// C)REVISED DADE MULLION By 9*— INTEGRAL FIN �/" GEN Mlamt-Dade Product Control SHIM G N SHOWN NOTE. FRAME SHOWN 7 VN VISIBLE LIGHT FORMULAS z*:: No.68705 AK-3/11/20 No ANCHORS REQUIRED IN WIDTH D-.fpu-. Dr— FRAME SILL IF ANCHORING T @SASH:BUCK WIDTH-610 J ROSOWSKI @ FIXED LITE:BUCKWIDTH-7-10 Lo 107oTEcHNoLoGyDRivE J-CHANNEL&INTEGRAL FIN FRAMES THROUGH THE FRAME. 1,3 93 --� N.VENICE,FL 34275 INSTALLATION OPTION 5 EDGE DISTANCE HEIGHT(EQUAL-LITE) A EOF l7tf.: -1600(941Y480 INSTALLATION-NI 05/15/15 ANCHOREDTHROUGH BUCK HEIGHT/2-"$" DOUBLE HUNG WINDOW IN Rm INTEGRAL FIN INTO ZX WOOD--I EMBEDMENT ///,, I AL Suf-/Vom.' sccdw. ShoeC brazing No. FRAME OR BUCK-STRIP.SEE VERTICAL SECTION D-D A 4 M11YER' P F DH-5460 NTS 4 OF 12 MD-DH5460-01 C NOTE 2,THIS SHEET. P.E#58705 REGIuTRAnON