|
y� REV. REVISION& RMSED Ere DATE:
<br /> hpVlllllry,rr ` R
<br /> 4/15/2020 7 .1 1 T.D.O' 12/23/09
<br /> LUCAS A TURNER,P.E. apA OVEO SIZES PFA NEw STING e[ T.D.D. 11/2)/II
<br /> MODEL DESIGNATION: Simonton Double Hung Series 07-09 /07-10 /07-20 Vinyl Window Lucas Turner '*' *= FL PE 6 58201
<br /> _9f No.58201 tct_ TURNER ENGINEERING k g UPDATED SIZE CHART PER NEW TESTING T.D.D. 03/04/13
<br /> UM MAXIM OLTRALL NOMINAL SIZE: See Size Chart 2020.04.15 ='p; * 1WE
<br /> CONSULTING,INC.
<br /> 1 a!C B.S 0e/19/I5
<br /> 14:18:15-05'00' . , , ? (CON 29779) 10 ADDED MIN EDGE DIST NOTE.
<br /> DESIGN PRESSURE RATING:_ See Size (,"hart i Fa� OAp�'�(y`,� 2428OLDEN.A TTN 38320 1RL 11 ADDED N07ES 14 h 15-AAMA 800 LMH 08/31/17
<br /> USABLE CONFIGURATIONS, X "rrq��HIA�I���` PH.941-380-1574
<br /> X
<br /> GENERAL DESCRIPTION: The head, sill, and side jambs are extruded PVC. The wall thickness MIN.EDGE DIST.
<br /> through which the anchor screw penetrates is a minimum of 0.142". SEE TABLE 1 INSTALLATION FASTENER
<br /> SEE TABLE 1
<br /> SUBSTRATE
<br /> BY OTHERS
<br /> MIN.EMBED.
<br /> 6- 1 B" SEE TABLE,1
<br /> �— SILICONE CAULK
<br /> (INT.PERIMETER)
<br /> SIZE CHART SILICONE CAULK SEE NOTES 14&15 MIN.EMBED.
<br /> Q \ OVERALL SIZE DP RATING SE(EXT.PERIMETER) 1/4-MAX SHIM SEE TABLE 1
<br /> E NOTES 14 k IS
<br /> CIRCLED AT ANCHORS SILICONE CAULK
<br /> WIDTH HEIGHT ANCHOR (INT.PERIMETER)
<br /> "H" LOCATIONS H SEE NOTES 14 k 15
<br /> REQUIRED? 1 HEAD SUBSTRATE
<br /> 0 48" fill" N0 *25 PSF 1 BY OTHERS
<br /> 1/4"MAX SHIM
<br /> 56" 84" NO 01 L AT ANCHORS
<br /> CIRCLED ANCHOR LOCATIONS 36 63 NO _ 1/4'MAX SKIM
<br /> RI .
<br /> W REQUIRED FOR SOME SIZES, ;4
<br /> SEE SIZE CHART m 44" 64" NO (BY OTHERS) INSTALLATION:1:
<br /> TABLE FASTENERS
<br /> 1 t50 PSF
<br /> 47" 71" 'YES SILICONE CAULK SEE NOTONE CAULK
<br /> 53 76" YES SEE NOTES 14 k 15 SEE NOTES 14&IS
<br /> 37" 84" YES t60 PSF MIN.EDGE DIST. SILICONE CAULK
<br /> p 37" 76" YES *65 PSF SUBSTRATE SEE TABLE 1 (EXT.PERIMETER)
<br /> JM�l
<br /> 11 BY OTHERS SEE NOTES 14&15
<br /> SILL JAMB
<br /> x
<br /> NOTES:
<br /> 1.This Installation has been evaluated for use In locations adhering to the Florida Building Code outside the HVHZ,and where pressure requirements as datemYned by ASCE 7 Minimum Design Loads for Buildings
<br /> and Other Structures do not exceed the design pressure ratings herein.
<br /> 2.Ali Interior and extorter perimeter surfaces of the window must be caulked.
<br /> n 3.Anchor type,elm spacing,embedment,and edge distance shall be as specified In these drawings Use appropriate anchorage tram Table 1 according to substrate type.A minimum center-tocenter spacing of 3'
<br /> shall be maintained between all masonry fasteners In any direction,and 1'mWmum center-to-center spacing for all other fastmenYsubsbs ale
<br /> 4.Anchor embedment to substrate shag be beyond wail dressing or stucco.For masonry openings with wood buds less than 1-12"thick embedment shall be beyond wood bucks.If used,and Into masonry
<br /> substrate.Wood buds with masonry are ckfastoptional.
<br /> 5.Wood or masonry openings,buds,and buds fasteners,by others,shell be property designed and Installed to transfer wind Toads to the structure.
<br /> 6.The responsibility for selection of Simonton products to meet any applicable local laws,building codes,ordinances,or other safety requirements rests solely with the architect,building owner,or contractor,
<br /> 7.Shims are required whom gaps of greater than 1116'exist between opening and frame.Max shim stack Is 1/4'.Shims shall be bad-beadng and capable of transferring loads to the substrate.
<br /> Q 8.When used In areas requiring Impact protection,this product REQUIRES the use of approved Impact resistant shutters or other external protection.
<br /> 9.Sealing and flashing by others should be applied using the ASTM E 2112 methodology appropriate for the opening Into which the product Is being Installed.Overall water penetration resistance of the Installed
<br /> �"VrMAX OVERALL'FRAME WIDTH product Is nat addressed In this claiming and Is the responslNlity of others
<br /> 10.Glazing shag comply with ASTM E 1300.
<br /> 11.All fasteners penetrating Into pressure treated wood shall be capable of preventing corrosion due to reaction with pressure treatment chemicals Any disslmliar materials that come Into contact shall be protected
<br /> to prevent reactions In accordance with code requirements
<br /> 12.A wind load duration factor Cd-1.6 weer used for the analysis of woad screws only.
<br /> 13,Products shag be constructed as specified In AT]test reports A9235.01.50147,C3513.01-109-47,C5631,01-109-47,C7745.01-10947,C9037.01-501-47,D0294.01-501-47 and D0296.01-501.47.
<br /> 14.Use 100%pure silcone caulk compliant with AAMA 808 Section 5.Sealant Specificaflons for use With Architectural Fenestration Products.Make sum surfaces are completely free from all rid caulk,damaged
<br /> wood,wood fibers,grease,all dirt,rust,mold or similar contaminants Vacuum and dean opening surfaces completely.A fully primed surface is recommended,but not required.Cleating of an surfaces should be
<br /> TABLE 1: INSTALLATION FASTENERS TABLE done the same day of which the silicone caulk Is to applied For more details visit simonten.com.
<br /> MIN EDGE 15.Caulk application:recommended air and surface temperatures at the time of application am to be between 40 and 90 degrees F.Insure all contact surfaces are d w wean and dry including the ne indow(s}Use a
<br /> ID SUBSTRATE TYPE ANCHOR TYPE MIN. EMBED
<br /> OISYANCE backer red on 90 Joints>WAI'deep and/orwlder than 114".Flrdshed caulkloint should be a ndnimum of 3I8'deep and make fug contact with troth the new window and structural opening surfaces.Silicone caulk
<br /> A CONCRETE 2 KSI MIN. 3/16"ITW TAPCON 1-1/2" 1-1 B" should be forced Into)alnt or compressed to assure full contact on both surfaces and to expel any air pockets
<br /> HOLLOW OR GROUT-FILLED CMU _ _______ - -
<br /> B 3/16"ITW TAPCON_ --- N'rO B IN 066 11
<br /> 117 PCF MIN. 1' 2 __-_____--- F.A"'
<br /> -- meapaiRE STATEMENT SIMO N' D
<br /> C 2X MIN. SOUTHERN PINE WOOD 3/16"IITV TAPCON 1-3/B" 7/8" Thla document la the properly of Simonton Windows.whlN M: Oimenetand Tolerances w 1 N o o w s DRAW
<br /> N BY: DATE:
<br /> G=0.55 retains oil proprietary and other right.to Ile subject molter. unl Otherwise So 76.d C.LS. 03/22/06
<br /> D 2%MIN. SOUTHERN PINE WOOD 810 WOOD SCREW 1-3/8" 7/8" This document is provided to the reciplont on the expressedTEMPER: 1 Cochrane Avcoue
<br /> G-0.55 condition That It to not to be dtedaned,reproduced to whole or Passboro,W V 26415 CHECKED BY:DALE:
<br /> 16 GAUGE 0.060 MIN.STEEL 10-16 ITW TEKS - FULL THREAD 1 2" pat,nor used to conjunction with the design,manufacture or Decimals Angles
<br /> E / SCALE: EET: APPR D BY:DATE:
<br /> STUD 33KSI YIELD MIN. SELF-DRILLING SCREW repair of goods for anyone other than Svnonlon Window. FIT
<br /> 'To,
<br /> 1
<br /> F 1 B ALUM. 6063-T5 MIN. OR 10 RADE 5 SELF-TAPPIN FULL THREAD 1/2" without its consent. This restriction does not I'unit the A t•03SEWES:1 8"STEEL 36 KSIMIN DRILLING SCREW recipient'.rights to utnbm information contained to this xx t 01 0' 30 min. 07-09/07-10/07-20 DOUBLE HUNG
<br /> document which is properly obtained from another source. EATMENT: .XXX 3 .005
<br /> nnE:
<br /> FlLE:IN0066 1%BUCK INSTALLATION
<br />
|