20-1178 - Laserfiche WebLink

Browse Search

- 4099 MAPNET ll/IDNet Addressable U5i F*'p1EX Manual Pull Station with LED Installation istructions Setting the Pull Station Address Manual hull Station Operation, Continued Each Pull Station has a unique address that is set via an eight-position DIP switch. : B)Double Action"Break Glass"Stations4099-9005(see Figure 6B) DIP switch position 1 is the least significant bit(LSB)and position 8 is the most To activate: �-►. PULL DOWN j ignificant bit.(MSB). 1.Break the glass with the hammer. Set the address using Figure 4 as reference.Use a small screwdriver or pen to set the I.Pull the handle down firmly to break the rod that is visible below the handle.This witches.The device address for the Pull Station should be written on the causes an alarm to sound and the actuation of annunciator contacts if,provided. e-sealable label.This information provides aid_ while troubleshooting the system. To reset: 4099-9Q04 1.Unlock and o111 pen the front of the station and replace the rod. LS9 MSB DIPSWIT,CH 15 SHOWN 5 ET AT ADDR ES S:7.. .. 1" "U'.lnlwCJ�1 t -'E 2.Replace the glass plate as shown in the replacement drawing(see Figure 5). ON 1 2 3.4.S 6 II�nIII11I 6 ' - - - 011 -oN � to=OFF Hammer � PULL DOWN replace 1.Swing the hammer from the front 4" RESERVED FOR •• � 'L=' DIP SWITCHES STHRU 8 FUTURE USE t 09979005" Glass 0000 loon 0100 1100 0010.1010 0110 111D 0001 1001:o101 1101 0011 loll 0111 111] of the station. 0000 0 :16 32 48 .64 80 96 .112 128 144' '160 176 192 :208 224 24'0 Plate ' . '1000 1 ..17' '33 49 :65 87 47 .713 129 145167 177 193209 225 241: 2._Fit the glass retainer tothe bottom " .. . 0100. 2 18 34 50 66 82 98 114 130 146 162 178 1,94 210 226 242 �,..- , of the gop of he - 1100" 3 14 35 51 67 83 99 115 131 147 163 179 195 211 227 243 3.Fit the top of the glass plate behind j the tab. PULL DOWN. 0010 4 20 36 52 68 84 100 116 732 148 764 180 196 212 228 244 --� - 1010' 'S 21 37 -53 64 85 101 117 133 149 165 181 197 213 229 24S �- 4.Slide the glass retainer into the station 0110• 6 22 38 S4 70 86 702 118 134 150 166 182198 214 230 246 .- until.it snaps into place. --;,,�xh DIP 1170 7 23 39 55 71 87 103 119 135151 167 183 .799 215231247 _ SWITCHES 0001 8 24 40 56 .72 .88 104 120 136 152 168. 184 200 216 232 248 5•Gently return the hammer t0 its normal 1 THRU a. lass Retainer position: C 4099-9006 1001 9 25 '41 57 73 -89 105 121 137 153 169 185 201 217 233 249 0101 10 26 42 58 74 90 106 122 138 154 -170 186 202 218 234 250 . Figure 5.Replacing Glass Plate . ]101 ti 2743 59 7S :9] 307123 139 155 171 187 203 219 235 2S1 _ _. 0011 12 '28. 44 b0 "Ib 92k10 124 140 156 172 188 204 :220 236 252 C)_Double Action"Push Type"Stations'4099-9006:&4099-9015(see Figure 6C} '- 1011 13 ,29, 45 61 :77, ,43 :125 141 157. 173 169 205 221. 237 253o111• 14 30 46 62 78 94 126 142 158 174 190 206 222 438 254 To activate. PULL DOWN 1111 15 31 47 63 79 95 127 143 159 175 "191 207 223 239 zs5 1'.Push on the push bar. 1 RESERVED FOR FUTURE iisE. 2.Pull the handle down firmly to.break the rod that is visible below,the handle.This Figure C Addressable Manual Pull Station with LED Address Chart g causes an alarm to.sound and.the actuation of annunciator contacts;if provided.: 4099-9015 Votes: -1.The IDNet channel(4010 FACP only)supports address codes 1 through 250.The To reset: MAPNET 11.channel(4100,or4120,or 4020 FRCP)supports address codes 1 through 127: Unlock and open the front of the station and replace the rod. 2.4010 FACP:(I,DNet Channel)references:•Installation;and Programming manual 574- D Single Action NO GRIP Station 4099-9021(see Figure6D) ^. , 187;4010.Fire Alarm manual 574-052;4010 panel label 526-444.. ) g 3.4100/412014020-FACP(MAPNET 11 Channel)references:4100,4120;or 4020 To activate: Programmer's Report. Rotate actuator forward and down to break the rod that is visible bellow the Manual Pull Station Operation handle.This causes an alarm to sound and the actuation, f:of contacts,if provided. : . 4099-9021 4.)Single Action Stations 4099-9004(see Figure 6A) ; To reset: ro activate: Unlock and open the front of the station and replace the rod.' 45` lull the handle down firmly to break the rod that is visible below the handle.This Notes: 1.4099 Series stations for release applications{4099-9015)has a blank area on auses an alarm to sound and the actuation of annunciator contacts,if provided. the front of the station for an application label. Label Kit 4099-9802 is ordered Co reset: separately and provides 6 release applications labels(see Figure 6E). L^ ' 2:4099-9004 can be retrofitted to be a NO GRIP manual station using 4098-9805 4099-9802 Jnlock and open the front of the station and replace the rod: retrofit kit: Figure;6.Addressable Manual Pull Stations i79-1135. 579-1135 kev B . .. _. Rena.B