20-1261 - Laserfiche WebLink

Browse Search

dn-7114:c•Al-65 N-ANN-80 NOT 1 F'1 E R so-Character LCD Serial Annunciator by Honeywell Annunciators General The N-ANN-80 annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display. It provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced condi- tions. The N-ANN-80 and the FACP communicate over a two- wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host FACP or a remote UL-listed, filtered power supply. N-ANN-80 is black;for white order N-ANN-80-W. The N-ANN-80 displays English-language text of system point N �j NOTIFIER information including device type, zone, independent point I ,.,T E byH°nay weIII alarm, trouble or supervisory status, as well as any custom alpha labels programmed into the control panel. It includes con- trol switches for remote control of critical system functions. (A s keyswitch prevents unauthorized operation of the control switches.) Up to eight N-ANN-80s may be connected to the ANN-BUS of each FACP. Minimal programming is required,which saves time during system commissioning. The N-ANN-80 is compatible with NOTIFIER FACPs with an ANN-BUS,such as the NFW-50. Features • Trouble • Supervisory • Listed to UL Standard 864,9th Edition. • Alarm Silenced • Backlit 80-character LCD display(20 characters x 4 lines). • Mimics all display information from the host panel. Specifications • Control switches for System Acknowledge, Signal Silence, . Operating voltage range: 18 VDC to 28 VDC. Drill,and Reset. ' • Control switches can be independently enabled or disabled ' Current consumption @ 24 VDC nominal(filtered and non- at the FACP.• 40 mA maximum. • Keyswitch enables/disables control switches and mechani- ' Ambient temperature:32°F to 120°F(0°C to 49°C). cally locks annunciator enclosure • Relative humidity: 93%±2% RH (noncondensing) at 32°C • Keyswitch can be enabled or disabled at the FACP. ±2°C(90°F±3°F). • Enclosure supervised for tamper. • 5.375" (13.65 cm.) high x 6.875' (17.46 cm.) wide x 1.375" (3.49 cm.)deep. • System status LEDs for AC Power,Alarm,Trouble, Supervi- For use indoors in a dry location. • Local sounder can be enabled or disabled at the FACP. so and Alarm Silence. All connections are power-limited and supervised. • N-ANN-80 connects to the ANN-BUS terminal on the FACP Agency Listings and Approvals and requires minimal panel programming. • Displays device type identifiers, individual point alarm, trou- The listings and approvals below apply to the N-ANN-80. In ble,supervisory,zone,and custom alpha labels. some cases, certain modules may not be listed by certain • Time-and date display field. approval agencies,or listing may be in process. Consult factory • Surface mount directly to wall or to single, double, or 4" for latest listing status. square electrical box. • UL:S635 • Semi-flush mount to single, double, or 4' square electrical • FM approved box.Use ANN-SB80KIT for angled view mounting. • CSFM:7120-0028:240 • Can be remotely located up to 6,000 feet(1,800 m)from the • MEA:442-06-E Vol.2 panel. • Backlight turns off during AC loss to conserve battery power The ANN-BUS but will turn back on if an alarm condition occurs. • May be powered by 24 VDC from the host FACP or by remote POWERING THE DEVICES ON THE ANN-BUS FROM power supply(requires 24 VDC). AUXILIARY POWER SUPPLY • Up to eight N-ANN-80s can be connected on the ANN-BUS. The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the Controls and Indicators ANN-BUS power requirements. See the FACP manual for more • AC Power information. • Alarm dn-7114:c•5/22/09—Page 1 of 2