20-1261 - Laserfiche WebLink

Browse Search

DN-60918:A Indoor Selectable-Output Horns, Strobes, and Horn N OTI F I E R Strobes for Wall Applications by Honeywell AudioNisuall Devices-The L-Series offers the most versatile and easy-to-use line of horns,strobes,and horn strobes in the industry with lower cur- rent draws and modern aesthetics. With white and red plastic housings, standard and small footprint devices, and plain, FIRE-printed devices, L-Series can meet virtually any applica- tion requirement. The L-Series product line of wall-mount horns, strobes, and q horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature plug-in designs with minimal intrusion into the back P2RL box, making installations fast and foolproof while virtually elim- inating costly and time-consuming ground faults. To further simplify installation and protect devices from con- struction damage, L-Series utilizes a universal mounting plate for all standard and compact models with an onboard shorting F F spring,so installers can test wiring continuity before the device j is installed. I I ' Installers can also easily adapt devices to a suit a wide range R . •..,� J ..�•�%,� � � R of application requirements using field-selectable candela set- E tings, automatic selection of 12- or 24-volt operation, and a � E rotary switch for horn tones with two volume selections. Features P2GWL SGWL • Updated modern aesthetics. • Small profile devices for Horns and Horn Strobes. • Plug-in design with minimal intrusion into the back box. • Tamper-resistant construction. • Automatic selection of 12-or 24-volt operation at 15 and 30 candela. , • Field-selectable candela settings on wall units: 15, 30, 75, 95, 110, 135,and 185. • Horn rated at 88+dBA at 16 volts. • Rotary switch for horn tone and two volume selections. >� _ • Universal mounting plate for all standard and all compact HWL wall units. • Mounting plate shorting spring checks wiring continuity. before device installation. • Electrically Compatible with legacy SpectrAlertP and 12 or 24 volts. When used with the Sync•Circuit Module, 12- SpectrAlert Advance devices. volt-rated notification appliance circuit outputs shall operate • Compatible with MDL3 sync module. between 8.5 and 17.5 volts; 24-volt-rated c appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor • Listed for wall mounting only. L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unaltered Architectural/Engineering Specifications power supply.Strobes and horn strobes shall have field-select- General: L-Series standard horns, strobes, and horn strobes able candela settings including 15, 30, 75, 95, 110, 135, and shall mount to a standard 2" x 4° x 17/8" back box, 4° x 4° x 185. 1'/2°back box,4°octagon back box, or double-gang back box. Strobe. The strobe shall be a L-Series Model listed to UL L-Series compact products shall mount to a single-gang 2° x 1971 and shall be approved for fire protective service. The 4° x 17/8° back box. A universal mounting plate shall be used strobe shall be wired as a primary-signaling notification appli- for mounting ceiling and wall products for all standard-size ance and comply with the Americans with Disabilities Act models and a separate universal mounting plate shall be used requirements for visible signaling appliances,flashing at 1 Hz for mounting compact wall models. The notification appliance over the strobe's entire operating voltage range. The strobe circuit wiring shall terminate at the universal mounting plate. light shall consist of a xenon flash tube and associated lens/ Also, L-Series products, when used with the Sync•CircuitTm reflector system. Module accessory, shall be powered from a non-coded notifi- cation appliance circuit output and shall operate on a nominal DN-6091 BA•2/3/2017—Page 1 of 4