Laserfiche WebLink
l <br />IGT. <br />R. <br />v <br />00 <br />50 <br />LEFT ELEVATION <br />SCALE: 3/16" = V-0" <br />RIGHT ELEVATION <br />SCALE: 3/16" = V-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />txterlor Lovering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations, <br />REV. 09.24.21 <br />>4-4o <br />e� 0 CO <br />ev, 0-cox <br />cc to LL a...' <br />-. .. -0© y <br />C: o <br />Uy s v <br />0 <br />U 0) <br />w cr <br />S <br />Ll..+ <br />`;i`i ci l9�viyr�a,Ep'i F3 Q7g kit <br />.�°s,..# <br />q`. <br />S <br />< ,� e <br />. <br />e L .•'a <br />.......... <br />C?�.ESSI <br />�, <br />ti <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />h <br />W v E <br />0 <br />o n c <br />g <br />,+ <br />V N r <br />G aO N <br />M dj C" ggg u <br />Q tu LL C W W <br />tu <br />J Li— LL S W 0_ <br />-v o <br />Z <br />;a o z 0 <br />5 0 <br />W ��Ow <br />m <br />- r <br />Z N Z <br />0 <br />ILW <br />04 <br />N o <br />Z o� U cc <br />�� <br />z N 0 <br />o <br />z � N <br />z o <br />J — <br />n— Y) <br />M <br />to z <br />� U 0 <br />12 <br />OLU <br />Ln y <br />�tJ1 <br />U <br />W J <br />r— — E <br />i <br />r <br />z� <br />U 6 <br />c CD <br />¢ 0 <br />�® <br />N <br />O <br />� <br />w <br />o <br />Z <br />� <br />LJ1_ <br />z o <br />DO <br />Z <br />O <br />E <br />z <br />Z o <br />Z@ <br />L <br />o o: <br />so <br />I <br />O E <br />a� <br />z <br />U <br />�Z <br />a <br />Z <br />N � <br />¢ <br />L <br />:7, <br />N <br />— <br />❑ <br />.y <br />U <br />O <br />m � <br />Z O <br />Z <br />N J <br />0 <br />� m <br />4 W <br />� 0 <br />a 3 <br />;� <br />SZ <br />LL'0 <br />So <br />a <br />W <br />U <br />ado <br />aLL <br />= <br />CD <br />IXw X <br />r <br />o� <br />,� <br />LZ0 3 <br />c O <br />0 <br />M <br />rn <br />N0 <br />r <br />r <br />L <br />CO <br />CD <br />c+� <br />Ln <br />M <br />N <br />N <br />/=3 <br />CD <br />60 <br />_;C <br />V) m <br />CD <br />co <br />N <br />�-- <br />O <br />Ln <br />i <br />CD <br />O <br />cn <br />i <br />CO <br />T <br />CN <br />r <br />CD _Z <br />LO <br />o <br />Z <br />E Ocu <br />a <br />E <br />� ¢ o <br />� <br />JOB NO: 22-05610-05605 <br />SCALE : AS NOTED <br />SHEET NO. <br />7.2 <br />