5915 Gall Blvd (2) - Laserfiche WebLink

Browse Search

DESCRIPTION OF OPERATION: EXTERIOR SIGNAGE TO BE TURNED ON BY PHOTO CELL. SIGNAGE WILL BE SWITCHED OFF BY TIME SWITCH AT CLOSE. COORDINATE WITH PIZZA HUT CONSTRUCTION MANAGER ON TIME SETTINGS FOR INTERIOR LIGHTING. PHOTO CELL N H B-19 OVERIDE SWITCH. SEE LIGHTING PLAN FOR MORE INFORMATION. ab LOBBY AREA EXIT SIGN/EMERGENCY LIGHTING B-3 �b�-� KITCHEN AREA cam---► KITCHEN AREA EXIT SIGN/EMERGENCY LIGHTING B-11 SIGNAGE SPARE TIME SWITCH: TORK MODEL #DLC400BP LIGHTING CONTROLS SYSTEM TESTING REQUIREMENTS PROVIDE EVIDENCE THAT THE LIGHTING CONTROL SYSTEMS HAVE BEEN TESTED TO ENSURE THAT CONTROL HARDWARE AND SOFTWARE ARE CALIBRATED, ADJUSTED, PROGRAMMED AND IN PROPER WORKING CONDITION IN ACCORDANCE WITH THE CONSTRUCTION DOCUMENTS AND MANUFACTURER'S INSTRUCTIONS. FUNCTIONAL TESTING SHALL BE IN ACCORDANCE WITH SECTIONS C408.3.1.1 AND C408.3.1.2 FOR THE APPLICABLE CONTROL TYPE.. OCCUPANT SENSOR CONTROLS: THE FOLLOWING PROCEDURES SHALL BE PERFORMED: 1. CERTIFY THAT THE OCCUPANT SENSOR HAS BEEN LOCATED AND AIMED IN ACCORDANCE WITH MANUFACTURER RECOMMENDATIONS. 2. FOR PROJECTS WITH SEVEN OR FEWER OCCUPANT SENSORS, EACH SENSOR SHALL BE TESTED. 3. FOR PROJECTS WITH MORE THAN SEVEN OCCUPANT SENSORS, TESTING SHALL BE DONE FOR EACH UNIQUE COMBINATION OF SENSOR TYPE AND SPACE GEOMETRY. WHERE MULTIPLES OF EACH UNIQUE COMBINATION OF SENSOR TYPE AND SPACE GEOMETRY ARE PROVIDED, NOT LESS THAN 10 PERCENT, BUT IN NO CASE LESS THAN ONE, OF EACH COMBINATION SHALL BE TESTED UNLESS THE CODE OCIAL OR DESIGN PROFESSIONAL REQUIRES A HIGHER PERCENTAGE TO BE TESTED. WHERE 30 PERCENT OR MORE OF THE TESTED CONTROLS FAIL, ALL REMAINING IDENTICAL COMBINATIONS SHALL BE TESTED. FOR OCCUPANT SENSOR CONTROLS TO BE TESTED, VERIFY THE FOLLOWING: 3.1 WHERE OCCUPANT SENSOR CONTROLS INCLUDE STATUS INDICATORS, VERIFY CORRECT OPERATION. 3.2 THE CONTROLLED LIGHTS TURN 0 OR DOWN TO THE PERMITTED LEVEL WITHIN THE REQUIRED TIME. 3.3 FOR AUTO -ON OCCUPANT SENSOR CONTROLS, THE LIGHTS TURN ON TO THE PERMITTED LEVEL WHEN AN OCCUPANT ENTERS THE SPACE. 3.4 FOR MANUAL -ON OCCUPANT SENSOR CONTROLS, THE LIGHTS TURN ON ONLY WHEN MANUALLY ACTIVATED. 3.5 THE LIGHTS ARE NOT INCORRECTLY TURNED ON BY MOVEMENT IN ADJACENT AREAS OR BY HVAC OPERATION. TIME -SWITCH CONTROLS: WHERE TIME -SWITCH CONTROLS ARE PROVIDED, THE FOLLOWING PROCEDURES SHALL BE PERFORMED: 1. CONFIRM THAT THE TIME -SWITCH CONTROL IS PROGRAMMED WITH ACCURATE WEEKDAY, WEEKEND AND HOLIDAY SCHEDULES. 2. PROVIDE DOCUMENTATION TO THE OWNER OF TIME -SWITCH CONTROLS PROGRAMMING INCLUDING WEEKDAY, WEEKEND, HOLIDAY SCHEDULES, AND SET-UP AND PREFERENCE PROGRAM SETTINGS. 3. VERIFY THE CORRECT TIME AND DATE IN THE TIME SWITCH. 4. VERIFY THAT ANY BATTERY BACK-UP IS INSTALLED AND ENERGIZED. 5. VERIFY THAT THE OVERRIDE TIME LIMIT IS SET TO NOT MORE THAN 2 HOURS. 6. SIMULATE OCCUPIED CONDITION, VERIFY AND DOCUMENT THE FOLLOWING: 6.1. ALL LIGHTS CAN BE TURNED ON AND OFF BY THEIR RESPECTIVE AREA CONTROL SWITCH. 6.2. THE SWITCH ONLY OPERATES LIGHTING IN THE ENCLOSED SPACE IN WHICH THE SWITCH IS LOCATED. 7. SIMULATE UNOCCUPIED CONDITION. VERIFY AND DOCUMENT THE FOLLOWING: 7.1. NONEXEMPT LIGHTING TURNS OFF. 7.2. MANUAL OVERRIDE SWITCH ALLOWS ONLY THE LIGHTS IN THE ENCLOSED SPACE WHERE THE OVERRIDE SWITCH 1S LOCATED TO TURN ON OR REMAIN ON UNTIL THE NEXT SCHEDULED SHUTOFF OCCURS. DAYLIGHT RESPONSIVE CONTROLS: WHERE DAYLIGHT RESPONSIVE CONTROLS ARE PROVIDED, THE FOLLOWING SHALL BE VERIFIED: 1. CONTROL DEVICES HAVE BEEN PROPERLY LOCATED, FIELD CALIBRATED AND SET FOR ACCURATE SETPOINTS AND THRESHOLD LIGHT LEVELS. 2. DAYLIGHT CONTROLLED LIGHTING LOADS ADJUST TO LIGHT LEVEL SET POINTS IN RESPONSE TO AVAILABLE DAYLIGHT. 3. THE LOCATIONS OF CALIBRATION ADJUSTMENT EQUIPMENT ARE READILY ACCESSIBLE ONLY TO AUTHORIZED PERSONNEL. DOCUMENTATION REQUIREMENTS: DOCUMENTS CERTIFYING THAT THE INSTALLED LIGHTING CONTROLS MEET DOCUMENTED PERFORMANCE CRITERIA OF SECTION C405 ARE TO BE PROVIDED TO THE BUILDING OWNER WITHIN 90 DAYS FROM THE DATE OF RECEIPT OF THE CERTIFICATE OF OCCUPANCY. QUANTITY LAMP NO. LOCATION MANUFACTURER / CATALOG NUMBER DESCRIPTION MOUNTING VOLT WATT REMARKS NEW EXISTING # TYPE A 17 KITCHEN/ PHILIPS / DAY-BRITE 2' x 4' LED TROFFER - INCLUDED LAY -IN GRID UNV 45 2X4 LED TROFFER WITH 3500K COLOR RESTROOM #2TG48L835-4-FS-02F-UNV TEMPERATURE A5 3 KITCHEN PHILIPS / DAY-BRITE 2' x Z LED TROFFER - INCLUDED LAY -IN GRID UNV 43.5 2X2 LED TROFFER WITH 3500K COLOR #2TG38L835-2-FS-02F-UNV TEMPERATURE C 13 ENTRY ACCUSERV / 00395-016 / CT6FB /RC6-12W DOWNLIGHT - LED CEILING 120 12 TRIM: BLACK D 3 ENTRY ACCUSERV / ITEM: BES00298-105 CORD HUNG PENDANT 1 9.5W Al LED CEILING 120 9.5 FINISH: CORD HUNG PENDANT WITH WITH 18W GU24 BASE 2,700K RED SAND GLASS SHADE E 3 WALK-IN SUPPLIED BY WALK-IN COOLER/FREEZER - - - SURFACE - - EM1 2 ENTRY EXITRONIX / NFT-B-G2 EMERGENCY LIGHT - INCLUDED WALL 120 - EMERGENCY FIXTURE WITH 90 MINUTE EMERGENCY BATTERY BACKUP. FINISH: BLACK EM2 7 KITCHEN EXITRONIX / NFT-W-G2 EMERGENCY LIGHT - INCLUDED WALL 120 - EMERGENCY FIXTURE WITH 90 MINUTE EMERGENCY BATTERY BACKUP. FINISH: WHITE EM3 3 EXTERIOR ACCUSERV / ITEM: CAMN/LX6-DB EXTERIOR - 6W XENON WALL 120 - EMERGENCY FIXTURE EMERGENCY LIGHT WET LOCATION RATED Ki 1 ENTRY BEST LIGHTING PRODUCTS LED EXIT SIGN - LED CEILING 120 3 BLACK EXIT FIXTURE WITH EMERGENCY BATTERY. EZXTEU-2-R-B-EM SEE LIGHTS FIXTURE SCHEDULE NOTE #2. K2 6 KITCHEN BEST LIGHTING PRODUCTS LED EXIT SIGN - LED CEILING 120 3 WHITE EXIT FIXTURE WITH EMERGENCY BATTERY. EZXTEU-2-R-W-EM SEE LIGHTS FIXTURE SCHEDULE NOTE #2. J 3 ENTRY ACCUSERV / ITEM: 2001-002 TRACK LIGHT HEADS 1 PAR20 LED TRACK 120 8 FINISH: BLACK J132 1 ENTRY ACCUSERV / ITEM:6048BK 2' TRACK - - CEILING - - FINISH: BLACK REFER TO LIGHT FIXTURE SCHEDULE NOTE #3 JB4 2 ENTRY ACCUSERV / ITEM:60486K 4' TRACK - - CEILING - - FINISH`. BLACK REFER TO LIGHT FIXTURE SCHEDULE NOTE #3 W1 0 EXTERIOR RAB / ITEM: WP2H1500T/PC WALL PACK- - ED17 WALL 120 185 SUFFACE MOUNT FIXTURE BRONZE FINISH 150W AT 8'-0" AFF TO CENTER ALL LIGHT FIXTURES ON LIGHT FIXTURE SCHEDULE FURNISHED BY OWNER AND INSTALLED BY ELECTRICAL CONTRACTOR. LIGHTING FIXTURE CONTACTS: ACCUSERV EQUIPMENT & SUPPLY 3865 PRODUCE RD., SUITE #208, LOUISVILLE, KY 40218, PHONE: 877-707-7378, FAX: 502-961-0357. 1. OWNER WILL PROVIDE LIGHT FIXTURES WITH ELECTRONIC BALLASTS. COMPACT FLUORESCENT ELECTRONIC BALLASTS SHALL HAVE END -OF -LIFE PROTECTION CIRCUIT TO PREVENT WELDING OF LAMPS IN SOCKETS OR LAMP BREAKAGE. SEE SPECIFICATIONS. 2. OWNER WILL PROVIDE ARROWS AND FACES AS INDICATED ON THE DRAWINGS. FIXTURES ARE PROVIDED WITH REMOVABLE CHEVRONS FOR DIRECTIONS INDICATED ON PLAN. 3. OWNER WILL PROVIDE TRACK, END FEEDS, AND COUPLING DEVICES IN QUANTITIES AS REQUIRED TO FORM THE TRACK LENGTHS SHOWN. REFER TO THE PLANS FOR TRACK LOCATION. REFER TO ARCHITECTURAL REFLECTED CEILING PLAN AND ELEVATIONS FOR EXACT LOCATIONS OF LIGHTING FIXTURES. 4. ELECTRICAL CONTRACTOR SHALL VERIFY ALL FIXTURE LOCATIONS WITH ARCHITECTURAL PLANS. 5. ELECTRICAL CONTRACTOR SHALL INSTALL ALL CEILING MOUNTED LIGHTING FIXTURES IN LOCATIONS AS INDICATED ON THE ARCHITECTURAL REFLECTED CEILING PLAN. 6. CONFIRM LIGHTING FIXTURE QUANTITIES WITH SUPPLIER. 7. CONTRACTOR TO FIELD VERIFY CEILING TYPE AND PROVIDE PROPER MOUNTING HARDWARE. 8. SPEAKERS INSTALLED BY OTHERS. 9. VERIFY LOCATION OF NEW SWITCH BANK WITH NPC FACILITES/PROJECT MANAGER. INTERIOR LIGHTING & EXTERIOR SIGNAGE CONTROL DIAGRAM 1 6 1 LIGHTING FIXTURE SCHEDULE 1 5 1 LIGHT FIXTURE SCHEDULE NOTES 1 4 1 NOTE: ALL CEILING FIXTURES AND PENETRATIONS TO CONFORM TO ANSI/UL 263 STANDARDS. ELECTRICAL LIGHTING PLAN 1 /4" = 1'-0" 2 O COOLER/FREEZER LIGHTS FURNISHED BY MANUFACTURER. CIRCUIT AS SHOWN. NO AUTOMATIC CONTROLS FOR THIS SPACE ARE REQUIRED SINCE THE LIGHTS HAVE AN EFFICACY OF MORE THAT 40 LM/W. O2 PROVIDE TIME SWITCH, EXTERIOR PHOTOCELL SENSOR AND LIGHTING CONTACTOR AS SHOWN IN DETAIL 6 ON THIS SHEET. MOUNT TIME SWITCH AND LIGHTING CONTACTOR ADJACENT TO PANELBOARD'B' AND MOUNT EXTERIOR PHOTOCELL SENSOR ON ROOF PER MANUFACTURER LITERATURE. O VERIFY EXACT LOCATION OF SWITCH BANK WITH NPC FACILITIES/PROJECT MANAGER. ® SIGNAGE DISCONNECT SWITCH; NEMA 3R, LOCKABLE. EXACT LOCATION TO BE DETERMINED IN FIELD.. O CONNECT HOOD LIGHTING WITHIN OVEN AND FRYER HOODS TO HOOD CONTROL PANEL CONTROL CIRCUIT. COORDINATE ALL WIRING AND REQUIRED CONNECTION WITH HOOD MANUFACTURER. MOUNT EXTERIOR EMERGENCY EXIT LIGHTING FIXTURE @ 96" A.F.F. ON FACE OF EXTERIOR WALL. CIRCUIT AS INDICATED. COORDINATE EXACT LOCATION WITH BUILDING OWNER AND TENANT. O PROVIDE WALL MOUNTED OCCUPANCY SENSOR AS SHOWN ON PLANS FOR CONTROL OF RESTROOM LIGHT AND EXHAUST FAN. WATTSTOPPER MODEL# PW-100. ® PROVIDE OVERRIDE SWITCH FOR TIMESWITCH: TORK MODEL#SS410. SWITCH SHALL BE PROGRAMMED TO OVERRIDE TIMESWITCH FOR A MAXIMUM OF 2 HOURS. LABEL SWITCH WITH ZONES CONTROLLED, KEYNOTES 1 3 1 R-? R-.q R-:q a b c 0 0 0 NOTE: VERIFY LOCATION OF NEW SWITCH BANK W/ NPC FACILITIES/PROJECT MANAGER. NOTE: PROVIDE PILOT LIGHTS FOR SWITCHES NOTED WITH A "PU NEXT TO IT. PILOT LIGHTS ARE REQUIRED FOR ALL SWITCHES CONTROLLING LIGHTS FIXTURES THAT ARE NOT VISIBLE FROM SWITCH LOCATION. SWITCH BANK 1 1