|
POWER & COMMUNICATION NOTES:
<br />1. PRIOR TO CORING SLAB, REVIEW LOCATIONS WITH ARCHITECT AND COORDINATE LOCATIONS WITH
<br />OWNER.
<br />2. COORDINATE INSTALLATION OF TELECOMMUNICATIONS, DATA AND SECURITY SYSTEMS.
<br />3. VERIFY EQUIPMENT SPECIFICATIONS, POWER AND INSTALLATION REQUIREMENTS WITH
<br />MANUFACTURER TO ENSURE PROPER FIT AND FUNCTION.
<br />4. VERIFY MOUNTING REQUIREMENTS OF ELECTRICAL, TELEPHONE AND OTHER EQUIPMENT.
<br />5. GANG ADJACENT LIGHT SWITCHES AND COVER WITH A SINGLE PLATE.
<br />6. PROVIDE LIGHT SWITCHING IN CONFORMANCE WITH TITLE 24 REQUIREMENTS. FOR ROOMS OR
<br />AREAS GREATER THAN 100 SQUARE FEET PROVIDE DOUBLE SWITCHES WITH EACH SWITCH
<br />CONTROLLING 50% OF LAMPS PER FIXTURE.
<br />7. MOUNT STANDARD WALL OUTLETS, SWITCHES AND THERMOSTATS AT HEIGHTS REQUIRED BY
<br />TITLE 24 AND ADA GUIDELINES, UNLESS OTHERWISE NOTED. WHEN THERMOSTATS AND LIGHT
<br />SWITCH OCCUR TOGETHER, INSTALL BOTH ALIGNED HORIZONTALLY WITH CENTER LINE AT + 3'- 2"
<br />ABOVE FINISHED FLOOR.
<br />8. INDICATED DIMENSIONS ARE TO THE CENTER LINE OF OUTLET OR SWITCH, OR CLUSTER OF
<br />OUTLETS OR SWITCHES, UNLESS OTHERWISE NOTED.
<br />9. INSTALL OUTLETS ON OPPOSITE SIDES OF PARTITIONS IN SEPARATE STUD CAVITIES. DO NOT
<br />INSTALL BACK-TO-BACK.
<br />10. PROVIDE MATCHING COVER PLATES, RECEPTACLES AND RELATED ITEMS. PROVIDE ONE-PIECE
<br />TYPE GANG COVER PLATES, UNLESS OTHERWISE NOTED.
<br />11. IDENTIFY DEDICATED OR ISOLATED GROUND ELECTRICAL OUTLETS WITH A RED DOT
<br />FLOOR PLAN NOTES:
<br />1. ALL DIMENSIONS SHOWN ARE TO FINISHED FACE UNLESS NOTED OTHERWISE.
<br />2. ALL EXTERIOR DIMENSIONS ARE MASONRY OPENINGS UNLESS NOTED OTHERWISE.
<br />3. ALL DOORS SHALL BE LOCATED 4" FROM ADJACENT WALLS UNLESS DIMENSIONED OTHERWISE.
<br />4. REFER TO ENLARGED PLANS FOR DIMENSIONS & PARTITION TYPES OF THOSE PARTICULAR AREAS.
<br />5. CLEAN, PATCH, & REPAIR EXISTING WALLS, FLOORS, & CEILINGS AS REQUIRED FOR NEW FINISHES/NEW
<br />WORK.
<br />6. COORDINATE SAWCUT TRENCHING FOR NEW MEP ITEMS WITH MEP SHEETS. CUT & REMOVE CONCRETE IN
<br />CONTINUOUS STRAIGHT LINES. DISPOSE OF DEBRIS IN PROPER CONTAINER & REMOVE OFFSITE. BACKFILL
<br />& COMPACT PER SPECIFICATIONS. INFILL OPENINGS IN SLAB WITH CONCRETE & PROVIDE CONCRETE
<br />SEALER: QUICKCRETE ACRYLIC #8500 ON FINISH SLAB OR FACE.
<br />7. PATCH, REPAIR, OR REPLACE DAMAGED GYPSUM WALL BOARD ON EXISTING METAL FRAMING.
<br />8. REFER TO SHEET D1 (BY OTHERS) TO LOCATE NEW OR RELOCATED EQUIPMENT.
<br />9. CONTRACTOR TO COORDINATE PHASING WITH STORE OWNER TO ALLOW STORE TO REMAIN IN
<br />OPERATION DURING CONSTRUCTION.
<br />10. DAMAGED CONSTRUCTION (NEW OR EXISTING) SHALL BE REPAIRED, REPLACED, AND/OR MODIFIED
<br />AS DETERMINED BY THE OWNER'S REPRESENTATIVE.
<br />11. WHERE THE VERTICAL SPAN OF METAL STUDS EXCEEDS 15'-0", SPACING SHALL BE 16" O.C. IN LIEU OF
<br />24" O.C.
<br />12. CONTRACTOR SHALL BE REQUIRED TO CONFIRM THE PRESENCE OF AN UNDERSLAB VAPOR BARRIER
<br />(BENEATH EXISTING SLAB ON GRADE). THE CONTRACTOR MY UTILIZE SCOPE REQUIRED FLOOR
<br />TRENCHING AS A MEANS OF "VISUALLY" CONFIRMING THE EXISTENCE OF VAPOR BARRIER, OR
<br />CONTRACTOR MAY PERFORM A MINIMUM OF THREE (3) RELATIVE HUMIDITY FLOOR PROBES PER
<br />ASTM F2170. REPORT RESULTS OF FINDINGS TO ARCHITECT.
<br />13. ALL DOORS WITHOUT DOOR TAGS ARE EXISTING TO REMAIN.
<br />14. EXISTING TO REMAIN OBJECTS SHOWN GRAYED -OUT. TYPICAL.
<br />ACCESSIBILITY NOTES:
<br />1. IN BUILDINGS AND FACILITIES, FLOORS OF A GIVEN STORY SHALL BE A COMMON LEVEL
<br />THROUGHOUT, OR SHALL BE CONNECTED BY PEDESTRIAN RAMPS, PASSENGER ELEVATORS
<br />OR SPECIAL ACCESS LIFTS.
<br />2. FLOOR SURFACES SHALL BE SLIP -RESISTANT.
<br />3. EVERY CORRIDOR AND AISLE SERVING AN OCCUPANT LOAD OF 10 OR MORE SHALL BE NOT LESS
<br />THAN 44" IN WIDTH.
<br />4. ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE ROUTE SHALL NOT EXCEED 1/2" IN HEIGHT.
<br />LEVEL CHANGES NOT EXCEEDING 1/4" MAY BE VERTICAL. BEVEL OTHERS WITH A SLOPE NO
<br />GREATER THAN 1:2.
<br />5. LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND WHICH ARE IN A PATH OF
<br />TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE HARDWARE, PANIC BARS,
<br />PUSH-PULL ACTIVATING BARS, OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE
<br />WITHOUT REQUIRING THE ABILITY TO GRASP THE OPENING HARDWARE. MOUNT DOOR OPENING
<br />HARDWARE BETWEEN 30" AND 44" ABOVE FLOOR FINISH.
<br />6. CENTER HAND ACTIVATED DOOR OPENING HARDWARE BETWEEN 30" AND 44" ABOVE THE
<br />FLOOR.
<br />7. MAXIMUM PULL OR PUSH EFFORT TO OPERATE DOORS SHALL NOT EXCEED 8.5 POUNDS FOR
<br />EXTERIOR DOORS AND 5 POUNDS FOR INTERIOR DOORS, MEASURED AT RIGHT ANGLES TO
<br />HINGED DOORS AND AT CENTER PLANE OF SLIDING OR FOLDING DOORS. CORRESPONDING
<br />DEVICES OR AUTOMATIC DOOR OPERATORS MAY BE UTILIZED TO MEET THE ABOVE STANDARDS.
<br />MAXIMUM EFFORT TO OPERATE REQUIRED FIRE DOORS MAY BE INCREASED NOT TO EXCEED 15
<br />POUNDS.
<br />8. THE BOTTOM 10" OF ALL DOORS (EXCEPT SLIDING AND AUTOMATIC) SHALL HAVE A SMOOTH
<br />UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST
<br />WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION. PROVIDE A 10" HIGH SMOOTH PANEL ON
<br />THE PUSH SIDE OF NARROW FRAME DOORS.
<br />9. EVERY REQUIRED ENTRANCE OR PASSAGE DOORWAY SHALL BE NOT LESS THAN 3' IN WIDTH AND
<br />NOT LESS THAN 6'-8" IN HEIGHT. DOORS SHALL BE CAPABLE OF OPENING AT LEAST 90 DEGREES
<br />AND SHALL BE SO MOUNTED THAT THE CLEAR WIDTH OF THE DOORWAY IS NOT LESS THAN 32".
<br />10. WHERE A PAIR OF DOORS IS UTILIZED, AT LEAST ONE OF THE DOORS SHALL PROVIDE A CLEAR,
<br />UNOBSTRUCTED OPENING WIDTH OF 32" WITH THE LEAF POSITIONED AT AN ANGLE OF 90 DEGREES
<br />FROM ITS CLOSED POSITION.
<br />11. IDENTIFY ACCESSIBLE ENTRANCES WITH AT LEAST ONE STANDARD SIGN AND WITH ADDITIONAL
<br />DIRECTIONAL SIGNS, AS REQUIRED, VISIBLE FROM APPROACHING PEDESTRIAN WAYS.
<br />12. THE FLOOR OR LANDING ON EACH SIDE OF AN ENTRANCE OR PASSAGE DOOR SHALL BE LEVEL AND
<br />CLEAR. THE LEVEL AND CLEAR AREA SHALL HAVE A LENGTH IN THE DIRECTION OF DOOR SWING OF AT
<br />LEAST 60" AND THE LENGTH OPPOSITE THE DIRECTION OF DOOR SWING OF 44" AS MEASURED AT
<br />RIGHT ANGLES TO THE PLANE OF THE DOOR IN ITS CLOSED POSITION.
<br />13. FLOORS OR LANDINGS SHALL BE NOT MORE THAN 1/2" LOWER THAN THE THRESHOLD OF THE
<br />DOORWAY. CHANGE IN LEVEL BETWEEN 1/4" AND 1/2" SHALL BE BEVELED WITH A SLOPE NO
<br />GREATER THAN 1:2.
<br />14. TO ALERT THE VISUALLY IMPAIRED, MARK THE UPPER APPROACH AND THE LOWER TREAD OF EACH
<br />INTERIOR STAIR WITH A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2" WIDE, PLACED
<br />PARALLEL TO AND NOT MORE THAN V FROM THE NOSE OF THE STEP OR LANDING. THE STRIP SHALL
<br />BE OF A MATERIAL THAT IS AT LEAST AS SLIP RESISTANT AS THE OTHER TREADS OF THE STAIR.
<br />15. CENTER ELECTRICAL RECEPTACLE OUTLETS NOT LESS THAN 15" ABOVE THE FLOOR OR
<br />WORKING PLATFORM.
<br />16. SANITARY FACILITIES LOCATED ON AN ACCESSIBLE FLOOR OF A BUILDING SHALL BE
<br />ACCESSIBLE TO THE PHYSICALLY HANDICAPPED.
<br />17. ENTRY TO SANITARY FACILITIES:
<br />17.1. A. 44" CLEAR AISLES OR CORRIDORS WHERE OCCUPANT LOAD IS 10 OR MORE.
<br />17.2. DOORWAYS TO HAVE A 32" CLEAR OPENING.
<br />17.3. ON APPROACH SIDE, PROVIDE A 60" CLEAR LEVEL SPACE WHEN DOOR SWINGS TOWARD
<br />APPROACH AND 44" SPACE WHEN DOOR SWINGS AWAY FROM APPROACH.
<br />18. TOILET ROOM ACCESSORIES
<br />18.1. MOUNT BOTTOM EDGE MIRRORS NO HIGHER THAN 40" FROM THE FLOOR.
<br />18.2. MOUNT TOILET TISSUE DISPENSERS WITHIN 12" FROM THE FRONT EDGE OF THE TOILET
<br />SEAT.
<br />18.3. MOUNT DISPENSING AND DISPOSAL FIXTURES (TOWEL, SANITARY NAPKINS, WASTE, COIN
<br />SLOTS, ETC. WITH OPERATING PARTS NO HIGHER THAN 40" FROM THE FLOOR.
<br />19. SINGLE ACCOMMODATION TOILET FACILITY
<br />19.1. WATER CLOSET TO HAVE A 28" CLEARANCE FROM A FIXTURE & 32" FROM A WALL
<br />19.2• MINIMUM CLEAR SPACE IN FRONT OF WATER CLOSET TO BE 48".
<br />19.3. AN ACCESSIBLE 36"x48" SPACE IS PERMITTED IN FRONT OF EXISTING WATER CLOSET.
<br />20. THE HEIGHT OF THE WATER CLOSET (TOP OF SEAT) SHALL BE BETWEEN 17" MIN. & 19" MAX.
<br />21. MOUNT FLUSH VALVE CONTROL NO MORE THAN 44" ABOVE THE FLOOR, ON THE SIDE OF THE
<br />TOILET WITH THE GREATEST SEPARATION FROM ADJACENT WALL OR OTHER SURFACE.
<br />22. PROVIDE GRAB BARS ON EACH SIDE, OR ONE SIDE AND BACK OF WATER CLOSET..
<br />22.1. GRAB BARS TO BE 33" ABOVE AND PARALLEL TO FLOOR.
<br />22.2. SIDE BARS TO BE 42" LONG AND PROJECT 24" IN FRONT OF WATER CLOSET STOOL. GRAB
<br />BAR AT BACK TO BE 36" LONG.
<br />22.3. DIAMETER OF GRAB BARS TO BE 1-1/4" TO 1-1/2".
<br />22.4. PROVIDE 1-1/2" CLEARANCE BETWEEN GRAB BARS & WALL.
<br />22.5. GRAB BARS (INCLUDING CONNECTORS, FASTENERS, SUPPORT BACKING, ETC.) SHALL
<br />SUPPORT A MIN. 250 POUND LOAD.
<br />22.6. GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.
<br />22.7. GRAB BARS AND ANY ADJACENT SURFACE SHALL BE FREE OF SHARP OR ABRASIVE ELEMENTS.
<br />22.8. EDGES SHALL HAVE A MINIMUM RADIUS OF 1/8".
<br />23. PROVIDE A MINIMUM 30"x48" CLEAR FLOOR SPACE IN FRONT OF LAVATORY TO PERMIT A
<br />FORWARD APPROACH.
<br />24. MOUNT LAVATORIES WITH A MINIMUM CLEARANCE OF 29" FROM THE FLOOR TO THE BOTTOM OF
<br />APRON. PROVIDE KNEE CLEARANCES UNDER THE FRONT LIP EXTENDING A MINIMUM OF 30" IN
<br />WIDTH WITH 8" MINIMUM WIDTH, AND SHALL BE A MINIMUM OF 9" HIGH FROM THE FLOOR A
<br />MINIMUM F 17" DEEP FROM THE FRONT OF THE LAVATORY.
<br />25. FAUCET CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND
<br />SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE
<br />REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 POUNDS. LEVER OPERATED,
<br />PUSH TYPE, AND ELECTRONICALLY CONTROLLED MECHANISMS ARE EXAMPLES OF ACCEPTABLE
<br />DESIGNS. SELF CLOSING ARE ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10 SECONDS.
<br />26. INSULATE OR OTHERWISE COVER HOT WATER & DRAINPIPES UNDER ALL LAVATORIES.
<br />27. THERE SHALL BE NO SHARP OR ABRASIVE SURFACES UNDER LAVATORIES.
<br />REFLECTED CEILING NOTES:
<br />1. DESIGN SUSPENDED CEILING FRAMING SYSTEMS TO RESIST A LATERAL FORCE OF 20 % OF THE
<br />WEIGHT OF THE CEILING ASSEMBLY AND ANY LOADS TRIBUTARY TO THE SYSTEM. USE A
<br />MINIMUM CEILING WEIGHT OF 5 POUNDS PER SQUARE FOOT TO DETERMINE THE LATERAL
<br />FORCE.
<br />2. WHERE CEILING LOADS DO NOT EXCEED 5 POUNDS PER SQUARE FOOT AND WHERE PARTITIONS
<br />ARE NOT CONNECTED TO THE CEILING SYSTEM, THE FOLLOWING BRACING METHODS MAY BE
<br />EMPLOYED:
<br />2.1. PROVIDE LATERAL SUPPORT BY FOUR WIRES OF MINIMUM NO. 12 GAUGE SPLAYED IN FOUR
<br />DIRECTIONS 90 DEGREES APART, AND CONNECTED TO THE MAIN RUNNER WITHIN 2" OF THE
<br />CROSS RUNNER AND TO THE STRUCTURE ABOVE AT AN ANGLE NOT EXCEEDING 45 DEGREES
<br />FROM THE PLANE OF THE CEILING. PROVIDE THESE LATERAL SUPPORT POINTS 12 FEET ON
<br />CENTER IN EACH DIRECTION, WITH THE FIRST POINT WITHIN 4' FROM EACH WALL.
<br />2.2. ALLOW FOR LATERAL MOVEMENT OF THE SYSTEM. ATTACH MAIN RUNNERS AND CROSS
<br />RUNNERS AT TWO ADJACENT WALLS; MAINTAIN CLEARANCE BETWEEN THE WALL AND THE
<br />RUNNERS AT THE OTHER TWO WALLS.
<br />2.3. PROVIDE VERTICAL SUPPORT AS REQUIRED IN BUILDING CODES. IN ADDITION, VERTICALLY
<br />SUPPORT ENDS OF RUNNERS WITHIN 8" OF DISCONTINUITIES SUCH AS MAY OCCUR WHERE
<br />THE CEILING IS INTERRUPTED BY A WALL.
<br />2.4. SUPPORT LIGHT FIXTURES AND AIR DIFFUSERS DIRECTLY BY WIRES TO THE STRUCTURE
<br />ABOVE.
<br />3. LOCATE REGISTERS AND LIGHTING FIXTURES WITHIN GRID LINES. CENTER SPRINKLER HEADS,
<br />SPEAKERS, RECESSED FIXTURES, AND SIMILAR CEILING ELEMENTS IN ACOUSTICAL UNITS,
<br />UNLESS OTHERWISE NOTED.
<br />4. FINISH HVAC DIFFUSERS, DRAPERY POCKETS, AND SPEAKER GRILLES TO MATCH ADJACENT
<br />FINISH, UNLESS OTHERWISE NOTED.
<br />FIRE DEPARTMENT NOTES:
<br />1. PROVIDE A PORTABLE FIRE EXTINGUISHER WITH A RATING OF NOT LESS THAN 2-A WITHIN 75
<br />FOOT TRAVEL DISTANCE TO ALL PORTIONS OF THE BUILDING ON EACH FLOOR, AND
<br />ADDITIONAL EXTINGUISHERS AS REQUIRED BY FIRE DEPARTMENT FIELD INSPECTOR OR
<br />BUILDING DEPARTMENT INSPECTOR.
<br />2. PROVIDE EXIT SIGN WITH 6" LETTERS OVER REQUIRED EXITS, WHERE SHOWN ON DRAWINGS,
<br />AND ADDITIONAL SIGNS AS REQUIRED BY BUILDING DEPARTMENT INSPECTOR OR FIRE
<br />DEPARTMENT FIELD INSPECTOR. CONNECT EXIT SIGNS TO EMERGENCY POWER CIRCUITS.
<br />COMPLY WITH BUILDING CODES.
<br />3. PROVIDE EMERGENCY LIGHTING OF ONE FOOT-CANDLE AT FLOOR LEVEL. COMPLY WITH
<br />BUILDING CODES.
<br />4. MAINTAIN AISLES AT LEAST 44" WIDE AT PUBLIC AREAS.
<br />5. EVERY EXIT DOOR SHALL BE OPERABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY
<br />SPECIAL KNOWLEDGE OR EFFORT. SPECIAL LOCKING DEVICES SHALL BE OF AN APPROVED
<br />TYPE. ALL NEW DOORS SHALL HAVE APPROVED LEVER HANDLES.
<br />6. DOORS OPENING INTO REQUIRED 1-HOUR, FIRE -RESISTIVE CORRIDORS SHALL BE PROTECTED
<br />WITH A SMOKE OR DRAFT STOP ASSEMBLY HAVING A 20-MINUTE RATING AND SHALL BE SELF -
<br />CLOSING.
<br />7. 20-MINUTE DOOR JAMBS TO BE TIGHT -FITTING, SMOKE AND DRAFT CONTROLLED.
<br />8. EXIT DOORS SHALL SWING IN THE DIRECTION OF TRAVEL WHEN SERVING 50 OR MORE PERSONS
<br />AND IN ANY HAZARDOUS AREA.
<br />9. INTERIOR WALL AND CEILING FINISHES FOR EXIT CORRIDOR SHALL NOT EXCEED AN END POINT
<br />FLAME SPREAD RATING: A. CLASS I, FLAME SPREAD 0-25, SMOKE DENSITY 150, FOR MATERIALS
<br />INSTALLED IN VERTICAL EXITS. B. CLASS II, FLAME SPREAD 26-75, SMOKE DENSITY 300, FOR
<br />MATERIALS INSTALLED IN HORIZONTAL EXITS. C. CLASS III, FLAME SPREAD 76-200, SMOKE
<br />DENSITY 450, FOR MATERIALS INSTALLED IN ANY OTHER LOCATION.
<br />10. DECORATIONS (CURTAINS, DRAPES, SHADES, HANGINGS, ETC.) SHALL BE NON-COMBUSTIBLE
<br />OR BE FLAMEPROOFED IN AN APPROVED MANNER.
<br />11. PROVIDE FIRE DAMPERS OR DOORS WHERE AIR DUCTS PENETRATE FIRE -RATED WALLS OR
<br />CEILINGS.
<br />12. STORAGE, DISPENSING OR USE OF ANY FLAMMABLE OR COMBUSTIBLE LIQUIDS, FLAMMABLE GAS
<br />AND HAZARDOUS SUBSTANCES SHALL COMPLY WITH UNIFORM FIRE CODE REGULATIONS.
<br />13. WOOD BLOCKING SHALL BE FIRE TREATED IN ACCORDANCE WITH APPLICABLE CODE
<br />REQUIREMENTS.
<br />14. EXTEND OR MODIFY EXISTING FIRE/LIFE SAFETY SYSTEM AS REQUIRED TO PROVIDE AN APPROVED
<br />FIRE/ LIFE SAFETY SYSTEM. SUBMIT PLANS TO FIRE DEPARTMENT WITH COMPLETE DESCRIPTION
<br />OF SEQUENCE OF OPERATION, AND OBTAIN APPROVAL PRIOR TO INSTALLATION.
<br />15. LOCATE THE CENTER OF FIRE ALARM INITIATING DEVICES 48" ABOVE THE LEVEL OF THE FLOOR,
<br />WORKING PLATFORM, GROUND SURFACE OR SIDEWALK.
<br />16. EMERGENCY WARNING SYSTEMS SHALL ACTIVATE A MEANS OF WARNING THE HEARING IMPAIRED.
<br />FLASHING VISUAL WARNING SHALL HAVE A FREQUENCY OF NOT MORE THAN 60 FLASHES PER
<br />MINUTE.
<br />17. EXTEND OR MODIFY EXISTING AUTOMATIC FIRE EXTINGUISHING SYSTEM AS REQUIRED TO
<br />PROVIDE AN APPROVED AUTOMATIC FIRE EXTINGUISHING SYSTEM. SUBMIT PLANS TO FIRE
<br />DEPARTMENT AND OBTAIN APPROVAL PRIOR TO INSTALLATION.
<br />18. AUTOMATIC SPRINKLER SYSTEMS SHALL BE SUPERVISED BY AN APPROVED CENTRAL,
<br />PROPRIETARY OR REMOTE STATION SERVICE OR A LOCAL ALARM WHICH WILL GIVE AN
<br />AUDIBLE SIGNAL AT A CONSTANTLY ATTENDED LOCATION.
<br />GENERAL NOTES:
<br />1. COMPLY WITH CODES, LAWS, ORDINANCES, RULES, AND REGULATIONS OF PUBLIC AUTHORITIES
<br />GOVERNING THE WORK.
<br />2. OBTAIN AND PAY FOR PERMITS AND INSPECTIONS REQUIRED BY PUBLIC AUTHORITIES GOVERNING
<br />THE WORK.
<br />3. REVIEW DOCUMENTS, VERIFY DIMENSIONS AND FIELD CONDITIONS AND CONFIRM THAT WORK IS
<br />BUILDABLE AS SHOWN. REPORT ANY CONFLICTS OR OMISSIONS TO THE ARCHITECT FOR
<br />CLARIFICATION PRIOR TO PERFORMING ANY WORK IN QUESTION.
<br />4. SUBMIT REQUESTS FOR SUBSTITUTIONS, REVISIONS, OR CHANGES TO ARCHITECT FOR REVIEW
<br />PRIOR TO PURCHASE, FABRICATION OR INSTALLATION.
<br />5. COORDINATE WORK WITH THE OWNER, INCLUDING SCHEDULING TIME AND LOCATIONS FOR
<br />DELIVERIES, BUILDING ACCESS, USE OF BUILDING SERVICES AND FACILITIES, AND USE OF
<br />ELEVATORS. MINIMIZE DISTURBANCE OF BUILDING FUNCTIONS AND OCCUPANTS.
<br />6. OWNER WILL PROVIDE WORK NOTED "BY OTHERS" OR "NIC" UNDER SEPARATE CONTRACT.
<br />INCLUDE SCHEDULE REQUIREMENTS IN CONSTRUCTION PROGRESS SCHEDULE AND COORDINATE
<br />TO ASSURE ORDERLY SEQUENCE OF INSTALLATION.
<br />7. COORDINATE TELECOMMUNICATIONS, DATA AND SECURITY SYSTEM INSTALLATIONS.
<br />8. MAINTAIN EXITS, EXIT LIGHTING, FIRE PROTECTIVE DEVICES, AND ALARMS IN CONFORMANCE WITH
<br />CODES AND ORDINANCES.
<br />9. PROTECT AREA OF WORK AND ADJACENT AREAS FROM DAMAGE.
<br />10. MAINTAIN WORK AREAS SECURE AND LOCKABLE DURING CONSTRUCTION. COORDINATE WITH
<br />TENANT AND LANDLORD TO ENSURE SECURITY.
<br />11. DO NOT SCALE DRAWINGS. WRITTEN DIMENSIONS GOVERN. IN CASE OF CONFLICT, CONSULT
<br />THE ARCHITECT.
<br />12. PARTITIONS ARE DIMENSIONED FROM FINISH FACE TO FINISH FACE, UNLESS OTHERWISE NOTED.
<br />MAINTAIN DIMENSIONS MARKED "CLEAR". ALLOW FOR THICKNESS OF FINISHES.
<br />13. COORDINATE AND PROVIDE BACKING FOR MILLWORK AND ITEMS ATTACHED OR MOUNTED TO
<br />WALLS OR CEILINGS.
<br />14. WHERE EXISTING ACCESS PANELS CONFLICT WITH CONSTRUCTION, RELOCATE PANELS TO
<br />ALIGN WITH AND FIT WITHIN NEW CONSTRUCTION.
<br />15. UNDERCUT DOORS TO CLEAR TOP OF FLOOR FINISHES BY 1/4 INCH, UNLESS OTHERWISE NOTED.
<br />DEMOLITION NOTES:
<br />1. COMPLY WITH APPLICABLE LOCAL, STATE AND FEDERAL CODES AND REGULATIONS
<br />PERTAINING TO SAFETY OF PERSONS, PROPERTY AND ENVIRONMENTAL PROTECTION.
<br />2. PROVIDE AND MAINTAIN BARRICADES, LIGHTING, AND GUARDRAILS AS REQUIRED BY
<br />APPLICABLE CODES AND REGULATIONS TO PROTECT OCCUPANTS OF BUILDING AND
<br />WORKERS.
<br />3. ERECT AND MAINTAIN DUSTPROOF PARTITIONS AS REQUIRED TO PREVENT SPREAD OF DUST,
<br />FUMES, AND SMOKE, ETC. TO OTHER PARTS OF THE BUILDING. ON COMPLETION, REMOVE
<br />PARTITIONS AND REPAIR DAMAGED SURFACES TO MATCH ADJACENT SURFACES.
<br />4. IF DEMOLITION IS PERFORMED IN EXCESS OF THAT REQUIRED, RESTORE EFFECTED AREAS AT
<br />NO COST TO THE OWNER.
<br />5. REMOVE FROM SITE DAILY AND LEGALLY DISPOSE OF REFUSE, DEBRIS, RUBBISH, AND OTHER
<br />MATERIALS RESULTING FROM DEMOLITION OPERATIONS.
<br />6. REMOVE DESIGNATED PARTITIONS, COMPONENTS, BUILDING EQUIPMENT, AND FIXTURES AS
<br />REQUIRED FOR NEW WORK.
<br />7. REMOVE ABANDONED HVAC EQUIPMENT, INCLUDING DUCT WORK.
<br />8. REMOVE ABANDONED ELECTRICAL, TELEPHONE AND DATA CABLING AND DEVICES, UNLESS
<br />OTHERWISE NOTED.
<br />9. REMOVE EXISTING FLOOR FINISHES AND PREPARE SUBFLOOR AS REQUIRED FOR NEW FLOOR
<br />FINISHES.
<br />FINISH NOTES:
<br />1. ENSURE SURFACES TO RECEIVE FINISHES ARE CLEAN, TRUE, FREE OF IRREGULARITIES, & MEET
<br />REQUIREMENTS OF NEW FINISHES TO BE INSTALLED. DO NOT PROCEED WITH WORK UNTIL
<br />UNSATISFACTORY CONDITIONS HAVE BEEN CORRECTED.
<br />2. REPAIR EXISTING SURFACES TO REMAIN AS REQUIRED FOR APPLICATION OF NEW FINISHES.
<br />3. PROVIDE STRAIGHT, FLUSH RESILIENT BASE AT CARPETED AREAS, AND COVED, TOP SET
<br />RESILIENT BASE AT RESILIENT FLOORING, UNLESS OTHERWISE NOTED.
<br />•
<br />bee
<br />C.
<br />z z < o
<br />O n
<br />ZW�L6
<br />gzo�
<br />0
<br />WzJJ
<br />W
<br />UQoLLI
<br />,
<br />Q z U-
<br />LL
<br />(D w
<br />m w
<br />W p
<br />p
<br />p
<br />W wQ
<br />_ i�zLLcnp
<br />O o O
<br />Q
<br />wo
<br />�pzmw<ww 3 __xm
<br />WzOmpz�0_j
<br />UzQ W}O>-U=tip
<br />mgU��->=W�-ow
<br />LUId�<==X) Wti
<br />W w ucLW W cm Q U p Q z Q
<br />=F_U)i15- mZ)U)<QDcwwU)i)
<br />z
<br />O_
<br />a
<br />� tr
<br />� U
<br />W
<br />IL W
<br />0 p U)
<br />m z
<br />Ix O
<br />O (n
<br />p >
<br />W ui
<br />m
<br />0 �-
<br />p m
<br />N W
<br />0
<br />fM
<br />0
<br />or"
<br />CV
<br />IT
<br />IT
<br />Lo
<br />Z> c)
<br />L JU-
<br />Lo
<br />O
<br />CD
<br />L
<br />� J
<br />�
<br />W
<br />ffnn J
<br />o_
<br />W
<br />V
<br />cn
<br />O
<br />J rn
<br />0
<br />U)�
<br />�CL
<br />z
<br />L11
<br />J
<br />N
<br />W
<br />z
<br />W
<br />(U'
<br />Q
<br />uo
<br />CO
<br />C)CM N
<br />Lo
<br />pm
<br />N
<br />J O
<br />a Lo
<br />m
<br />Z
<br />M
<br />LLI
<br />� o
<br />W
<br />W
<br />cl
<br />XCD
<br />QaN�o
<br />Q
<br />Wcn
<br />U v
<br />0 p
<br />0
<br />X 0
<br />G-030
<br />L,UF'Y MUM I U LU"10 UtNJLtK
<br />
|