|
ELECTRICAL SPECIFICATIONS
<br />I. SCOPE OF WORK
<br />A. ALL WORK SHALL BE IN COMPLIANCE WITH THE LATEST APPLICABLE CODES, LAWS AND ORDINANCES,
<br />AND THE NATIONAL ELECTRICAL CODE. PROVIDE AND FURNISH ALL LABOR, MATERIALS, PERMITS, AND
<br />INCIDENTALS REQUIRED TO COMPLETE ALL WORK AS SHOWN ON CONTRACT DOCUMENTS.
<br />B. CONTRACTOR SHALL INSPECT ALL NEW MATERIAL AND EQUIPMENT PRIOR TO INSTALLATIONS FOR
<br />DAMAGES, AND SHALL VERIFY EQUIPMENT OPERATES SATISFACTORILY.
<br />C. CONTRACTOR SHALL WARRANT ALL MATERIAL AND EQUIPMENT FURNISHED TO COMPLETE ALL WORK
<br />FOR ONE YEAR AFTER FINAL ACCEPTANCE OF COMPLETION. MATERIALS AND EQUIPMENT DEFECTS OF
<br />FAILURES DUE TO ABUSE, OR WORKMANSHIP NEGLECT SHALL BE MADE GOOD BY THE CONTRACTOR
<br />WITHOUT COST TO THE OWNER.
<br />D. PROVIDE ONLY NEW, STANDARD UNDERWRITER'S LABORATORY INC. LISTED FIRST -GRADE MATERIALS
<br />THROUGHOUT, AND SHALL BE MARKED WITH UNDERWRITER'S LABORATORY INC. LISTED AND WITH
<br />MANUFACTURER'S BRAND OR TRADEMARK. ALL MATERIALS SHALL BE OF ONE MANUFACTURER.
<br />E. CONTRACTOR SHALL BE EXPERIENCED IN THEIR TRADE. CONTRACTOR'S WORK SHALL PRESENT A
<br />NEAT APPEARANCE UPON COMPLETION. MATERIALS AND EQUIPMENT INSTALLED SHALL BE PLUMB,
<br />STRAIGHT, AND LEVEL
<br />F. CONTRACTOR SHALL COORDINATE WITH THE ARCHITECT AND OWNER ON EXACT LOCATION OF WIRING
<br />DEVICES AND RACEWAY FOR OWNER -FURNISHED EQUIPMENT PRIOR TO ROUGH -IN.
<br />G. UPON COMPLETION OF WORK, THE CONTRACTOR SHALL TEST ALL WIRING AND EQUIPMENT
<br />INSTALLATION, AND SHALL BE IN PERFECT WORKING CONDITION IN ACCORDANCE WITH THE INTENT OF
<br />THE CONTRACT DOCUMENTS.
<br />II. ELECTRICAL IDENTIFICATION
<br />A. NAMEPLATES:
<br />ENGRAVED PLASTIC LAMINATE NAMEPLATES: PROVIDE ENGRAVING PHENOLIC PLASTIC LAMINATE, IN
<br />SIZES AND THICKNESS INDICATED, ENGRAVED WITH 1/16 INCH THICK LINES WITH SQUARE STANDARD
<br />PICA LETTERING AND WORDING AS SPECIFIED HEREIN, BLACK FACE AND WHITE LETTER FOR NORMAL
<br />SYSTEMS AND RED AND WHITE FOR FIRE ALARM AND WHERE NOTED IN THE SPECIFICATIONS. PUNCH
<br />FOR MECHANICAL FASTENING, EXCEPT WHERE ADHESIVE MOUNTING IS NECESSARY BECAUSE OF
<br />SUBSTRATE. MATERIAL THICKNESS SHALL BE 1 /16 INCH. PROVIDE BEVELED EDGE IN ORDER TO
<br />ELIMINATE SHARP CORNERS. PROVIDE SELF -TAPPING STAINLESS STAINLESS STEEL ROUND HEAD
<br />SCREWS. PROVIDE CONTACT TYPE PERMANENT ADHESIVE WHERE SCREWS CANNOT OR SHALL NOT
<br />PENETRATE THE SUBSTRATE. ADHESIVE NAMEPLATE SHALL BE PERMANENTLY INSTALLED. TITLES SHALL
<br />BE 1/2 INCH HIGH AND ALL OTHER LETTERING SHALL BE 1/4 INCH HIGH.
<br />B. JUNCTION BOXES:
<br />JUNCTION BOX IDENTIFICATION: PROVIDE NEAT INDELIBLE FELT TIP, STENCILED MARKING ON JUNCTION
<br />BOXES AND PULL BOX COVERS. LETTER SIZES SHALL BE 1 INCH HIGH MINIMUM. PROVIDE
<br />NON -STENCILED MARKINGS INSIDE THE JUNCTION BOX AND ON THE EXTERIOR EDGE TO MATCH THE
<br />COVER MARKINGS.
<br />III. BASIC MATERIALS AND METHODS
<br />A. PANEL BOARDS:
<br />PROVIDE PANEL BOARDS WITH MAIN BREAKER OR MAIN LUGS WHERE SHOWN ON THE DRAWINGS, OF A
<br />DEAD FRONT, DISTRIBUTED PHASE SEQUENCE DESIGN. PANEL BOARDS SHALL BE EQUIPPED WITH
<br />THERMAL -MAGNETIC MOLDED CASE CIRCUIT BREAKERS WITH FRAME AND TRIP RATINGS AS INDICATED IN
<br />THE SCHEDULES.
<br />DIRECTORIES: A TYPED PANEL BOARD DIRECTORY SHALL BE PROVIDED FOR EACH PANEL BOARD AND
<br />SHALL INDICATE THE ACTUAL CIRCUIT NUMBER USED, ROOM NAME AND TYPE OF LOAD. ROOM NAMES
<br />SHALL BE THE ACTUAL NAME OR ROOM NUMBER USED NOT NECESSARILY AS SHOWN ON THE DRAWING.
<br />PANEL DIRECTORIES SHALL INCLUDE ALL ROOM NUMBERS AND NAMES. WHERE PANEL SCHEDULES ARE
<br />INDICATED ON THE DRAWINGS AS "RECEPTACLES OR "UGHTING ETC, IT SHALL BE THE RESPONSIBILITY
<br />OF THE CONTRACTOR TO INCLUDE THE SPECIFIC AREA SERVED.
<br />B. CIRCUIT BREAKERS:
<br />CIRCUIT BREAKERS SHALL BE BOLT -ON QUICK -MAKE, QUICK -BREAK THERMAL -MAGNETIC TYPE, FOR
<br />ALTERNATING CURRENT. BREAKERS SHALL TRIP FREE OF THE HANDLE AND TRIPPING SHALL BE
<br />INDICATED BY THE HANDLE ASSUMING A POSITION BETWEEN OFF AND ON. MULTI- POLE BREAKERS
<br />SHALL BE INTERNAL, COMMON TRIP WITH SINGLE OPERATING HANDLE; EXTERNAL HANDLE TIES ARE NOT
<br />ACCEPTABLE.
<br />C. CONDUIT:
<br />RIGID SHALL BE MINIMUM 1", GALVANIZED OUTSIDE AND INSIDE BY HOT DIPPING, E.M.T. SHALL
<br />BE MINIMUM 1/2" AND SHALL BE ELECTRO-GALVANIZED. CONDUITS SHALL BE AS
<br />MANUFACTURED BY REPUBLIC, PITTSBURGH STANDARD, WHEATLAND, TRIANGLE, ALLIED, OR
<br />YOUNGSTOWN.
<br />TYPE "MC" CABLE IS ACCEPTABLE FOR BRANCH CIRCUIT WIRING. TYPE "MC" CABLE IS ACCEPTABLE
<br />TO MAKE FINAL CONNECTIONS FROM SOURCE JUNCTION BOXES TO LIGHT FIXTURES, MAXIMUM
<br />LENGTH 6'-0" (DO NOT DAISY CHAIN).
<br />PROVIDE END BUSHINGS ON ALL CONDUITS. PROVIDE PULL STRINGS IN ALL EMPTY RACEWAYS.
<br />PULL STRINGS SHALL BE NYLON AND SHALL BE IMPERVIOUS TO MOISTURE. PULL STRINGS SHALL
<br />HAVE A TENSILE STRENGTH NOT LESS THAN 200 LBS.
<br />CONDUIT ABOVE GRADE SHALL BE EMT (INTERIOR ONLY), IMC, OR GALVANIZED.
<br />CONDUIT BELOW GRADE SHALL BE RIGID GALVANIZED (HEAVY WALL), IMC, OR PVC (SCHEDULE 40).
<br />SEALANT. PROVIDE A CLOSED CELL SILICONE FOAM SEALANT RATED TO PROVIDE A RATING
<br />EQUAL TO THE WALL, CEILING, OR FLOOR ASSEMBLY RATING. PROVIDE SEALS FOR THE EXTERIOR
<br />OF CONDUIT PENETRATIONS CONSISTING OF A CAST -IN -PLACE SLEEVE WITH A COMPRESSIBLE
<br />RUBBER GASKET BETWEEN THE CONDUIT AND THE SLEEVE. PROVIDE SEALS FOR THE INTERIOR
<br />OF THE CONDUIT PENETRATIONS CONSISTING OF GLAND TYPE SEALING BUSHING OR CLOSED CELL
<br />SILICONE FOAM. PROVIDE DUCT SEAL INSIDE AN APPROPRIATE SEAL -OFF FITTING TO SEAL THE
<br />INTERIOR OF THE CONDUIT SYSTEM FROM WATER SEEPAGE OR HAZARDOUS GASES.
<br />D. ALL COUPLINGS AND CONNECTORS FOR EMT SHALL BE OF COMPRESSION TYPE.
<br />E. OUTLET BOXES:
<br />SHALL BE STANDARD TYPE, WITH KNOCKOUTS, MADE OF HOT DIPPED GALVANIZED STEEL AS
<br />MANUFACTURED BY STEEL CITY, RACO OR APPLETON.
<br />CEILING OUTLET BOXES SHALL BE 4-INCH OCTAGON 1-1/2 INCH DEEP OR LARGER WHEN
<br />REQUIRED DUE FOR NUMBER OF CONDUCTORS OR CONDUIT ENTRY.
<br />BOXES SHALL BE PROVIDED WITH APPROVED 3/8 INCH FIXTURE STUDS WHERE REQUIRED.
<br />PROVIDE JUNCTION OR PULL BOXES WHERE SHOWN ON THE DRAWINGS AS REQUIRED TO
<br />FACILITATE INSTALLING CONDUCTORS. SUCH BOXES SHALL BE "CODE" SIZED. ALL JUNCTION
<br />BOXES SHALL BE ACCESSIBLE.
<br />F. WIRE AND CABLE 600 VOLT:
<br />GENERAL: CONDUCTORS SHALL HAVE CURRENT CARRYING CAPACITIES AS PER N.E.C. AND WITH
<br />600 VOLT INSULATION, J12 MINIMUM EXCEPT FOR CONTROLS, AND FIXTURE WIRE. CONDUCTORS
<br />SHALL BE COPPER.
<br />GENERAL USE: #12 AND #10 SHALL BE SOLID, INSULATION TYPE THHN OR THWN.
<br />FEEDERS AND GENERAL USE: #8 AND LARGER AND ALL MOTORS CONDUCTORS SHALL BE
<br />STRANDED TYPE XHHW OR THWN.
<br />COLOR -CODING FOR CONDUCTORS SHALL BE CONSISTENT THROUGHOUT ENTIRE LENGTH. PHASE
<br />TAPE COLOR CODING IS NOT ACCEPTABLE. APPLIES TO FEEDERS AND BRANCH CIRCUIT
<br />CONDUCTORS OF ALL SIZES. COLOR CODING SHALL BE BLACK, RED, AND BLUE (WHITE NEUTRAL)
<br />FOR 120/208 VOLT 3-PHASE WIRING, AND BROWN, ORANGE, AND YELLOW (GREY NEUTRAL) FOR
<br />277/480 VOLT 3-PHASE WIRING. GROUND CONDUCTORS SHALL BE GREEN.
<br />G. BASIC DEVICES:
<br />PROVIDE IVORY COLORED DEVICES WHERE AVAILABLE, UNLESS OTHERWISE NOTED.
<br />20-AMP, 120/277 VAC, HEAVY DUTY, QUIET TYPE, SPECIFICATION GRADE:
<br />1. SINGLE POLE TOGGLE: PASS AND SEYMOUR NO. CS20AC1W.
<br />2. THREE-WAY TOGGLE: PASS AND SEYMOUR NO. CS20AC3W.
<br />RECEPTACLES:
<br />SPECIFICATION GRADE 20A, 125V, 2P, 3W GROUNDED, MOUNTED 18"AFF TO THE CENTERUNE
<br />UNLESS NOTED OTHERWISE. COLOR SHALL MATCH TOGGLE SWITCHES.
<br />1. 20A DUPLX, 3W, 125V, NEMA 5-20R LEVITON #5362
<br />PROVIDE CAST ALLOY OR STAMPED METAL PLATES ON EXPOSED SWITCHES AND RECEPTACLES.
<br />INSTALL DEVICE PLATES IN FULL CONTACT WITH WALL SURFACE. PLATES SHALL NOT PROJECT
<br />OUT FROM THE WALL.
<br />INSTALL DEVICE PLATES IN FULL CONTACT WITH SURFACE MOUNTED BOX. PLATES SHALL NOT
<br />PROJECT OUT FROM THE EDGE OF THE BOX.
<br />ALL DEVICE PLATES FOR RECEPTACLES AND SWITCHES SHALL BE LABELED. SHOW PANEL
<br />DESIGNATION AND BRANCH CIRCUIT SERVING EACH RECEPTACLE. USE ENGRAVED PLATES UNLESS
<br />OTHERWISE NOTED.
<br />ACCEPTABLE MANUFACTURERS: PASS do SEYMOUR, G.E., LEVITON
<br />H. SAFETY SWITCHES:
<br />GENERAL: ALL DISCONNECT SWITCHES SHALL BE HEAVY-DUTY TYPE, UNLESS SPECIFICALLY NOTED
<br />OTHERWISE. SWITCHES SHALL BE FUSIBLE OR NON -FUSIBLE AND SIZED AS NOTED ON THE DRAWINGS.
<br />SWITCHES SHALL BE 240 VOLT RATED ON SYSTEMS UP TO AND INCLUDING 120/24OV. ALL
<br />SWITCHES SERVING MOTOR LOADS SHALL BE HORSEPOWER RATED.
<br />PROVIDE SWITCHES WITH AN EXTERNALLY OPERATED HANDLE; QUICK MAKE QUICK BREAK MECHANISM;
<br />THE HANDLE SHALL BE INTERLOCKED WITH THE SWITCH COVER BY MEANS OF A DEFEATABLE
<br />INTERLOCK DEVICE. THE SWITCH SHALL BE LOCKABLE IN THE "OFF" POSITION WITH A PADLOCK.
<br />I. LIGHTING FIXTURES:
<br />LIGHTING FIXTURES SHALL BE FURNISHED AS SHOWN IN FIXTURE SCHEDULE. IT SHALL
<br />SPECIFICALLY BE THE RESPONSIBILITY OF THE CONTRACTOR TO VERIFY EXACT TYPE OF CEILING
<br />AND RECESSING DEPTH OF ALL RECESSED FIXTURES AND TO FURNISH THE MOUNTING TRIMS AND
<br />ACCESSORIES OF THE SPECIFIED AND/OR APPROVED FIXTURES FOR THE CEILING TO BE INSTALLED.
<br />FIXTURES SHALL BE SUPPORTED INDEPENDENTLY OF CEILING SYSTEMS.
<br />FLUORESCENT LAMPS SHALL BE T8, 28W, 3500 DEGREES K, 85 CRI MINIMUM.
<br />LAMP DESIGN SELECTION: OSRAM-SYLVANIA, GE, OR PHILLIPS.
<br />J. GROUNDING:
<br />GROUNDING SHALL BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND
<br />LOCAL CODES AND REQUIREMENTS.
<br />FEEDERS AND BRANCH CIRCUITS SHALL HAVE INSTALLED IN THE SAME RACEWAY AS THE
<br />CIRCUIT CONDUCTORS, AN INSULATED COPPER GROUNDING CONDUCTOR SIZED IN ACCORDANCE
<br />WITH NEC.
<br />DESCRIPTION OF SYSTEM: IN GENERAL, ALL ELECTRICAL EQUIPMENT (METALLIC CONDUIT, MOTOR
<br />FRAMES, PANEL BOARDS, ETC.) SHALL BE BONDED TOGETHER WITH A GREEN INSULATED OR
<br />BARE COPPER SYSTEM GROUNDING CONDUCTOR IN ACCORDANCE WITH SPECIFIC RULES OF
<br />ARTICLE 250 OF THE N.E.C. EQUIPMENT GROUNDING CONDUCTORS THROUGH THE RACEWAY
<br />SYSTEM SHALL BE CONTINUOUS FROM MAIN SWITCH GROUND BUS TO PANEL GROUND BAR OF
<br />EACH PANEL BOARD, AND FROM PANEL GROUNDING BAR OF EACH PANEL BOARD TO BRANCH
<br />CIRCUIT EQUIPMENT AND DEVICES.
<br />ADDITIONAL SENSORS
<br />WIRED IN SERIES IF
<br />REQUIRED
<br />MMAAXIIMUM NUMBER OF SENSORS PER POWER PACK
<br />DEPENDS ON THE MODEL OF SENSOR. SEE THE
<br />PRODUCT DATA SHEET TO DETERMINE THE SPECIFIC
<br />CURRENT CONSUMPTION OF EACH SENSOR.
<br />OCCUPANCY SENSOR DETAIL (LOW VOLTAGE
<br />N.T.S.
<br />LOCAL
<br />OFF
<br />A ', 1
<br />Line
<br />Ground
<br />Any Line
<br />Neutral
<br />Voltage
<br />Line
<br />Occupancy
<br />Load
<br />Sensor Using
<br />Terminals
<br />OCCUPANCY SENSOR DETAIL (LINE VOLTAGE
<br />N.T.S.
<br />PROVIDE A WALL MOUNTED DUAL TECHNOLOGY OCCUPANSCY SENSOR, MANUAL ON, IN EACH
<br />OFFICE TO CONTROL THE LIGHTS AUTOMATIC OFF WITHIN 30 MINUTES OF THE LAST OCCUPANT
<br />LEAVING THE SPACE: EQUAL TO WATT STOPPER DSW-200-W.
<br />CEILING OCCUPANCY SENSOR WHERE NOTED SHALL BE DUAL TECHNOLOGY TYPE EQUAL TO WATT
<br />STOPPER DT-300 SERIES TO CONTROL THE LIGHTS AUTOMATIC OFF WITHIN 30 MINUTES OF THE
<br />LAST OCCUPANT LEAVING THE SPACE.
<br />PROVIDE A 20 AMP RELAY ABOVE THE OCCUPANCY SENSOR SWITCH OR AT THE CEILING
<br />OCCUPANCY SENSOR, CONTROLLED WITH THE LIGHTS VIA THE OCCUPANCY SENSOR TO
<br />AUTOMATICCALY TURN OFF 50% OF THE RECEPTACLES WITHIN THE SPACE VIA N.O. CONTACTS.
<br />VERIFY WITH OWNER WHICH RECEPTACLES SHALL BE CONTROLLED WITH THE OCCUPANCY
<br />SENSOR. RECEPTACLE POWER SHALL BE CONTROLLED OFF WITHIN 30 MINUTES OF ALL
<br />OCCUPANTS LEAVING THE SPACE IN ACCORDANCE WITH FBC ENERGY CODE C405.7 AND ASHRAE
<br />90.1 SECTION 8.4.2 (b).
<br />TEST ALL WALL MOUNTED AND CEILING MOUNTED OCCUPANCY SENSORS IN ACCORDANCE WITH
<br />FBC ENERGY CODE C408.3 / C408.3.1
<br />ELECTRICAL SYMBOLS
<br />LEGEND
<br />LINEAR FLUORESCENT LIGHT FIXTURE - RECESSED
<br />,z 3P/60A 3R
<br />COMBINATION STARTER/DISCONNECT SWITCH,
<br />NORMAL POWER (NL - Night Light)
<br />NEMA 0
<br />SHOWN SIZE 3-POLE, 60 AMP, NEMA 0 RATED
<br />3R = NEMA 3R ENCLOSURE
<br />LINEAR FLUORESCENT LIGHT FIXTURE - RECESSED
<br />P A 3R
<br />DISCONNECT SWITCH, SHOWN SIZE - 2-POLE,
<br />HALF SHADED FOR EMERGENCY LIGHTING CIRCUIT
<br />F:50A
<br />60 AMP, FUSED AT 50 AMP. NF = NON -FUSED
<br />ON GENERATOR
<br />3R = NEMA 3R ENCLOSURE
<br />p
<br />DOWN LIGHT FIXTURE
<br />PANEL BOARD - FLUSH MOUNT, 240V AC
<br />®f
<br />EXIT LIGHT - SINGLE FACE W/
<br />PANEL BOARD - SURFACE MOUNT, ABOVE 240V AC
<br />DIRECTIONAL ARROW
<br />e
<br />EXIT LIGHT - DOUBLE FACE
<br />MOTOR CONNECTION. HP DENOTES HORSEPOWER RATING
<br />$
<br />SINGLE POLE TOGGLE SWITCH
<br />(LOWER CASE LETTER DENOTES FIXTURE CONTROLLED)
<br />I-QF
<br />FIRE ALARM STROBE ONLY DEVICE
<br />WITH MINIMUM 75CD RATING (LION) - 80" AFF TO
<br />$3
<br />THREE-WAY TOGGLE SWITCH
<br />BOTTOM OF DEVICE
<br />$os
<br />WALL SWITCH OCCUPANCY SENSOR
<br />FIRE ALARM COMBINATION AUDIBLE/STROBE DEVICE
<br />WATT STOPPER JDW-100 (DUAL TECH./SINGLE RELAY)
<br />WITH MINIMUM 75CD RATING (LION) - 80" AFF TO
<br />BOTTOM OF DEVICE
<br />$o
<br />DIMMER SWITCH
<br />®
<br />SMOKE DETECTOR - CEILING MOUNTED
<br />CEILING MOUNTED OCCUPANCY SENSOR
<br />WITH POWER PACK
<br />HOMERUN TO PANEL, NUMBER OF ARROWS
<br />DUPLEX RECEPTACLE
<br />INDICATE NUMBER CIRCUITS IN CONDUIT,
<br />DEDICATED NEUTRAL SHALL BE PROVIDED
<br />ggfi
<br />DUPLEX RECEPTACLE GROUND FAULT CIRCUIT INTERRUPTER
<br />IF MORE THAN ONE CIRCUIT.
<br />DUPLEX RECEPTACLE MOUNTED 48", UNLESS NOTED
<br />WIRE IN CONDUIT CONCEALED, #12AWG SIZEWIRE IN 3/4" CONDUIT MINIMUM, UNLESS
<br />OTHERWISE (TYPICAL FOR ALL RECEPTACLES)
<br />NOTED OTHERWISE
<br />QUADRUPLEX RECEPTACLE
<br />CONDUIT EXPOSED
<br />GFI-TYPE DUPLEX RECEPTACLE
<br />WP DENOTES WEATHERPROOF COVER
<br />�' -''
<br />WIRE IN CONDUIT CONCEALED BELOW SLAB
<br />SPECIAL PURPOSE RECEPTACLE
<br />OR GRADE
<br />®
<br />CEILING MOUNTED DUPLEX RECEPTACLE
<br />EMPTY CONDUIT
<br />TELE/DATA (BOX AND RACEWAY ONLY)
<br />FLEXIBLE CONDUIT
<br />OJ
<br />JUNCTION BOX
<br />CONDUIT TURNING UP
<br />TELE OUTLET (BOX AND RACEWAY ONLY)
<br />I-QTV
<br />TV OUTLET (RACEWAY ONLY)
<br />CONDUIT TURNING DOWN
<br />(EX)
<br />EXISTING TO REMAIN
<br />-1
<br />CONDUIT STUB
<br />(LION)
<br />UNLESS OTHERWISE NOTED
<br />3/4" PLYWOOD TELEPHONE BACKBOARD
<br />ALL SYMBOLS SHOWN MAY NOT BE USED.
<br />EXISTING PANEL A FLUSH MOUNTED, NEMA 1
<br />120016 VOLT, 3 PHASE, 4 WIRE FIRM VERIFY AXC RATING, MATCH NEW DEVICES
<br />225A MLO VIA20DA MAIN CKT SKR PROVIDii WITH EQUIPMENT GROUND BAR
<br />CKT
<br />OESCRIPTION
<br />SREAICER
<br />VOLT
<br />KVA
<br />LOAD
<br />CKT
<br />DESCRIPTION
<br />SPEAKER
<br />VOLT
<br />KVA
<br />LOAD
<br />TRIP
<br />I POLE1
<br />TRIP
<br />POLE
<br />1
<br />EXISTING AHU NORTH
<br />100
<br />a
<br />20a
<br />10.5
<br />a
<br />2
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.1
<br />1
<br />3
<br />2A
<br />4
<br />4
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />0.0
<br />1
<br />6
<br />a
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.6
<br />1
<br />7
<br />EXISTING EMIRGFJNCY LIGHTS
<br />20
<br />1
<br />120
<br />0.8
<br />1
<br />a
<br />EXBTMIG LIGHTS
<br />20
<br />1
<br />120
<br />0.7
<br />1
<br />a
<br />E EST" SMOKE DETIECTORS
<br />20
<br />1
<br />In
<br />0.a
<br />7
<br />10
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.1
<br />1
<br />1,
<br />EXIST" LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />12
<br />EXISTING LIGHTS
<br />2D
<br />1
<br />120
<br />1.1
<br />1
<br />18
<br />OWING ROOF WPAGFI R1ECEPTCLE
<br />20
<br />1
<br />120
<br />0.2
<br />8
<br />14
<br />EXISTING RECEPTACLES
<br />20
<br />1
<br />120
<br />0.7
<br />5
<br />to
<br />EXISTING RECEPTACLES
<br />20
<br />1
<br />170
<br />1.1
<br />a
<br />Is
<br />EXISTING FRONT SIGN
<br />20
<br />1
<br />120
<br />0.7
<br />1
<br />17
<br />EXISTING CIRCUT
<br />20
<br />1
<br />120
<br />1.0
<br />a
<br />1s
<br />EXCISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />1E
<br />OWING CIRCUT
<br />20
<br />1
<br />130
<br />1.0
<br />a
<br />20
<br />EXISTING CIROLJT
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />21
<br />EXISTING RECEPTACLES
<br />20
<br />1
<br />120
<br />1.0
<br />a
<br />29
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />as
<br />EXSTING LIGHTS
<br />20
<br />1
<br />120
<br />0.0
<br />1
<br />24
<br />OWING LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />M
<br />EXIST" LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />2S
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />0.9
<br />1
<br />27
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />20
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />0.9
<br />1
<br />20
<br />MUTING L*FITS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />30
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />0.9
<br />1
<br />31
<br />EXISTING LIGHTS
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />82
<br />DEDICATED CO'UNM OUTLET (3)
<br />20
<br />1
<br />120
<br />0.8
<br />7
<br />33
<br />FRONT RECEPTACLES (8)
<br />20
<br />1
<br />120
<br />ILA
<br />5
<br />34
<br />DEDICATED COUNTER OURET (3)
<br />20
<br />1
<br />120
<br />0.8
<br />7
<br />sa
<br />SAOK RECL9rTA4CLES (3)
<br />20
<br />1
<br />120
<br />4A
<br />a
<br />38
<br />DEDICATED COUNTER OUTLET (3)
<br />20
<br />1
<br />120
<br />0.6
<br />7
<br />37
<br />OFFICE RECEPTACLES (3)
<br />20
<br />1
<br />120
<br />0.2
<br />a
<br />38
<br />ISFRIGERATOR (3)
<br />20
<br />1
<br />120
<br />0.0
<br />7
<br />M
<br />OFFICE RECEPTACLES (3)
<br />20
<br />1
<br />120
<br />a 2
<br />a
<br />40
<br />RANGE M
<br />s0
<br />2
<br />2M
<br />6.0
<br />7
<br />41
<br />OFFICE RECEPTACLES M
<br />20
<br />1
<br />120
<br />0.2
<br />a
<br />1 42
<br />---
<br />SCOPE OF WORK
<br />1. ADD NEW LIGHT FIXTURES PER FLOOR PLAN - LIGHTING. PROVIDE LIGHTING CONTROLS AS
<br />INDICATED ON DRAWINGS. REFER TO ELECTRICAL SPECIFICATIONS, LIGHTING FIXTURE SCHEDULE,
<br />LIGHTING NOTES, AND DETAILS IF APPLICABLE TO THIS PROJECT.
<br />2. ADD NEW POWER AND SYSTEMS DEVICES PER FLOOR PLAN - POWER AND SYSTEMS. REFER TO
<br />ELECTRICAL SPECIFICATIONS, POWER AND SYSTEMS NOTES, PANEL SCHEDULES, AND POWER
<br />RISER DIAGRAMS IF APPLICABLE M THIS PROJECT.
<br />CODES AND STANDARDS
<br />FLORIDA BUILDING CODE, 6TH EDITION (2017)
<br />THE FLORIDA FIRE PREVENTION CODE 2010 EDITION
<br />NFPA 101: FLORIDA EDITION 2010
<br />NFPA 70: NATIONAL ELECTRICAL CODE 2011
<br />WMINSPAWLI FLUSH 1
<br />IZD= VOLT, a PHASE. 4 WIRE FIELD VERIFY Ale RATING, MATCH NEW DEVICES
<br />a26A1 MLO VIA 200A MAIN CNT GM PROVIDE WITH EQUIPMENT GROUND BAR
<br />CICT
<br />DESCRIPTION
<br />BREAKER
<br />VOLT
<br />KvA.cow
<br />LOAD
<br />CKT
<br />DESORPTION
<br />BREAKER
<br />VOLT
<br />KVA
<br />LOAD
<br />CO
<br />TRIP
<br />POLE
<br />TRIP
<br />POLE
<br />1
<br />EXSTINO AHU MOUTH
<br />100
<br />3
<br />208
<br />10.6
<br />2
<br />2
<br />NG WATER HEATER (FIELD VERIFY30
<br />2
<br />4.5
<br />7
<br />3
<br />2A
<br />4
<br />4
<br />--�
<br />a
<br />a
<br />EXISTING LIGHTS
<br />ENQ
<br />20
<br />1
<br />120
<br />1.0
<br />1
<br />7
<br />EXISTING LIGHTS
<br />2D
<br />1
<br />120
<br />0.8
<br />1
<br />8EXISTING
<br />RECEPTACLES
<br />20
<br />1
<br />120
<br />0 7
<br />a
<br />a
<br />EXISTING ROOF WPIGFI RE�TCLE
<br />20
<br />1
<br />IN
<br />0.2
<br />5
<br />10
<br />WATER HEATER (FIELD VERIFV
<br />20
<br />1
<br />120
<br />1.5
<br />7
<br />11
<br />EXOSTSNG FRONT awl
<br />2D
<br />1
<br />120
<br />1.2
<br />1
<br />12
<br />EXIS I NO DRINK FOUNTAIN
<br />20
<br />1
<br />12D
<br />0.7
<br />7
<br />13
<br />EXISTING FRONT SIGN
<br />M
<br />1
<br />120
<br />1.2
<br />1
<br />14
<br />EXISTING GROUT
<br />20
<br />1
<br />120
<br />0.7
<br />a
<br />1a
<br />EXISTING GROUT
<br />24
<br />1
<br />IN
<br />0.S
<br />a
<br />1a
<br />EXISTING GROUT
<br />2D
<br />1
<br />120
<br />0.7
<br />a
<br />17
<br />EXISTING CIRCUT
<br />20
<br />1
<br />in
<br />0.9
<br />a
<br />18
<br />rxanNO CRCUT
<br />20
<br />1
<br />IN
<br />1.0
<br />a
<br />12
<br />EXISTING CIRCUT
<br />20
<br />1
<br />10
<br />0.0
<br />a
<br />0
<br />EXISTING GROUT
<br />20
<br />1
<br />IN
<br />1.0
<br />a
<br />21
<br />EXISTING CIRCUT
<br />20
<br />1
<br />120
<br />0.1
<br />a
<br />22
<br />EXISTING GROUT
<br />20
<br />1
<br />IN
<br />1.0
<br />a
<br />23
<br />EXISTING CIRCUT
<br />20
<br />1
<br />IN
<br />0.0
<br />a
<br />24
<br />EXISTING GROUT
<br />20
<br />1
<br />IN
<br />1.0
<br />a
<br />as
<br />EXISTING CIRCUT
<br />20
<br />1
<br />In
<br />0.9
<br />a
<br />2a
<br />l70STING GROUT
<br />20
<br />1
<br />IN
<br />0.7
<br />a
<br />27
<br />EXISTING GROUT
<br />20
<br />1
<br />12D
<br />0.9
<br />a
<br />26
<br />EXISTING GROUT
<br />20
<br />1
<br />IN
<br />1.1
<br />a
<br />a
<br />EXISTING OIROUT
<br />20
<br />1
<br />1N
<br />0.0
<br />a
<br />so
<br />EXISTING GROUT
<br />20
<br />1
<br />120
<br />1.1
<br />a
<br />31
<br />EXISTING CIRCUT
<br />20
<br />1
<br />120
<br />0.0
<br />5
<br />32
<br />EXISTING GROUT
<br />2D
<br />I
<br />12D
<br />IA
<br />a
<br />M
<br />OUTWGALARM
<br />20
<br />1
<br />In
<br />0.6
<br />7
<br />34
<br />SPACE
<br />1
<br />36
<br />DRINC FOUNTAIN (3)
<br />N
<br />1
<br />120
<br />ILI
<br />7
<br />38
<br />SPACE
<br />1
<br />37
<br />SPACE
<br />1
<br />36
<br />SPACE
<br />1
<br />30
<br />SPACE
<br />1
<br />40
<br />SPACE
<br />1
<br />41
<br />SPACE
<br />1
<br />42
<br />SPAN
<br />1
<br />LOAD CODES
<br />CONNECTS
<br />DEMAND
<br />DEMAND LOAD
<br />LOAD CODES
<br />CONNECTED
<br />DEMAND
<br />DEMAND LCAO
<br />LOM (KVA)
<br />FACTOR
<br />LOAD (KVA)
<br />FACTOR
<br />1. LIGHTING
<br />20
<br />1.20
<br />26.4
<br />1. LIGHTING
<br />4
<br />1.26
<br />a.0
<br />2. HEAT
<br />11
<br />1.00
<br />10.5
<br />2. HEAT
<br />I 1
<br />1.00
<br />10.5
<br />3. AN COMN11ONING
<br />0
<br />1.00
<br />0.0
<br />3. AR CONDITIONING
<br />0
<br />I.W
<br />0.0
<br />4. MOTORS
<br />a
<br />26% LRGST MTR
<br />3.0
<br />4. MOTO"
<br />2
<br />26% LRUT MTR
<br />s.D
<br />a. RECWTACLES
<br />8
<br />NEC 21C.44
<br />8.4
<br />a. REcEPTAICM
<br />18
<br />NEO= 44
<br />142
<br />S. MISC. CONTINUOUS LOADS
<br />0
<br />1.6
<br />0.0
<br />8. MIS . CONTINUOUS LOADS
<br />0
<br />1.1E
<br />0.0
<br />7. MSC. NONCONTUJOUG ROADS
<br />12
<br />1.00
<br />11.8
<br />7. MISC. NON -CONTINUOUS LOADS
<br />6
<br />1.00
<br />80
<br />61 a7.,
<br />3.0 LESS SMALLEST OF HEAT/AC
<br />NOTES
<br />(1) ALL OMIT WALSLIS AND LOADS ARE OEM Ma UNLSN OTHERWISE NtXM $4.1 TOTAL DEMAND LOAD
<br />P) INNIT!N8 CIRWIT aREANNIL L411aTM16 LOAD MACX= DURMIB DEMOLITION (FXLD VIM M.
<br />ii) NEW ORWIT IREAItSI AND LOAD. VOLTAGE 208
<br />,
<br />PHASE 3
<br />150 AMPS
<br />43
<br />N=
<br />(1) ALL CKIJIT IRiAI M AND LOADS ARE OWN11 UNLESS OTHERWM NCTI M
<br />(2) EXI41M CIRCUI T IREAERI. WTIM LOAD Rl ADM DURR10 DEMOLITION (N®.0 VERIPIX.
<br />(3) NEW CIRCUIT SRLM= AND LOAD.
<br />40.7
<br />&0 LESS SMALLEST OF MEATAC
<br />.f"
<br />27.7 TOTAL DEMAND LOAD
<br />VOLTAGE US
<br />PHASE 3
<br />105 AMPS
<br />L.
<br />a)
<br />N
<br />a�
<br />ov
<br />a� s
<br />(n U
<br />o�p
<br />Lam+
<br />O
<br />Go
<br />a
<br />r-1
<br />°O
<br />i
<br />V
<br />a
<br />C
<br />sq
<br />N
<br />�M
<br />cp
<br />Tom,
<br />TEQ
<br />Cq
<br />IN
<br />U
<br />ice4
<br />Ld
<br />O
<br />U
<br />cD
<br />z
<br />0
<br />m
<br />� z
<br />� o
<br />3 0
<br />z
<br />CL 3
<br />o a
<br />U g
<br />Ln Lr)
<br />a
<br />W O
<br />�_: M
<br />0
<br />LLT
<br />cn
<br />o z
<br />J o
<br />o w
<br />Y (n
<br />0 0
<br />w pLLJ
<br />L
<br />0
<br />>~
<br />ad
<br />V
<br />4�
<br />0
<br />Cc)
<br />.�
<br />0
<br />0
<br />E-4
<br />70
<br />go
<br />>G•r
<br />�
<br />Dy
<br />>~(
<br />0
<br />r
<br />m
<br />(L
<br />e-I
<br />A,
<br />ELECTRICAL NOTES
<br />Scale: As Noted
<br />Revisions:
<br />Date:
<br />12-29-17
<br />Drawn by.
<br />CTK
<br />Checked by.
<br />CTK
<br />E � 2
<br />Sheet No. of
<br />
|