|
PLUMBING GENERAL NOTES
<br />1. ALL WORK UNDER THIS DIVISION SHALL COMPLY WITH THE CODES AND STANDARDS AS LISTED ON THE PROJECT DRAWINGS AND TO OTHER PERTINENT CODES MADE A PART OF SUCH
<br />CODE BY REFERENCE.
<br />2. PLANS INDICATE THE SCHEMATIC LAYOUT AND LOCATION OF THE PLUMBING SYSTEM COMPONENTS. UNLESS SPECIFIC DIMENSIONS ARE NOTED, THE ACTUAL LOCATION OF THESE
<br />COMPONENTS SHALL BE DETERMINED IN THE FIELD IN COORDINATION WITH THE WORK OF OTHER TRADES, THE USE OF MANUFACTURER'S SHOP DRAWINGS AND SIMILAR CERTIFIED DATA.
<br />PLANS SHALL NOT BE SCALED.
<br />3. NO EXCLUSIONS FROM OR LIMITATIONS IN THE LANGUAGE USED IN THE CONTRACT DOCUMENTS SHALL BE INTERPRETED AS MEANING THAT EQUIPMENT,
<br />APPURTENANCES, AND/OR ACCESSORIES NECESSARY FOR A COMPLETE AND OPERATIONAL SYSTEM ARE NOT TO BE PROVIDED AS REQUIRED. THE SEPARATE DIVISIONAL DRAWINGS AND
<br />SPECIFICATIONS DO NOT RELIEVE THE CONTRACTOR FROM THE RESPONSIBILITY TO PROVIDE THE WORK WHICH IS INDICATED ON ANY OF THE DRAWINGS OR DIVISION OF THE
<br />SPECIFICATIONS. REVIEW AND COORDINATE THE SCOPE OF WORK WITH ALL SECTIONS TO ASSURE A COMPLETE AND FUNCTIONAL SYSTEM IS INSTALLED.
<br />4. SUBMIT SHOP DRAWINGS OF ALL FIXTURE, EQUIPMENT, AND MATERIALS FOR REVIEW. INSTALL AND TEST ALL EQUIPMENT AND MATERIALS IN ACCORDANCE WITH THE
<br />MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. FOR ALL EQUIPMENT, WHICH HAS BEEN SCHEDULED DIRECTLY ON THE DRAWINGS, PROVIDE WITHIN THE SUBMITTAL, A
<br />PERFORMANCE SCHEDULE FOR THE PROPOSED EQUIPMENT IN THE SAME FORMAT AS INCLUDED ON THE CONTRACT DOCUMENT. FAILURE TO PROVIDE REQUIRED PERFORMANCE SCHEDULE
<br />WILL RESULT IN REJECTION OF THE ENTIRE SUBMITTAL. BIND SHOP DRAWINGS/CATALOG-CUTS IN THREE RING BINDERS WITH A TITLE SHEET AND IDENTIFICATION ON FRONT AND SIDE OF
<br />THE BINDER. SUBMIT DRAWINGS AND CUT SHEETS FOR ALL PRODUCTS ALL AT ONE TIME. INDEX ALL ITEMS TO THE PROJECT MANUAL OR DRAWINGS AS APPLICABLE. SHOP DRAWINGS
<br />THAT DEVIATE FROM THE REQUIREMENTS OF THE CONTRACT DOCUMENTS SHALL LIST ALL DIFFERENCES IN A COVER LETTER ATTACHED TO TOP OF THE SUBMITTAL. ANY UNLISTED
<br />DEVIATIONS FOUND DURING REVIEW WILL RESULT IN THE REJECTION OF THE ENTIRE SUBMITTAL.
<br />5. PIPING AND OTHER ITEMS OF THE PLUMBING SYSTEM SHALL BE SUPPORTED DIRECTLY FROM THE BUILDING STRUCTURE AND NOT FROM THE CEILING, CEILING SUSPENSION SYSTEM,
<br />DUCTWORK OR ELECTRICAL SYSTEMS.
<br />6. ALL PIPING MUST BE INSTALLED 6" AWAY FROM ANY FIRE RATED WALL.
<br />7. FOR SEALING OF PIPE PENETRATIONS THRU FIRE RATED WALLS REFER TO ARCHITECTURAL DRAWINGS AND SPECIFICATIONS. ALL PIPE PENETRATIONS SHALL BE SEALED USING APPROVED
<br />UL DETAILS.
<br />8. PROVIDE ADDITIONAL PIPING SUPPORTS ON BOTH SIDES AND WITHIN 18" OF FIRE RATED WALLS. PIPING SHALL NOT BE SUPPORTED FROM ANY RATED WALL. SLEEVE AND/OR FIRESTOP
<br />ALL PENETRATIONS THROUGH RATED WALL, CEILINGS, AND FLOOR WITH UL LISTED ASSEMBLIES. FIRESTOP ASSEMBLIES SHALL BE EQUAL TO OR EXCEED THE RATING OF THE WALL,
<br />CEILING, OR FLOOR. SEE ARCHITECTURAL DRAWINGS FOR FINAL FINISHES.
<br />9. HANGERS, ANCHORS AND SUPPORTS SHALL SUPPORT THE PIPING AND THE CONTENTS OF THE PIPING. HANGERS AND STRAPING MATERIALS SHALL BE OF APPROVED MATERIALS THAT
<br />WILL NOT PROMOTE GALVANIC ACTION.
<br />10. HANGERS AND ANCHORS SHALL BE ATTACHED TO THE BUILDING CONSTRUCTION IN AN APPROVED MANNER.
<br />11. ANCHORAGE SHALL BE PROVIDED TO RESTRAIN DRAINAGE PIPING FROM AXIAL MOVEMENT. FOR PIPE SIZES GREATER THAN 4", RESTRAINTS SHALL BE PROVIDED FOR DRAIN PIPES AT ALL
<br />CHANGES IN DIRECTION AND AT ALL CHANGES IN DIAMETER GREATER THAN TWO PIPE SIZES. BRACES, BLOCKS, RODDING AND OTHER SUITABLE METHODS AS SPECIFIED BY THE COUPLING
<br />MANUFACTURER SHALL BE UTILIZED.
<br />12. ALL EQUIPMENT (WATER HEATERS, ETC) SHALL BE LABELED WITH PLASTIC SIGNS, LAMINATED, ENGRAVED: 1/8" THICK BLANKS FOR SIGNS SHALL BE A MINIMUM OF 1-3/4" HIGH, WITH 1"
<br />HIGH LETTERS. LENGTH OF THE SIGN SHALL BE THE SUM OF THE LETTERS/NUMBERS PLUS 3/4" EACH END.
<br />13. PROVIDE ALL OFFSETS AND FITTINGS REQUIRED FOR A FULLY FUNCTIONAL SYSTEM. MAKE CONNECTION TO SITE UTILITIES. COORDINATE WITH SITE UTILITY CONTRACTOR AS REQUIRED.
<br />14. CONCEAL PIPING ABOVE CEILING, WITHIN WALL OR CHASES OR AS SPECIFICALLY NOTED.
<br />15. PROVIDE ACCESS PANELS (EQUAL TO MIFAB PRODUCTS) FOR ALL VALVES CONCEALED IN WALLS OR ABOVE NON -ACCESSIBLE CEILINGS.
<br />16. PROVIDE A 1/2" ROUND RED DOT ON THE CEILING GRID BELOW ALL VALVES.
<br />17. ALL EXPOSED PIPE AND FITTINGS IN FINISHED AREAS SHALL BE CHROME PLATED. IF PIPING IS NOT AVAILABLE CHROME PLATED, PIPING SHALL BE PAINTED WITH CHROME COLORED
<br />PAINT.
<br />18. PROVIDE CLEANOUTS IN ACCORDANCE WITH THE FLORIDA PLUMBING CODE, 6th EDITION (2017). INSTALL CLEANOUT WITH COVER FLUSH TO FINISH SURFACE. WHEN OUTDOORS, PROVIDE
<br />CONCRETE ADJACENT TO CLEANOUT.
<br />19. COORDINATE PIPING WITH ALL ELECTRICAL EQUIPMENT (PANELS, TRANSFORMERS, ETC.) PRIOR TO ANY INSTALLATION. DO NOT ROUTE ANY PIPING OVER ANY ELECTRICAL PANELS.
<br />20. ALL WALL MOUNTED LAVATORIES SHALL BE ATTACHED TO FLOOR MOUNTED CARRIERS DESIGNED TO WITHSTAND A VERTICAL LOAD OF 250 POUNDS ON THE FRONT OF FIXTURE.
<br />21. PROVIDE SANITARY WASTE, VENT, DOMESTIC WATER, ETC. ROUGH -IN AND MAKE FINAL CONNECTIONS (TO INCLUDE PROVIDING ALL NECESSARY RELATED STOPS, VALVES, TRAPS, ETC. AND
<br />MAKE READY TO USE) TO ALL EQUIPMENT, WHETHER FURNISHED BY THIS CONTRACTOR OR FURNISHED BY OTHERS.
<br />22. SECURE THE BASE OF ALL WATER COOLERS TO THE WALL. CAULK ALONG TOP OF WATER COOLER TO WALL.
<br />23. FOLLOW ADA GUIDELINES FOR ACCESSIBILITY TO PLACES OF PUBLIC ACCOMMODATION AND COMMERCIAL FACILITIES BY INDIVIDUALS WITH DISABILITIES. THESE GUIDELINES ARE TO BE
<br />APPLIED DURING DESIGN, CONSTRUCTION AND ALTERATION OF SUCH BUILDING AND FACILITIES TO THE EXTENT REQUIRED BY REGULATIONS ISSUED BY FEDERAL AGENCIES, INCLUDING THE
<br />DEPARTMENT OF JUSTICE, UNDER THE AMERICANS WITH DISABILITIES ACT (ADA) OF JANUARY 1997 AND THE REQUIREMENTS OF ANSI A117.1.
<br />24. PRIOR TO ANY EXCAVATION OR DEMOLITION, THE CONTRACTOR SHALL COORDINATE HIS WORK WITH OTHER TRADES.
<br />25. REFER TO ARCHITECTURAL DRAWINGS FOR EXACT LOCATION AND ROUGHING DIMENSIONS OF ALL PLUMBING FIXTURES, DRAINS, FAUCETS, SHOWER HEADS, ETC.
<br />26. ALL FLOOR DRAINS SHALL BE SERVED BY AN APPROVED TRAP PRIMER, EXCEPTION: SHOWER DRAINS.
<br />27. PROVIDE 1 /2" TYPE K SOFT COPPER SUPPLY LINE FROM TRAP PRIMER TO FLOOR DRAIN PROVIDE CORROSION PROTECTION BELOW SLAB.
<br />28. ALL HOSE BIBBS, WALL HYDRANTS AND HOSE END CONNECTIONS SHALL BE EQUIPPED WITH AN APPROVED INTEGRAL VACUUM BREAKER AND SHUT OFF VALVE LOCATED ABOVE THE
<br />CEILING. UNLESS OTHERWISE NOTED, ALL WALL HYDRANTS AND HOSE BIBBS SHALL BE INSTALLED 24" ABOVE FINISHED FLOOR OR GRADE.
<br />29. DIELECTRIC UNIONS SHALL BE INSTALLED AT ALL CONNECTIONS OF DISSIMILAR METALS (SUCH AS COPPER TO GALVANIZED STEEL).
<br />30. ALL VENT PENETRATIONS THROUGH THE ROOF SHALL BE LOCATED A MINIMUM OF 10'-0"
<br />FROM ALL FRESH AIR INTAKES, DOORS, WINDOWS AND OTHER BUILDING OPENINGS. WHERE
<br />POSSIBLE, EXTEND VENT PIPE TO THE BACK SIDE OF BUILDINGS WITH SLOPED ROOFS.
<br />31. BELOW GRADE SOIL, WASTE AND VENT PIPING SHALL BE PVC TYPE DWV AND SHALL CONFORM TO ONE OF THE FOLLOWING STANDARDS: ASTM D 2665, ASTM D 2949 OR CSA B181.2.
<br />FITTINGS SHALL BE PVC AND SHALL CONFORM TO ONE OF THE FOLLOWING STANDARDS: ASTM D 2665, ASTM D 3311 OR ASTM F 1866. JOINTS SHALL BE SOLVENT CEMENTING. A PURPLE
<br />PRIMER THAT CONFORMS TO ASTM F 656 SHALL BE APPLIED TO JOINT SURFACES (CLEAN AND FREE FROM MOISTURE). SOLVENT CEMENT NOT PURPLE IN COLOR AND CONFORMING TO
<br />ASTM D 2564, CSA B137.3, CSA B181.2 OR CSA B182.1 SHALL BE APPLIED TO ALL JOINT SURFACES.
<br />JOINTS SHALL BE IN ACCORDANCE WITH ASTM D 2855.
<br />32. ABOVE GRADE SOIL, WASTE AND VENT PIPING SHALL BE SERVICE WEIGHT HUBLESS CAST-IRON PIPE AND FITTINGS WITH WIDE BODY TYPE 304 STAINLESS STEEL HEAVY-DUTY COUPLINGS
<br />WITH NEOPRENE GASKETS. PIPE SHALL CONFORM TO ASTM A 74, CISPI 301, OR ASTM A 888. COUPLINGS SHALL CONFORM TO CISPI 310 OR ASTM C 1277. THE ELASTOMERIC SEALING
<br />SLEEVE SHALL CONFORM TO ASTM C 564 OR CAN/CSA B602 AND SHALL BE PROVIDED WITH A CENTER STOP.
<br />33. HOT AND COLD WATER PIPING SHALL BE SEAMLESS TYPE "L" HARD COPPER TUBE AND SHALL CONFORM TO NSF 61 AND ONE OF THE FOLLOWING STANDARDS, ASTM B 75, ASTM B 88,
<br />ASTM B 251 OR ASTM B 447. FITTINGS SHALL BE COPPER OR COPPER ALLOY AND SHALL CONFORM TO NSF 61 AND ONE OF THE FOLLOWING STANDARDS ASME B16.15, ASME B16.18,
<br />ASME B16.22, ASME 816.23, ASME B16.26 OR ASME B16.29. SOLDERED JOINTS SHALL BE MADE IN ACCORDANCE WITH THE METHODS OF ASTM B828. THE JOINING OF WATER SUPPLY
<br />SHALL BE 95/5 LEAD FREE SOLDER AND THE SOLDER SHALL CONFORM TO ASTM B 32.
<br />34. THE CONTRACTOR SHALL FURNISH AND INSTALL VALVES WHERE INDICATED ON PLAN AND NECESSARY FOR PROPER SYSTEM OPERATION AND COMPONENT ISOLATION. PROVIDE VALVES
<br />RATED FOR 125 PSI OR GREATER WORKING PRESSURE IN WATER PIPING.
<br />BALL VALVES: NIBCO S-585-70
<br />GATE VALVES: NIBCO S-113
<br />CHECK VALVES: NIBCO S-413
<br />BALANCING VALVE: NIBCO S-1710
<br />35. INSULATE ALL DOMESTIC HOT WATER PIPING WITH 1" THICK FIBERGLASS WITH "ASJ" VAPOR BARRIER JACKET AND 25/50 FIRE/SMOKE RATING.
<br />36. VERIFY SIZES, LOCATION, INVERTS AND ELEVATIONS PRIOR TO INSTALLING ANY PIPING.
<br />37. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALL PLUMBING EQUIPMENT WITH THE ELECTRICAL DRAWINGS AND SHALL FURNISH EQUIPMENT
<br />WIRED FOR THE VOLTAGE SHOWN HEREIN. PROVIDE STATEMENT INDICATING THIS HAS OCCURRED WITH THE SHOP DRAWING SUBMITTALS.
<br />38. SLOPE ALL SANITARY PIPING 3" TO 6" AT A MINIMUM SLOPE OF 1/4" PER FOOT. ALL SANITARY PIPING 2-)2" AND SMALLER SHALL BE SLOPED AT A MINIMUM OF 1/4" PER FOOT.
<br />39. ALL EXPOSED PIPING UNDER ACCESSIBLE LAVATORIES SHALL BE INSULATED WITH PROTECTIVE UNDER -SINK PIPE COVERS AND PLUMBING ENCLOSURES FROM TRUEBRO.
<br />40. ALL SANITARY, VENT AND WATER PIPING SHALL BE TESTED BEFORE BEING CONCEALED IN ANY WAY. ALL JOINTS SHALL BE MADE DRIP TIGHT BEFORE BEING CONCEALED. DOMESTIC
<br />WATER PIPING SHALL BE TESTED AT 1-1/2 TIMES OPERATING PRESSURE OR 100 PSI, WHICHEVER IS GREATER.
<br />41. PLUMBING CONTRACTOR SHALL DISINFECT POTABLE WATER SYSTEM PER THE FLORIDA BUILDING CODE, 6th EDITION (2017). PROVIDE DOCUMENTATION IN THE CLOSE OUT DOCUMENTS.
<br />PLUMBING FIXTURES
<br />MINIMUM CONNECTIONS
<br />FIXTURE
<br />TRIM
<br />SEAT
<br />DRAIN
<br />TRAP
<br />SUPPLY
<br />CARRIER
<br />INSULATION
<br />WASTE VENT CW HW
<br />WATER CLOSET/ADA
<br />SOLID PLASTIC,
<br />INTEGRAL
<br />CAST BRASS,
<br />WHITE, VITREOUS CHINA, ELONGATED
<br />OPEN FRONT,
<br />LOOSE KEY HANDLE,
<br />WC-1
<br />4pp
<br />2
<br />1 /2
<br />-
<br />BOWL, 1.28 GPF, 2-1 /8 GLAZED
<br />LESS COVER,
<br />CHROME PLATED.
<br />--
<br />--
<br />TRAPWAY, PRESSURE ASSISTED, FLOOR
<br />WHITE.
<br />MOUNTED.
<br />MCGUIRE 2166LK
<br />BEMIS 1655SSCT
<br />KOHLER "CIMARRON" K-3609
<br />LAVATORY/ADA
<br />CHROME FINISH, CAST
<br />CAST BRASS
<br />CHROME PLATED
<br />CHROME PLATED,
<br />ADJUSTABLE SUPPORT
<br />WHITE, FLEXIBLE
<br />WHITE, ENAMELED CAST IRON, WALL
<br />BRASS, 4" CENTERSET,
<br />CHROME PLATED
<br />CAST BRASS BODY
<br />LOOSE KEY HANDLE,
<br />SYSTEM, STEEL
<br />VINYL, MOLDED,
<br />S-1
<br />1-1/2"
<br />1-1/2"
<br />1 /2"
<br />1 /2"
<br />HUNG, 19" X 17", 4" CENTERS, WITH
<br />BLADE TYPE HANDLE,
<br />--
<br />OFFSET WHEELCHAIR
<br />WITH CLEANOUT
<br />TWO REQUIRED.
<br />UPRIGHTS.
<br />PROTECT DRAIN,
<br />OVERFLOW, FOR CONCEALED ARM
<br />VANDAL RESISTANT
<br />STRAINER, 1-1/4"
<br />PLUG, 1-1/4" X
<br />TRAP AND SUPPLIES.
<br />CARRIER.
<br />OUTLET, 0.5 GPM.
<br />OFFSET TAILPIECE.
<br />1-1/2".
<br />MCGUIRE 2165CCLK
<br />JAR R SMITH SERIES
<br />700 AS REQUIRED
<br />TRUEBRO
<br />KOHLER "HUDSON" K-2861
<br />SYMMONS S-60-H
<br />MCGUIRE 155A
<br />MCGUIRE 8902
<br />"LAV-SHIELD"
<br />MODEL #2018-KO-H
<br />SINK
<br />CHROME FINISH,
<br />STAINLESS STEEL
<br />CHROME PLATED
<br />1 /2" NOMINAL X
<br />STAINLESS STEEL, TYPE 304, 18 GAUGE,
<br />METAL CONSTRUCTION,
<br />STRAINER BODY,
<br />CAST BRASS BODY
<br />3/8" O.D. ANGLE
<br />S-2
<br />1-1/2"
<br />1-1/2"
<br />1 /2"
<br />1 /2"
<br />UNDERMOUNT, SINGLE BASIN, OVERALL
<br />SINGLE LEVER HANDLE,
<br />--
<br />1-1 /2"x4"
<br />WITH CLEANOUT
<br />SUPPLY, LOOSE KEY
<br />--
<br />--
<br />18-1 /2% 18-1 /2% 5-1/2" DEEP, FULLY
<br />QUARTER TURN
<br />CHROME PLATED
<br />PLUG, 1-1/2" X
<br />STOP, WALL FLANGE,
<br />UNDERCOATED, 3-1/2" CENTER REAR
<br />CERAMIC CONTROL
<br />BRASS TAILPIECE,
<br />1-1/2".
<br />CHROME PLATED.
<br />LOCATION DRAIN OPENING.
<br />COMPONENTS,
<br />FITS 3-1/2" DRAIN
<br />GOOSENECK SPOUT,
<br />OPENINGS.
<br />MCGUIRE 8912
<br />MCGUIRE 2165CCLK
<br />ELKAY "LUSTERTONE" ELUHAD1616
<br />1.5 GPM.
<br />ELKAY LK99
<br />SYMMONS DIA
<br />SPB-3510-1.5
<br />ELECTRIC WATER COOLER/ADA
<br />CHROME PLATED
<br />CHROME PLATED,
<br />ADJUSTABLE SUPPORT
<br />SELF CONTAINED, BI-LEVEL, WALL HUNG,
<br />CAST BRASS BODY
<br />SOLID BRASS,
<br />SYSTEM, STEEL
<br />EWC-1
<br />1-1 /2"
<br />1-1 /2"
<br />1 /2"
<br />-
<br />ELECTRIC REFRIGERATED, BARRIER FREE
<br />--
<br />--
<br />--
<br />WITH CLEANOUT
<br />LOOSE KEY HANDLE,
<br />UPRIGHTS, 3"X4"
<br />--
<br />ACCESS, SELF CLOSING EASY TOUCH
<br />PLUG, 1-1/4" X
<br />ONE REQUIRED.
<br />BASE PLATE.
<br />CONROL. CERTIFIED TO NSF/ANSI 61.
<br />1-1/2".
<br />ZURN Z8804LKQ-PC
<br />JAY R SMITH 0830
<br />ELKAY LZSTL8C
<br />MCGUIRE 8902
<br />ELECTRIC WATER HEATER
<br />ON SHELF IN FOOD SERVICE ROOM
<br />EWH-1
<br />3/4"
<br />-
<br />RHEEM MODEL XE20SO6ST38U0
<br />--
<br />--
<br />--
<br />--
<br />--
<br />--
<br />--
<br />20 GAL.
<br />MOP BASIN
<br />POLISHED CHROME,
<br />WHITE, MOLDED STONE, 24"x24"x10"
<br />VACUUM BREAKER,
<br />3" PVC P-TRAP
<br />MB-1
<br />3"
<br />2"
<br />3/4"
<br />3/4"
<br />HIGH, STAINLESS STEEL DRAIN BODY,
<br />3/4" HOSE END,
<br />COMBINATION DOME STRAINER AND
<br />INTEGRAL STOPS,
<br />STAINLESS STEEL LINT BASKET, 3"
<br />ADJUSTABLE SUPPLY
<br />CONNECTION, HOSE AND WALL HOOK
<br />ARMS.
<br />832 AA, MOP HANGER 889 CC,
<br />STAINLESS STEEL WALL GUARDS.
<br />CHICAGO 897
<br />FIAT MSB-2424
<br />ABBREVIATIONS
<br />SYMBOL DESCRIPTION
<br />BFF
<br />BELOW FINISH FLOOR
<br />BFP
<br />BACKFLOW PREVENTOR
<br />CFH
<br />CUBIC FEET PER HOUR
<br />CO
<br />CLEANOUT
<br />CW
<br />DOMESTIC COLD WATER
<br />DFU
<br />DRAINAGE FIXTURE UNIT
<br />'F
<br />DEGREE FAHRENHEIT
<br />FD
<br />FLOOR DRAIN
<br />GPH
<br />GALLONS PER HOUR
<br />GPM
<br />GALLONS PER MINUTE
<br />HB
<br />HOSE BIBB
<br />HW
<br />DOMESTIC HOT WATER
<br />HWR
<br />DOMESTIC HOT WATER RETURN
<br />IE
<br />INVERT ELEVATION
<br />KW
<br />KILOWATT
<br />PSI
<br />POUNDS PER SQUARE INCH
<br />PVC
<br />POLYVINYL CHLORIDE PIPE
<br />SAN
<br />SANITARY
<br />SFU
<br />SUPPLY FIXTURE UNIT
<br />TPV
<br />TEMP/PRESSURE RELIEF VALVE
<br />UN
<br />UNION
<br />VTR
<br />VENT THRU ROOF
<br />WH
<br />WALL HYDRANT
<br />PLUMBING LEGEND & SYMBOLS
<br />SANITARY SOIL & WASTE
<br />SAN
<br />SANITARY SOIL & WASTE (BELOW GRADE)
<br />SAN
<br />SANITARY VENT
<br />V
<br />DOMESTIC COLD WATER
<br />CW
<br />DOMESTIC HOT WATER (110')
<br />HW
<br />DOMESTIC HOT WATER (120')
<br />HW
<br />120
<br />DOMESTIC HOT WATER RETURN
<br />HWR
<br />PIPE DROP
<br />D,
<br />PIPE RISE
<br />0-
<br />PIPE CONNECTION (TOP)
<br />n
<br />PIPE CONNECTION (BOTTOM)
<br />SHUT-OFF VALVE (VERTICAL RISER)
<br />I C
<br />SHUT-OFF VALVE (IN CAST IRON BOX)
<br />HOSE BIBB / WALL HYDRANT
<br />C
<br />WALL CLEANOUT
<br />FLOOR DRAIN
<br />SHUTOFF VALVE
<br />-v
<br />GATE VALVE„
<br />-
<br />CHECK VALVE (SWING)
<br />UNION
<br />(
<br />BALANCING VALVE (CALIBRATED)
<br />.01
<br />STRAINER
<br />WATER HAMMER ARRESTOR
<br />�- OR
<br />TEMP/PRESS RELIEF VALVE (ASME)
<br />a�
<br />ti,
<br />H
<br />a�
<br />o
<br />`v
<br />fn
<br />U
<br />c-+
<br />a
<br />M
<br />�
<br />>F
<br />V
<br />V
<br />a
<br />C
<br />in1
<br />C6
<br />go
<br />w �
<br />�
<br />w
<br />C N
<br />ui
<br />Cm
<br />0
<br />U
<br />C�
<br />z
<br />0
<br />J
<br />m
<br />Q
<br />2
<br />o'
<br />o w
<br />z
<br />= o
<br />a �
<br />o a-
<br />C-.,) g
<br />U d>
<br />U
<br />r4D CC)
<br />O 6)
<br />E4
<br />b
<br />100 ' DO
<br />N
<br />L-1
<br />PLUMBING NOTES
<br />Scale: As Noted
<br />Revisions:
<br />Date:
<br />12-29-17
<br />Drawn by.
<br />CTK
<br />Checked by.
<br />CTK
<br />1) �2
<br />Sheet No. of
<br />
|