Laserfiche WebLink
1"=10' <br />1 1 30 n 3� 21 10 0 20 40 80 n_ 1 90 v ' %q _ 46 _ _i _ O 40 80 r 11_ 150 n_ <br />1 =20 1 -30 1 =40 1 -50 11001 <br />1al.1 300 <br />PROJECT NAME <br />MEDICAL BUILDING <br />MODIFICATIONS <br />HW HW HW <br />HOT WATER <br />- - - - - - - - <br />COLD WATER <br />PLUMBING PLAN <br />HOT & COLD WATER <br />SCALE: 1 /4" = 1.-0 <br />P1-2 <br />GENERAL NOTES: <br />THESE DRAWINGS HAS BEEN CREATED FROM <br />PREVIOUS CONTRACT DOCUMENTS, WHILE <br />ACTUAL CONDITIONS HAVE BEEN INVESTIGATED <br />TO THE BEST OF THE DESIGNER ABILITY, THE <br />CONTRACTOR SHALL FIELD VERIFY THE EXISTING <br />CONDITIONS DURING THE COURSE OF WORK <br />AND COORDINATE ANY DISCREPANCIES WITH <br />THE ARCHITECT/DESIGNER/ENGINEER <br />1. ALL WORK SHALL COMPLY WITH APPLICABLE NATIONAL, STATE AND LOCAL CODES. <br />THIS SHALL INCLUDE, BUT NOT BE LIMITED TO THE STANDARD PLUMBING CODE. <br />2. THE PLUMBING SUBCONTRACTOR SHALL VISIT THE JOB SITE AND VERIFY THE <br />EXISTING PLUMBING, COMPARE IT TO THE DESIGN BEFORE PURCHASE, FABRICATION AND <br />INSTALLATION OF ANY FIXTURE, PIPE, EQUIPMENT, ETC.. <br />3. THE PLUMBING SUBCONTRACTOR SHALL INSTALL AND MAKE ALL PLUMBING <br />CONNECTIONS TO OWNER FURNISHED EQUIPMENT. <br />4. REVIEW PLANS OF ALL TRADES PRIOR TO BIDING AND INSTALLATION TO INCLUDE <br />ALL PLUMBING FOR SYSTEMS SHOWN ON THE PLANS AND AS REQUIRED. <br />5. VERIFY LOCATION OF EXISTING WATER SERVICE AND THE LOCATION/INVERTS OF <br />SANITARY PIPING PRIOR TO INSTALLATION. <br />6. VERIFY MOUNTING HEIGHT AND WATER CONNECTION SIZES TO ALL PLUMBING <br />FIXTURES PRIOR TO ROUGH -IN. <br />7. COORDINATE WITH OTHER TRADES TO PREVENT INTERFERENCE WITH HVAC DUCTS, <br />STRUCTURE, ELECTRICAL LIGHTING, AND OTHER PIPING IN THE CEILING SPACE. VENT <br />PIPING AND WATER PIPING SHALL BE HELD EITHER ABOVE OR BELOW EXISTING HVAC <br />DUCTWORK <br />8. ALL WORK, BOTH MATERIAL AND INSTALLATION SHALL BE GUARANTEED FOR A <br />PERIOD OF ONE YEAR FROM ACCEPTANCE BY THE OWNER. <br />9. ALL CHANGES SHALL BE APPROVED BY THE ARCHITECT. <br />10. COORDINATE WITH THE ARCHITECTURAL DRAWINGS BEFORE ROUGHING -IN <br />PLUMBING FIXTURES AND EQUIPMENT SUPPLIES. <br />11. MAKE PROPER HOT AND COLD WATER, WASTE AND VENT PIPING CONNECTIONS TO <br />ALL FIXTURES AND EQUIPMENT EVEN THOUGH ALL FITTINGS AND CONNECTIONS ARE <br />NOT SHOWN. <br />12. ALL HOT PIPING INDICATED TO BE RUN ABOVE FINISHED CEILINGS OR IN EXTERIOR <br />WALLS SHALL BE INSULATED ON THE CONDITIONED SPACE SIDE OF THE BUILDING <br />INSULATION. <br />13. FURNISH AND INSTALL ALL REQUIRED COMPONENTS INCLUDING TRAPS TAILPIECES, <br />AND SUPPORTS. PROVIDE FLOOR DRAINS WITH TRAP PRIMER CONNECTED TO COLD <br />WATER SUPPLY. <br />14. ELKAY, DAYTON, KOHLER AND DELTA MAY BE SUBMITTED FOR APPROVAL BY THE <br />DESIGNER. ALL SUBMITTED MATERIALS MUST COMPLETELY DESCRIBE THE ITEM <br />INVOLVED. THIS WILL BE SUBJECT TO ENGINEERS REVIEW. <br />15. INSULATION FOR ALL POTABLE HOT WATER PIPING TO BE IN ACCORDANCE WITH <br />THE FLORIDA ENERGY CODE, LATEST EDITION. <br />16. ALL PLUMBING FIXTURES TO COMPLY WITH TABLE 604.4 THE MAXIMUM FLOW RATES <br />AND CONSUMPTION FOR PLUMBING FIXTURES AND FIXTURE SYSTEM. <br />17. WHERE SERVICES ARE REQUIRED TO BE REMOVED, RELOCATED OR ABANDONED, <br />BY-PASS UTILITY SERVICES, SUCH AS PIPE OR CONDUIT, BEFORE CUTTING, CUT-OFF <br />PIPE OR CONDUIT IN WALLS OR PARTITIONS TO BE REMOVED, CAP, VALVE, OR PLUG <br />AND SEAL THE REMAINING PORTION OF PIPE OR CONDUIT TO PREVENT ENTRANCE OF <br />MOISTURE OR OTHER FOREIGN MATTER AFTER BY-PASSING OR CUTTING. <br />TEMPERED WATER SHALL BE PROVIDED THROUGHT AN APPROVED WATER -TEMPERATURE <br />LIMITING DEVICE (85'-110' F) THAT CONFORMS TO ASSE 1070 AND/OR CSA B125.3 <br />OWNER: <br />ADAA REAL ESTATE LLC <br />2653 BRUCE B DOWNS BLVD. <br />WESLEY CHAPEL , FL 33544 <br />PROJECT ADDRESS <br />38058 ARBOR RIDGE DRIVE. <br />ZEPHYRHILLS, FL 33540 <br />DRAWING BY: <br />DANIEL JALIL <br />Associate AIA <br />M.A. In Architecture & Planning <br />10233 CELTIC ASH DR. <br />Ruskin, FL 33753 <br />Phone (813) 240-3537 <br />THIS DRAWING MEASURING 24"x36" IS THE PROPERTY OF DANIEL <br />JALIL AND MAY NOT BE USED OR REPRODUCED WITHOUT HIS <br />WRITTEN PERMISSION.. <br />THIS DRAWING AND DESIGN IS VALID FOR 12 MONTHS AFTER THE <br />DATE IS SIGNED AND SEALED. <br />ENGINEER: <br />I HEREBY CERTIFY THAT I HAVE <br />REVIEWED THE ATTACHED DESIGN AND <br />FOUND IT TO BE IN COMPLIANCE WITH <br />THE 7TH EDITION OF THE FLORIDA <br />BUILDING CODE 2020. <br />DANIEL JAMES COOREY P.E. <br />FL 77065 <br />Phone (813) 507-9166 <br />DATE ISSUED FOR: <br />SHEET TITLE <br />HOT AND COLD WATER <br />PLAN <br />JOB No. ZPH-0821 <br />SCALE AS NOTED <br />DATE AUG-09-21 <br />DRAW BY DJ <br />CHECKED BY DJ <br />PLOT DATE 08-09-21 <br />DRAWING No <br />P1-2 <br />T=1'-0" 1 1 /2"=1'-011pm 3/4"=1'-011EM91 /4"=1'-011 1 /8"=1'-011 1 /16"=1'-0" <br />0 0 1 0 2 2 0 2 4 8 6 0 12 40 16 <br />