|
`x
<br />a
<br />-
<br />ABBREVIATIONS
<br />AC -AIR CONDITIONING ID -INSIDE DIAMETER / DIMENSION
<br />AFF -ABOVE FINISH FLOOR IN -INCH
<br />AHU -AIR HANDLER UNIT INCL -INCLUDED / INCLUDING
<br />ALT -ALTERNATE INFO-tNFORhAT1ON
<br />j ALUM -ALUMINUM INS/-1 -INSULATION
<br />APPROX -APPROXIMATE INT -INTERIOR
<br />ARCH -ARCHITECTURAL INV -INVERT
<br />ACT -ACOUSTICAL CEILING TILE
<br />AV -AUDIO VISUAL JAN -JANITOR
<br />AVG -AVERAGE JC -JANITOR'S CLOSET
<br />JST -JOIST
<br />BD -BOARD JT -JOINT
<br />BFE -BASE FLOOD ELEVATION
<br />BEJ -BRICK EXPANSION JOINT K -KIP (1000LB)
<br />BLDG -BUILDING KPL -KICK PLATE
<br />BLK -BLOCK KIT -KITCHEN
<br />BM -BEAM KO -KNOCKOUT
<br />BOT -BOTTOM
<br />BRG -BEARING LAB -LABORATORY
<br />BLK -BLOCK LB -POUND
<br />BRK -BRICK LDG -LANDING
<br />BSMT -BASEMENT LAM -LAMINATE, LAMINATION
<br />BUR -BUILT-UP ROOFING LAV -LAVATORY
<br />LB -POUND
<br />CAB -CABINET LF -LINEAR FOOT
<br />CAT -CATEGORY LGT -LIGHT
<br />CBU -CEMENTATIONS BACKER UNIT LKR -LOCKER
<br />CD -CONSTRUCTION DOCUMENTS LN -LINE
<br />CEMT-CEMENTITIOUS LVL -LAMINATED VENEER LUMBER
<br />CG -CORNER GUARD LGT -LIGHT
<br />CIP -CAST IN PLACE MAINT -MAINTENANCE
<br />CJ -CONTROL JOINT / CONSTRUCTION JOINT MATL -MATERIAL
<br />CL -CENTER LINE MAX -MAXIMUM
<br />CLG -CEILING MDF -MEDIUM DENSITY FIBERBOARD
<br />CLG HT -CEILING HEIGHT MDO -MEDIUM DENSITY OVERLAY PLYWOOD
<br />CLR -CLEAR MECH -MECHANICAL
<br />CMU -CONCRETE MASONRY UNIT MEP -MECHANICAL, ELECTRICAL, PLUMBING
<br />CNTR -COUNTER MEZZ -MEZZANINE
<br />CO-CLEANOUT MFR -MANUFACTURER
<br />COL -COLUMN MH -MANHOLE
<br />1 CONC -CONCRETE MIN -MINIMUM
<br />CONTT -CONSTRUCT OR CONSTRUCTION MISC-MISCELLANEOUS
<br />CONT -CONTINUOUS OR CONTINUES ML DG -MOULDING
<br />j CT -CERAMIC TILE 1 COOLING TOWER MM -MILLIMETER
<br />CTR ENTER MN. T -MOUNT OR MOUNTING
<br />CTSK COUNTERSUNK MO -MASONRY NING
<br />j CW -COLD WATER (PIPING) M-: T METAL
<br />MULL-iv1ULDON
<br />DBL -DOUBLE fb1UNT-MUNTIN
<br />DEG -DEGREE
<br />DEMO -DEMOLITION N -NORTH
<br />DEPT -DEPARTMENT NA -NOT APPLICABLE
<br />DET -DETAIL NC -NOISE CRITERIA
<br />DF -DRINKING FOUNTAIN NIC -NOT IN CONTRACT
<br />DIA -DIAMETER NO -NUMBER
<br />DIFF -DIFFUSER NOM-NOMINAL
<br />DIM DIMENSION NTS -NOT TO SCALE
<br />DISP -DISPENSER # -NUMBER
<br />DN -DOWN
<br />DO -DOOR OPENING OA -OUTSIDE AIR
<br />DR -DOOR OC -ON CENTER
<br />DRN -DRAIN OD -OUTSIDE DIAMETER/DIMENSION
<br />DS -DOWNSPOUT OFCI -OWNER FURNISHED, CONTR INSTALLED
<br />DW -DISHWASHER OF01 -OWNER FURNISHED, OWNER INSTALLED
<br />DWG -DRAWING OFF -OFFICE
<br />DWR -DRAWER OPNG -OPENING
<br />OPP -OPPOSITE
<br />(E) -EXISTING OPT -OPTIONAL
<br />E -EAST ORD -OVERFLOW ROOF DRAIN
<br />EA -EACH OVHD -OVERHEAD
<br />EB -EXPANSION BOLT (EXPANSION ANCHOR)
<br />EIFS -EXTERIOR INSULATION AND FINISH SYSTEM P -PAINT
<br />EJ -EXPANSION JOINT PATD -PAPER TOWEL DISPENSER
<br />EL -ELEVATION PB -PUSH BUTTON
<br />ELEC -ELECTRICAL PBD -PARTICLEBOARD
<br />ELEV -ELEVATOR PC -PRECAST CONCRETE
<br />EMERG -EMERGENCY PDF -POWDER DRIVEN FASTENER
<br />ENCL -ENCLOSURE PED -PEDESTAL
<br />EP -ELECTRICAL PANEL BOARD PERF -PERFORATED
<br />EQ -EQUAL PERIM -PERIMETER
<br />EQUP -EQUIPMENT PERP -PERPENDICULAR
<br />EWC -ELECTRICAL WATER COOLER, PLANT -PLASTIC LAMINAT E
<br />EXH -EXHAUST PLA.S -PLASTER
<br />EXP JT -EXPANSION JOINT PLBG -PLUMBING
<br />EXIST -EXISTING PLF -POUNDS PER LINEAR FOOT
<br />EXT -EXTERIOR PLT -PLATE
<br />PLYaWD -PLYWOOD
<br />FP, -FIRE ALARM PKT -POCKET
<br />FB -FACE BRICK PNI_ -PANEL
<br />FC -FACE PR -PAIR
<br />FD -FLOOR DRAIN PREFAB -PREFABRICATED
<br />FDC -FIRE DEPARTMENT CONNECTION PROJ -PROJECT
<br />FND -FOUNDATION PSF -FOUNDS PER SQUARE FOOT
<br />FE -FIRE EXTINGUISHER PSI -POUNDS PER SQUARE INCH
<br />FEC -FIRE EXTINGUISHER CABINET PT -PRESSURE TREATED
<br />FF&E -FURNITURE, FINISHES & EQUIPMENT PTD -PAINTED
<br />FFEL -FINISH FLOOR ELEVATION PTN -PARTITION
<br />FG -FIXED GLASS PTR -PAPER TOWEL RECEPTACLE
<br />FHC -FIRE HOSE CABINET
<br />FIN -FINISH QT -QUARRY TILE
<br />FIN FLR -FINISHED FLOOR QTY-QUANITITY
<br />FLR -FLOOR
<br />FO -FACE OF (R) -RELOCATED
<br />FP -FIRE PROTECTION RA -RETURN AIR
<br />FPG -FIREPROOFING RAID -RADIUS
<br />FIR -FRAME RB -RESILIENT BASE
<br />FT -FEET RCP -REFLECTED CEILING PLAN
<br />FRTW -FIRE RETARDANT TREATED WOOD RD -ROOF DRAIN
<br />FTG -FOOTING RECPT -RECEPTACLE
<br />FURN -FURNITURE REC -RECESS
<br />FURR -FURRING REF -REFERENCE
<br />FWC -FABRIC WALL COVERING REFR -REFRIGERATOR
<br />FWP -FABRIC WRAPPED PANEL REINF -REINFORCING
<br />REL -RELOCATE
<br />GA -GAUGE REM -REMOVABLE
<br />GALV -GALVANIZED REQD -REQUIRED
<br />GB -GRAB BAR RESIL -RESILIENT
<br />GC -GENERAL CONTRACT(OR) REV -REVISION / REVISED
<br />GFCI -GROUND FAULT CIRCUIT INTERRUPTOR RM -ROOM
<br />GRC -GLASS FIBER REINFORCED CONCRETE RO -ROUGH OPENING
<br />GRG -GLASS FIBER REINFORCED GYPSUM R T D -RATED
<br />GL -GLASS RWL -RAIN WATER LEADER
<br />GR -GRADE
<br />GRID -GROUND S -SOUTH
<br />GWB -GYPSUM WALL BOARD SA -SUPPLY AIR
<br />SAN -SANITARY
<br />HB -HOSE BIB SC -SOLID CORE
<br />HC -HOLLOW CORE SCHED -SCHEDULE
<br />HCP -HANDICAPPED SCP -SCUPPER
<br />HD -HEAD SCRh! -SCREEN
<br />HDW -HARDWARE SECT -SECTION
<br />HDWD -HARDWOOD SF -SQUARE FEETiFOOT
<br />HM -HOLLOW METAL (STEEL FRAME) SHLVS -SHELVES
<br />HNDRL -HANDRAIL SHT -SHEET
<br />HO -HOLD-OPEN SHWR -SHOWER
<br />HORIZ -HORIZONTAL SGD -SLIDING GLASS DOOR
<br />HRC -HOSE REEL CABINET SIM -SIMILAR
<br />HR -HOUR SND -SANITARY NAPKIN DISPENSER
<br />HS -HEAT STRENGTHENED (GLASS) SP -STANDPIPE
<br />HSS -HOLLOW STRUCTURAL SECTION SPEC -SPECIFICATIONS
<br />j HT -HEIGHT SPR-SPRINKLER
<br />HVAC -HEATING, VENTILATING, AIR CONDITIONING SPKR -SPEAKER
<br />HW -HOT WATER SO -SQUARE
<br />SO IN
<br />-SQUARE INCH
<br />SS
<br />-STAINLESS STEEL
<br />STD
<br />-STANDARD
<br />STL
<br />-STEEL
<br />STOR
<br />-STORAGE
<br />STRUCT
<br />-STRUCTURAL
<br />SUSP
<br />-SUSPENDED
<br />SYM
<br />-SYMMETRICAL
<br />T&G
<br />-TONGUE AND GROOVE
<br />TB
<br />-TOWEL BAR
<br />TEL
<br />-TELEPHONE
<br />TEMP
<br />-TEMPERED
<br />THK
<br />-THICK OR THICKNESS
<br />THRU
<br />-THROUGH
<br />TMPD
<br />-TEMPERED
<br />TOC
<br />-TOP OF CONCRETE
<br />TOS
<br />-TOP OF SLAB 1 TOP OF STRUCTURE
<br />TOSTL
<br />-TOP OF STEEL
<br />TOM
<br />-TOP OF MASONARY
<br />TPD
<br />-TOILET PAPER DISPENSER
<br />TV
<br />-TELEVISION
<br />TYP
<br />-TYPICAL
<br />UNO
<br />-UNLESS NOTED OTHERWISE
<br />UR
<br />-URINAL
<br />VCT
<br />-VINYL COMPOSITION TILE
<br />VERT
<br />-VERTICAL
<br />VIF
<br />-VERIFY IN FIELD
<br />VT
<br />-VINYL TILE
<br />VTR
<br />-VENT THROUGH ROOF
<br />VWC
<br />-VINYL WALL COVERING
<br />W/
<br />-WITH
<br />WC
<br />-WATER CLOSET
<br />WD
<br />-WOOD
<br />WDW
<br />-WINDOW
<br />WH
<br />-WATER HEATER
<br />WL
<br />-WIND LOAD
<br />1A110
<br />-WITHOUT
<br />WP
<br />-WATERPROOF
<br />WPM
<br />-WATERPROOF MEMBRANE
<br />WT
<br />-WEIGHT
<br />W1N'M
<br />-WELDED WIRE MESH
<br />DRAWING NAMING CONVENTION
<br />PREFIX REFERENCE:
<br />• CS = COVER SHEET
<br />• G = GENERAL INFORMATION
<br />• LS = LIFE SAFETY
<br />• AD = ARCHITECTURAL DEMOLITION
<br />• A = ARCHITECTURAL
<br />• PA = PRODUCT APPROVAL INFORMATION
<br />SUFFIX REFERENCE:
<br />• ALPHA SUFFIX (DRAWING TYPE - VARIATION)
<br />• (NO SUFFIX) = NOTES
<br />• .D = DIMENSIONS
<br />• R = REFLECTED CEILING PLAN
<br />• NUMERIC SUFFIX (CONTINUATION ON MULTIPLE SHEETS)
<br />• .1
<br />• .2
<br />• ETC.
<br />NUMBER REFERENCE:
<br />• 000's - GENERAL INFORMATION
<br />• 001's - SITE PLANS
<br />• 100's - PLANS
<br />• 100 = PLAN NOTES (WHERE APPLICABLE)
<br />• 101's = PLANS (THIRD DIGIT IS FLOOR LEVEL)
<br />• 200's - ELEVATIONS
<br />• 200 = GENERAL EXTERIOR ELEVATION NOTES
<br />• 201's = EXTERIOR ELEVATIONS
<br />• 250 = INTERIOR ELEVATIONS
<br />• 250 = GENERAL INTERIOR ELEVATION NOTES
<br />• 251'S = INTERIOR ELEVATIONS
<br />• 300's - SECTIONS
<br />• 300 = SECTION NOTES
<br />• 301's = OVERALL BUILDING SECTIONS
<br />• 350's = EXTERIOR WALL SECTIONS
<br />• 350 = EXTERIOR WALL SECTION NOTES
<br />• 351's = EXTERIOR WALL SECTIONS
<br />• 400's - ENLARGED PLANS
<br />• 400 = ENLARGED PLAN NOTES
<br />• 401's = ENLARGED PLANS
<br />• 450's = VERTICAL CIRCULATION
<br />• 450 = VERTICAL CIRCULATION NOTES
<br />• 451's = ENLARGED PLANS -SECTIONS -DETAILS
<br />• 500's - ENLARGED DETAILS
<br />• 500 = ENLARGED DETAIL NOTES
<br />• 501's = ENLARGED DETAILS (NOT COVERED IN OTHER SECTIONS)
<br />• 600's - DOOR AND WINDOW SCHEDULES AND DETAILS
<br />• 600 = DOOR AND WINDOW NOTES AND ELEVATIONS
<br />• 601's = DOOR AND WINDOW SCHEDULES
<br />• 650 = ENLARGED DOOR AND WINDOW NOTES
<br />• 651's = ENLARGED DOOR AND WINDOW DETAILS
<br />• 700's - RESTROOMS-KITCHENS
<br />• 700 = RESTROOM - KITCHEN NOTES
<br />• 701's = ENLARGED PLANS -ELEVATIONS -SECTIONS -DETAILS -
<br />(MILLWORK REFERENCED TO 750's)
<br />• 750'S = MILLWORK
<br />• 750 = MILLWORK NOTES
<br />• 751'S = MILLWORK PLANS - ELEVATIONS - SECTIONS - DETAILS
<br />• 800'S - FINISHES
<br />• 800 = FINISHES - MATERIALS - STANDARDS - NOTES
<br />• 801's = FINISH PLANS - DETAILS
<br />• 850'S = FURNITURE
<br />• 850 = FURNITURE NOTES
<br />• 851's = FURNITURE PLANS
<br />• 900'S - 3D VIEWS
<br />GENERAL DRAWING SYMBOLS
<br />i
<br />i
<br />DRAWING REFERENCE SYMBOL
<br />REFER TO THIS VIEW
<br />i IDENTIFICATION NUMBER
<br />1 REFER TO THIS
<br />�01 SHEET NUMBER
<br />CATEGORY
<br />DISCIPLINE
<br />PREFIX
<br />EXTERIOR ELEVATIONS
<br />��- INDICATES DIRECTION OF ELEVATION VIEW
<br />1 REFER TO THIS VIEW IDENTIFICATION NUMBER
<br />A2 1 REFER TO THIS SHEET NUMBER
<br />CATEGORY
<br />DISCIPLINE PREFIX
<br />INTERIOR ELEVATIONS
<br />1I,-- REFER TO THIS VIEW IDENTIFICATION NUMBER
<br />INDICATES DIRECTION OF ELEVATION VIEW
<br />4 <A201 2 REFER TO THIS SHEET NUMBER
<br />3
<br />COLUMN GRID T
<br />EFERENCE
<br />I \
<br />COLUMN GRID NUMBER -
<br />/ HORIZONTAL GRID LINES
<br />A
<br />COLUMN GRID LINES
<br />�i COLUMN GRID LETTER -
<br />VERTICAL GRID LINES
<br />VIEW TITLE BAR
<br />VIEW NUMBER
<br />TITLE E-'-"- VIEW TITLE
<br />1
<br />VIEW SCALE
<br />BUILDING 1 WALL SECTION REFERENCE
<br />�- INDICATES DIRECTION OF SECTION VIEW
<br />REFER TO THIS VIEW IDENTIFICATION NUMBER
<br />� 1
<br />A201 REFER TO THIS SHEET NUMBER
<br />CATEGORY
<br />DISCIPLINE PREFIX
<br />DETAIL REFERENCE
<br />REFER TO THIS VIEW IDENTIFICATION NUMBER
<br />REFER TO THIS SHEET NUMBER
<br />40 CATEGORY
<br />DISCIPLINE PREFIX
<br />------
<br />i i
<br />CALL OUT BOX
<br />i
<br />`-----------'
<br />ELEVATION LEVEL REFERENCE
<br />GRAPHIC SYMBOLS
<br />N
<br />�X,
<br />TRUE NORTH
<br />TAGS
<br />� STOREFRONT TAG
<br />�� J DOOR TAG
<br />GENERAL NOTES
<br />i
<br />i
<br />1. THE CONTRACTOR SHALL PROVIDE COMPLETE PROJECT SYSTEMS AND COMPONENTS AND COMPLY WITH ALL REQUIREMENTS INDICATED IN THE PROJECT
<br />DOCUMENTS.
<br />2. THE CONTRACTOR SHALL BE RESPONSIBLE FOR FOLLOWING ALL LOCAL, STATE, AND FEDERAL SAFETY PROGRAMS AND REGULATiONS.
<br />3. THE CONTRACTOR SHALL BE RESPONSIBLE FOR MEANS AND METHODS, TECHNIQUES OF CONSTRUCTION AND CONSTRUCTiON' SEQUENCING 10 COMPLY WITH
<br />ALL OF THE REQUIREMENTS INDICATED IN THE PROJECT DOCUMENTS.
<br />4. THE CONTRACTOR SHALL CONSTRUCT THE BUILDING IN FULL COMPLIANCE WITH ALL APPLICABLE CODES AND BUILDING REGULATiONS AS WELL'
<br />THEDRAWINGS AND SPECIFICATIONS. IF A CONFLICT BETWEEN SUCH REQUIREMENTS OCCURS. THE MOST STRINGENT REQUIREMENT(S) k LL GOVERN.
<br />5. ANY CODE DEFECIENCIES IN THE DRAWINGS RECOGNIZED BY THE CONTRACTOR SHOULD BE BROUGHT TO THE ATTENTION OF THE ARCHITECT FOR
<br />CLARIFICATION BEFORE BIDDING AND COMMENCEMENT OF WORK.
<br />6. IT SHALL BE THE GENERAL CONTRACTOR'S RESPONSIBILITY TO FIELD INSPECT THE PROJECT SITE PRIOR TO THE SUBMITTAL OF HIS BID. THE CONTRACTOR
<br />SHALL BE FULLY AWARE OF THE EXISTING CONDITIONS AND THEIR INTERFACE WITH THE NEW CONSTRUCTION.
<br />7. UNLESS OTHERWISE SPECIFIED, THE CONTRACTOR SHALL FURNISH A WRITTEN GUARANTEE FOR ALL WORK (EQUIPMENT, MATERIALS, AND LABOR), AGAINST
<br />ANY DEFECTS IN SAID WORK FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF SUBSTANTIAL COMPLETION, WITH ALL ,APPROPRIATE REPAIRS OR
<br />REPLACEMENTS AT NO ADDITIONAL COST TO THE OWNER,
<br />8. GENERAL CONTRACTOR IS RESPONSIBLE TO FIELD VERIFY AND DOCUMENT ALL EXISTING FIELD CONDITIONS. ANY DEVIATIONS FROM THE EXISTING CO1.10iTiGt";
<br />DRAWINGS WILL BE ADDRESSED IMMEDIATELY WITH THE ARCHITECT.
<br />9. PRIOR TO COMMENCING ANY WORK THE GENERAL CONTRACTOR IS RESPONSIBLE TO VERIFY THE LOCATION OF ALL UTILITY POINTS OF CONNECTION AND
<br />INCLUDE ALL ASSOCIATED WORK SUCH AS REPAIR / REPLACEMENT OF FINISHES WHERE NECCESSARY.
<br />10. ALL TRADES TO BE COORDINATED WITH EACH OTHER AND FULLY INFORMED AND AWARE OF THE WORK OF OTHERS.
<br />11. THE CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATION OF ALL WORK CONCERNING PROVISIONS FOR AND INSTALLATION OF EQUIPMENT AS NOTED,
<br />12. THE CONTRACTOR SHALL VERIFY ALL EXISTING UTILITIES SUCH AS SANITARY, SEWER, WATER, NATURAL GAS AND ELECTRICAL LOCATIONS.
<br />13. PLUMBING, ELECTRICAL, AND HVAC SUBCONTRACTORS SHALL BE CITY AND STATE LICENSED AS REQUIRED.
<br />14. THE CONTRACTOR SHALL, UPON DISCOVERY, GIVE WRITTEN NOTICE TO THE ARCHITECT OF ANY MATERIALS, EQUIPMENT OR DESIGN FEATURES VVHICH HE
<br />BELIEVES TO BE INADEQUATE OR UNSUITABLE, IN VIOLATION OF LAWS, ORDINANCES, OR RULES AND OF ANY NECESSARY ITEMS OR WORK OMITTED FR`M THE
<br />DRAWINGS.
<br />15. ALL WORK SHOWN ON THE DRAWINGS IS TO BE CONSTRUCTED OF NEW, DEFECT FREE COMPONENTS ONLY, UNLESS SPECIFIED OTHERWWISE,
<br />16. THE INFORMATION ON THE DRAWINGS IS AS EXACT AS COULD BE SECURED. ABSOLUTE ACCURACY IS NOT GUARANTEED. AND THE CONTRACTOR SHALL.
<br />OBTAIN EXACT LOCATIONS, MEASUREMENTS, LEVELS, ETC. AND SHALL SATISFACTORILY ADAPT HIS WORK TO THE ACTUAL CONDITIONS. DO NOT SCALE
<br />PRINTS. VERIFY ALL QUESTIONABLE DIMENSIONS WITH THE ARCHITECT PRIOR TO COMMENCING WORK.
<br />17. ITEMS NOTED AS "BY OWNER OR GC" ARE TO BE COORDINATED WITH OWNER AND PURCHASED AND INSTALLED BY CONTRACTOR,
<br />18, CONTRACTOR SHALL BE RESPONSIBLE TO INSTALL ALL ITEMS, MATERIALS & ASSEMBLIES IN ACCORDANCE WITH THE MANUFACTURERS SPECIFICATIONS AND
<br />INSTALLATION GUIDELINES. IF ANY QUESTIONS, DISCREPANCIES OR INCONSISTENCIES ARISE THAT CONFLICT WITH THE DEJiCN DOCUN'ENTS, COONTRACTOR
<br />SHALL NOTIFY THE ARCHITECT IN WRITING IMMEDIATELY.
<br />19, CONTRACTOR SHALL MAINTAIN AN OPERABLE AND READILY AVAILABLE 5L6 ABC FIRE EXTINGUISHER AND SMOKE DETECTORS DUFtiNC DEn'OLi i t A''1
<br />CONSTRUCTION,
<br />20. ALL SMOKE AND FIRE RATED WALLS WILL BE LABELED ABOVE THE CEILING FINISH WITH RED, PAINTtiD STEieCiL=D LETTERING 1DrENTIFViNG THE MALL RATiNr
<br />AND STATING "PROTECT ALL PENETRATIONS." STENCILED LABELING WILL OCCUR ON BOTH SIDES OF EACH SMOKE AND FIRE RATED WALL AT N T MCU; E THAN
<br />20 FEET ON CENTER AND ALL WALL TERMINATIONS OR CHANGES IN DIRECTION WILL BE DESIGNATED WITH A VERTICAL LINE.
<br />21. ALL EXISTING MECHANICAL, ELECTRICAL, PLUMBING AND FIRE PROTECTION SYSTEMS NEEDED TO MAINTAIN CONTIN000S O'ERA 'ONS OF THE PACII!, Y. WiI.L
<br />BE CAPPED OFF OR REROUTED AS NECESSARY.
<br />22. GENERAL CONTRACTOR WILL SCHEDULE ALL WORK TO AVOID INTERRUPTIONS TO ADJACENT AREA_. ALL D'sSRI)F'TIVE :^/ORK'WI!.L BE SCHEDULED :INC
<br />PERFORMED BEFORE OR AFTER NORMAL BUSINESS HOUR. WORK STOPPAGE DUE TO VIBRATIONS, OR THAT DISTURB THE OCCUPANT OF THE FACILI 1 r WILL
<br />NOT BE GROUNDS FOR ADDITIONAL CHARGES OR CHANGE ORDERS.
<br />23. CONTRACTOR WILL USE ONLY THOSE ENTRANCES AND PARKING FACILITIES ASSIGNED BY THE BUILDING OWNER FOR SITE ACCESS. ALL MATERIAL DELIVERIES
<br />WILL BE SCHEDULED TO MINIMIZE DISRUPTIONS TO THE BUILDING OCCUPANTS.
<br />24. ALL BUILDING SYSTEM SERVICES (IE: WATER, SANITARY, FIRE ALARM, ELECTRIC, ETC...) WILL REMAIN IN OPER.AIGN THROLiGHOU7 CONiSTRUC i iON. ALL
<br />NECESSARY INTERRUPTIONS FOR CONNECTION OF NEW WORK WILL BE PERFORMED AFTER NORMAL BUSINESS i k-_,LJ,RS, OR AS ACUREED i 0 r Y C1.:IL['1NC
<br />OWNER. ANY REQUIRED INTERRUPTIONS OF SERVICE WILL BE SCHEDULED AND APPROVED BY THE BUILDING OWNER 72 HOURS IN ADVANCE. ALL- CCiS
<br />IMPACTS FOR AFTER HOURS WORK WILL BE ANTICIPATED AND INCLUDED IN BID PROPOSAL.
<br />25. ALL SUBCONTRACTORS SHALL USE SKILLED CRAFTSMEN EXPERIENCED IN THE WORK OF THEIR TRADE. ANY WORK NOT EQUAL TO BEST TRADE STANDAPDS
<br />SHALL BE REMOVED AND REPLACED AT NO ADDITIONAL COST. SHOULD ANY SUBCONTRACTOR REFUSE TO REMOVE AND REPLACE UNSATISFACTORY WORK,
<br />THE CONTRACTOR MAY REMOVE AND REPLACE IT, AND CHARGE THE COST TO THE SUBCONTRACTOR.
<br />26. ALL PRODUCTS AND PARTS SHALL FIT TOGETHER NEATLY, WITHOUT DAMAGE OR DISFIGUREMENT, EXCEPT FOR SPECIFIED CURVED SURFACES, ALL PRODUCTS
<br />AND PARTS SHALL BE CONSTRUCTED/ FABRICATED AND INSTALLED TRUE, IN LINE, AND PLUMB.
<br />27. IF SCOPE OF WORK REQUIRES THE REMOVAL OF FIXTURES OR DEVICES, ALL ASSOCIATED WIRE, BOXES, FRAMING AND PIPING NECESSARY TO ALLOW THE
<br />COMPLETE INSTALLATION OF NEW FINISHES WILL BE REMOVED .ALSO.
<br />28. MAINTAIN AREAS FREE OF WASTE MATERIALS. DEBRIS, AND RUBBISH ON A DAILY BASIS, MAINTA N THE SITE IN A CLEAN AND ORDERLY CONDITION. REMOVE
<br />DEBRIS AND RUBBISH FROM PIPE CHASES, PLENUMS, ATTICS, CRAWL SPACES AND OTHER CLOSED OR REIMOTE SPACES. PRIOR TO ENCLOSING THE SPACE
<br />BROOM AND VACUUM CLEAN INTERIOR AREAS PRIOR TO START OF SURFACE FINISHING, AND CONTINUE CLEANING TO ELIMiNATE D!;ST. REMOVE WASTE
<br />MATERIALS, DEBRIS, AND RUBBISH FROM SITE WEEKLY AND DISPOSE OFF -SITE.
<br />29. DETAILS ARE INTENDED TO SHOW THE INTENT OF THE DESIGN. MINOR MODIFICATIONS MAY BE REQUIRED TO SUIT THE FIELD DIMENSIONS OR CONDITIONS AND
<br />SUCH MODIFICATIONS SHALL BE INCLUDED AS PART OF THE WORK OF THE CONTRACT.
<br />30. CONTRACTOR SHALL PROVIDE SHOP DRAWINGS AND SUBMITTALS FOR ALL DISCIPLINES LISTED WITHIN THE CONSTRUCTION DOCUMENT SET. SHOP DRAWINGS
<br />AND / OR SUBMITTALS FOR PRODUCTS, MATERIALS, ASSEMBLIES, AND SYSTEMS SPECIFIED IN THE CONTRACT DOCUMENTS WILL BE SUBMITTED BY THE
<br />GENERAL CONTRACTOR TO THE ARCHITECT PRIOR TO FABRICATION IN ORDER TO VERIFY GENERAL CONFORMANCE WITH THE CONTRACT DOCUMENTS, SHIP
<br />DRAWINGS AND SUBMITTALS MUST BEAR A REVIEW STAMP FROM THE GENERAL CONTRACTOR PRIOR TO BEING SUBMITTED TO THE ARCHITECT.
<br />31. SHOP DRAWING REVIEW WILL NOT RELIEVE ANY PARTY FROM MAINTAINING COMPLIANCE WITH THE CONTRACT DOCUMENTS.
<br />32. IF "SHAFTS/CHASES/DEMISING WALLS" AND STRUCTURAL ELEMENTS ARE ACCIDENTALLY OPENED DURING CONSTRUCTION, CONTRACTOR SHALL NOTIFY THE
<br />ARCHITECT IMMEDIATELY.
<br />33. ALL WORK PERFORMED ON SITE SHALL NOT HINDER THE DAILY WORK PROCESS OF THE SITE. CONTRACTOR SHALL BARRICADE THE CONSTRUCTION AREAS
<br />FROM ANY NON -CONSTRUCTION PERSONNEL.
<br />34. ALL EXISTING BUILDING SYSTEMS, INCLUDING BUT NOT LIMITED TO, SHAFTS, EXTERIOR WINDOW SYSTEMS, CORRIDORS, PUBLIC SPACES, FIBER OPTIC
<br />SYSTEMS, MECHANICAL, PLUMBING, ELECTRICAL, ETC.. SHALL NOT BE ALTERED WITHOUT THE ARCHITECT AND OWNER'S APPROVAL.
<br />35. CONTRACTOR SHALL MAINTAIN AND PROTECT ALL EXISTING FIRE PENETRATIONS, INCLUDING BUT NOT LIMITED TO CHASE, S! ;AFT, AND DEWSING *WALL
<br />LOCATIONS (V.I.F.)
<br />36. SPRINKLER SYSTEM MODIFICATIONS WITHIN PREMISES AND SCHEDULED FREEZING ARE REQUIRED TO BE COORCINATED lWl i H BLIiL01,N IMANAGEVE'%'T FC0ry
<br />APPROVAL PRIOR TO WORK PERFORMED BY LICENSED SPRINKLER CONTRACTOR.
<br />37. CABINETRY, APPLIANCES, FIXTURES AND MILLWORK SHALL CONFORM TO ALL APPLICABLE CODES AND EQi_ilptv4F-Nd i LOCATIONS}
<br />ARE REQUIRED TO BE FINALIZED AND APPROVED BY ARCHITECT AND INTERIOR DESIGNER.
<br />38. CONTRACTOR SHALL BE RESPONSIBLE TO INSTALL ALL ITEMS, MATERIALS & ASSEMBLIES IN ACCORDANCE 1,''VIT y rH= t, AitiUF.ACTIiRE kS SPEICIFICATION-S AND
<br />INSTALLATION GUIDELINES. IF ANY QUESTIONS, DISCREPANCIES OR INCONSISTENCIES ARISE THAT CONF! ICT WITH THE DESIG:^d COCUPlEidT3. CONTRACTOR
<br />SHALL NOTIFY THE ARCHITECT IN WRITING iMMEDIATELY.
<br />39. ALL SUBCONTRACTORS SHALL COORDINATE ALL NEW AND RECONFIGURED LOCATIONS OF FIXTURES AND EQUIPMENT IWI ! H O NEE R'RICR TO INS G4:
<br />40. UPON COMPLETION OF WORK THE CONTRACTOR SHALL THOROUGHLY CLEAN THE PREMISES AND WASH THE INSIDE OF ALL kA'iNDOv iS SO T HAT THE SPACE is
<br />READY FOR OCCUPANCY BY THE OWNER. THIS INCLUDES BUT IS NOT LIMITED TO VACUUMING, SWEEPING, DUSTING AND REMOVING ALL TRASH AND DEBRIS
<br />LEFT FROM CONSTRUCTION.
<br />41. UPON COMPLETION OF THE WORK, THE CONTRACTOR SHALL FURNISH THE OWNER WITH A CERTIFIED STATEMENT TO THE EFFECT THAT ALL SALES AND USE
<br />TAXES DUE TO THE FEDERAL GOVERNMENT, STATE, COUNTY, AND,f OR MUNICIPALITY HAVE BEEN PAID.
<br />DEFINITIONS
<br />DEFINITIONS:
<br />1. 'TYPICAL" OR "TYP" INDICATES IDENTICAL COMPLETE SYSTEM SHALL BE PROVIDED FOR EACH OCCURRENCE: OF THE CONDI c1 ,N' NOTED,
<br />2. "SIMILAR" INDICATES COMPLETE SYSTEM AND COMPONENTS SHALL BE PROVIDED COMPARABLE 1*0 THE CHARACTERISTICS FOR THE CON01I-ION NOTED.
<br />3. "AS REQUIRED" INDICATES COMPONENTS REQUIRED TO COMPLETE THE NOTED, SYSTEM AS INDICATED IN THE PROJECT DOCUMENTS, SHALL BE PROVIDED.
<br />4. "ALIGN" INDICATES ACCURATELY PROVIDE FINISH FACES OF MATERIALS IN STRAIGHT, TRUE, AND PLUMB RELATION TO ADJACENT MATERIALS.
<br />DIMENSIONING
<br />A. DIMENSIONS INDICATED ARE TO:
<br />1. THE CENTERLINES OF THE STRUCTURAL GRID
<br />2. STEEL STRUCTURE: ON OR FROM STRUCTURAL GRID LINES
<br />3. FACE OF CONCRETE WALL
<br />4. OUTSIDE FACE OF CMU WALL
<br />5. INTERIOR FRAMED WALLS: PLAN EAST (OR PLAN NORTH) FROM FACE OF STUD - SEE PARTITION TYPES - VLRiFY ORIENTATION OF ASSYMET,r C ?'VA1 i
<br />TYPES
<br />6. EXTERIOR FRAMED WALLS: TO OUTSIDE FINISH FACE
<br />7. DOOR AND WINDOW OPENINGS:
<br />1. CMU WALLS: TO ROUGH OPENING
<br />2. INTERIOR FRAMED WALLS: ADJACENT TO SIDE WALL: 5" RETURN MEASURED FROM THE FiMSH FF.;,E OF ,' J?:CENT vVALL T 0 Ii T RiOR F4.CE OF
<br />DOORFRAME
<br />3. INTERIOR FRAMED WALLS: AWAY FROM SIDE WALLS: DIMENSIONED TO CENTER OF DOOR
<br />8. SPECIAL AND CODE REQUIRED CLEARANCES - AS INDICATED ON PLANS OR FINISH SURFACE TO FINISH SURFACE
<br />B. ALIGNMENT OF PARTITIONS AND FINISHES AS SCHEDULED SHALL BE STRAIGHT, TRUE AND PLUMB.
<br />C. THE PRIORITY FOR PROJECT DIMENSIONS SHALL BE IN THE FOLLOWING ORDER:
<br />1. CODE MINIMUM - MAXIMUM DIMENSIONS AND CLEARANCES
<br />2. STRUCTURAL GRID LINES
<br />3. LOAD BEARING CAST -IN -PLACE AND/OR CONCRETE MASONRY UNIT WALLS
<br />4. STEEL STRUCTURE
<br />5. FRAMED WALLS EXTERIOR
<br />6. FRAMED WALLS INTERIOR
<br />7. DOORS AND WINDOWS
<br />8. EXTERIOR GLAZING SYSTEMS
<br />9. INTERIOR GLAZING SYSTEMS
<br />D. FLOOR ELEVATIONS ARE INDICATED TO THE FACE OF THE STRUCTURAL SLAB - UNLESS OTHERWISE NOTED
<br />E. VERTICAL DIMENSIONS ARE INDICATED FROM THE FLOOR ELEVATION TO THE FACE OF MATERIAL AT THE DIMENSION POINT -UNLESS OTHERWISE NOTED
<br />F. CEILING HEIGHTS ARE INDICATED FROM THE FLOOR ELEVATION TO FACE OF THE FINISHED MATERIAL AS SCHEDULED
<br />G. DIMENSIONS SHOWN ON THE DRAWINGS SHALL INDICATE THE REQUIRED SIZE, CLEARANCE AND DIMENSIONAL RELA T !ONSHIP BE! V? EEN FF C JECT SYSTENIS
<br />AND COMPONENTS - DIMENSIONS SHALL NOT BE DETERMINED BY SCALING THE DRAWINGS.
<br />\�l
<br />f�
<br />S(l
<br />desicin
<br />STyles
<br />architecture
<br />/0� Columbus
<br />Tampa, Florida 33605
<br />p 813 2.:1 67CK t t 812 2 47 3757
<br />design tvif_b�c cii ec*ure.corr,
<br /># AACKY)339 3
<br />All reproduction & intellectual property
<br />tights reserved 2017
<br />i
<br />Project
<br />rw -
<br />.a
<br />Ct
<br />DMG TI) �.
<br />H'ii H i d
<br />i
<br />5935 7th Street Ze�hy�rhills,
<br />FL 33542
<br />Prepared ;.r
<br />j
<br />In Association wit"
<br />HEES & ASSOCIATES, INC,
<br />CONTACT' K. RL i REF')'
<br />1.,S 1 5TH S i
<br />SAFRASOTA, FL 3-236
<br />PHONE: 9,11.955.4555
<br />GENESIS ENGINEER GROUP, LLC
<br />CONTACT: MIKE HANNEY
<br />1000 N. ASHLEY DR. #900
<br />TAMPA. FL
<br />PHONE. 813.52'?.6455
<br />GENESIS ENGINEER GROUP, LI-C
<br />CONTACT: M!KE HANEY
<br />1000 N. ASHLEY DR. #900
<br />TAMPA, FL
<br />PHONE: 813.523.6455
<br />PossionA gel
<br />A.
<br />Pew J. t}ahnrt R # 12/10/2018
<br />15805 11:22:34 AM
<br />`io. Revision I;eEcrioti,)n Date
<br />i FERIM!TAN D BID SET '12/10/2018
<br />i
<br />No. Revision Description Date
<br />i
<br />I
<br />Drawn B,: WJ Checked By: SRS
<br />I
<br />Project Number 18190
<br />Sleet Tit!e
<br />i GP, -: ERA/ NO-jrE5
<br />I
<br />i
<br />I
<br />Original dra,M.ng i124 x 06 D3 not
<br />scale contents erawmgj
<br />Sheet Nurnber
<br />
|