Laserfiche WebLink
SHINGLE OR TILE ROOF PER <br />COMMUNITY SPECS - INSTALLED <br />PER MANUFACTURERS <br />SPECIFICATIONS —� <br />SHINGLE OR TILE ROOF PER <br />COMMUNITY SPECS - INSTALLED <br />PER MANUFACTURERS <br />SPECIFICATIONS ---, <br />12 <br />5[�,7� <br />12 <br />5� <br />I I t <br />6-0" <br />5068 SGD <br />REAR ELEVATION — B1 <br />SCALE: 1 /4"=V-0" <br />13'-0" RIDGE VENT <br />LEFT ELEVATION <br />— B1 <br />1 /4"=1 "-01 <br />" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-V crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with V dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861, <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for T pe 1 felt or other approved <br />water -resistive barrier shall be ap led over studs or sheathing of <br />all exterior walls. No. 15 asphalt fel shall be applied horizontally, <br />with the upper layer lapped over the wer layer not less than 2 <br />inches. Where joints occur, felt shall be ped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved fleshings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />c� <br />c <br />93 <br />O <br />� W <br />o <br />tie- E— o <br />=�mx <br />ra o <br />'N-ao <br />y <br />w m <br />i <br />d <br />6 <br />`OWN <br />«" •NN <br />� E cw <br />LLL <br />< �c} U � : <br />F �•� �` d <br />O F S S1 <br />E <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />_ H <br />W E <br />4 8 <br />O N 0 <br />V <br />O U � N <br />T <br />iii rn r r .w 1 J <br />N O <br />z Q— L LL w <br />,n J LLL:L a <br />— O 4 0 se <br />Z <br />L @ 4 <br />�10`�C <br />(a N 0 S <br />W <br />in�pjO' m w <br />Z N Cl)Z <br />N <br />OLL . . <br />U o <br />Z <br />W ❑a <br />0 <br />z N c, <br />a <br />z <br />z o <br />N <br />W <br />Ln z <br />0 <br />w m <br />U <br />w o <br />01) <br />JM <br />(J <br />W J_ <br />m .... <br />e <br />_ 8 <br />t <br />ai <br />z. <br />U 3 h <br />� <br />¢ <br />o <br />No <br />I� <br />O <br />� <br />w <br />M <br />Cl)oo <br />z <br />Q <br />J <br />L.L <br />Q E <br />tt <br />o <br />z® <br />oa <br />_ <br />oo <br />o <br />O E <br />O(V <br />aF <br />U <br />Qoo <br />4 <br />aQ <br />Z <br />�w <br />L <br />rp <br />p <br />z <br />m <br />o <br />VJ C <br />o< <br />U <br />0 <br />z� <br />J <br />< <br />Q w <br />Z <br />(n <br />z <br />z <br />o <br />�U <br />N <br />n "`!!!! <br />24 <br />a <br />�Z <br />W <br />W <br />C> <br />m� <br />Q Y <br />~3 <br />= r <br />� <br />O <br />UJ � <br />oNJzla <br />d � <br />3 <br />2 Ci <br />Lh <br />LOrn <br />.-� <br />Q <br />0 <br />^L0^,, <br />i <br />CID r <br />N <br />� <br />CT <br />Y <br />T <br />rr^^ <br />vl <br />m <br />m <br />L <br />r <br />dI <br />: <br />p <br />CD <br />N <br />0) <br />Ln <br />E <br />@ <br />o <br />Z <br />Z <br />E (� •' <br />ro <br />a <br />U Q p <br />JOB <br />NO: 22-06475 <br />SCALE : AS NOTED <br />SHEET NO. <br />3.2 <br />