|
ELECTRICAL EQUIPMENT SPECIFICATIONS
<br />PANELS: SQUARE D TYPE NQODCU RECESSED MOUNTED COPPE BUS, BOLTED CIRCUIT
<br />BREAKER PANELBOARD, 120/208 VOLT, 3PH., 4 WIRE OR EQUIVALENT.
<br />TIME CLOCK: COORDINATE WITH ELECTRICAL CONTRACTOR
<br />DUPLEX RECEPTACLES: HUBBELL #5262-WHI. UNLESS OTHERWISE NOTED.
<br />DUPLEX RECEPTACLES: HUBBELL #5262-BL. UNLESS OTHERWISE NOTED.
<br />QUAD RECEPTACLE: TWO (2) HUBBELL #5262-WHI DUPLEX RECEPTACLES IN COMMON
<br />JUNCTION BOX WITH 4 GANG COVER PLATE UNLESS OTHERWISE NOTED.
<br />ISOLATED GROUND RECEPTACLES: HUBBELL #IG-5262-WHI UNLESS OTHERWISE NOTED.
<br />ISOLATED GROUND QUAD RECEPTACLES: TWO (2) HUBBELL MG-5262-WHI DUPLEX
<br />RECEPTACLES IN COMMON JUNCTION BOX WITH 4 GANG COVER PLATE UNLESS
<br />OTHERWISE NOTED.
<br />GROUND FAULT RECEPTACLE: HUBBELL #GF-5252-WA UNLESS OTHERWISE NOTED.
<br />SINGLE POLE SWITCHES: HUBBELL #HBL-1221-WHI.
<br />ELECTRICAL NOTES
<br />REMOVE ALL EXISTING LIGHTING FIXTURES, SWITCHES, JUNCTION BOXES, CONDUIT,
<br />WIRING, ETC., NOT REQUIRED FOR REUSE.
<br />THE EXISTING 200 AMP 120/208 VOLT 3 PHASE SERVICE SHALL BE REUSED. ELECTRICAL
<br />CONTRACTOR SHALL EXTEND THE EXISTING SERVICE TO THE NEW PANEL LOCATION. BASE BID
<br />SHALL INCLUDE ANY ADDITIONAL CONDUIT AND WIRING AND CONNECTIONS OF THE ELECTRICAL
<br />EQUIPMENT, ETC.
<br />THE EXISTING SERVICE DISTRIBUTION EQUIPMENT INCLUDING THE METER AND THE 200 AMP
<br />MAIN DISCONNECT SWITCH SHALL REMAIN AND BE REUSED. VERIFY AND CHANGE AS
<br />REQUIRED TO ADEQUATELY PROTECT THE FEEDER TO THE SPACE. IF ANY ISSUES ARISE WITH
<br />REGARD TO REUSE OF SERVICE AND EQUIPMENT, CONTACT ARCHITECT AND/OR ENGINEER PRIOR
<br />TO BID FOR DISPOSITION. THE ELECTRICAL CONTRACTOR SHALL FIELD VERIFY AND VIEW ALL
<br />EXISTING CONDITIONS BEFORE SUBMITTING A PROPOSAL FOR THE WORK AS DESCRIBED AND
<br />SHOWN. EXTRAS WILL NOT BE PERMITTED FOR FAILURE TO MAKE THIS VISIT.
<br />THE INTENT OF THE WORK WITH REGARD TO ELECTRICAL DISTRIBUTION AS INDICATED ON
<br />THE DRAWINGS IS AS FOLLOWS:
<br />A. ALL EXISTING ELECTRICAL EQUIPMENT NOT CURRENTLY BEING USED TO FEED
<br />ANYTHING AND NOT REQUIRED AS PART OF THIS REMODEL SHALL BE REMOVED.
<br />B. EXISTING ELECTRICAL EQUIPMENT CURRENTLY BEING USED TO FEED LIGHTING,
<br />EQUIPMENT, ETC, SHALL BE REUSED. A DETAILED FIELD INSPECTION OF THE
<br />EXISTING EQUIPMENT SHALL BE INCLUDED IN THE BASE BID TO DETERMINE ITS
<br />CONDITION AND COSTS TO PERFORM MAINTENANCE SERVICE. INSPECTION SHALL
<br />INCLUDE THE FOLLOWING:
<br />1. CHECK ENTIRE INSTALLATION FOR CODE COMPLIANT CLEARANCES.
<br />MODIFY INSTALLATION AND EQUIPMENT LOCATION AS REQUIRED.
<br />2. CHECK CONDUITS FOR PROPER INSTALLATION, I.E. TIGHT
<br />CONNECTIONS, PROPER FITTINGS, RUSTING, CREASING, BENDING,
<br />ETC. REPAIR OR REPLACE AS REQUIRED.
<br />3. CHECK FOR BARE WIRING. COVER OR REPLACE AS REQUIRED.
<br />4. CHECK FOR PROPER GROUNDING OF SYSTEM AND EQUIPMENT. CORRECT
<br />AS REQUIRED.
<br />5. CHECK FOR CIRCUIT OVERLOADING AND/OR TRIPPING. REPLACE
<br />BREAKERS AND/OR FUSES AS REQUIRED. REDISTRIBUTE CIRCUITING
<br />OF EQUIPMENT AND/OR LIGHTING AS REQUIRED.
<br />6. REPAIR ANY RUSTED AREAS ON EQUIPMENT CASINGS. REPAINT AS
<br />REQUIRED.
<br />7. VERIFY THE SIZES OF THE EQUIPMENT IN FIELD AS SHOWN AND
<br />CALLED FOR - IF EQUIPMENT IS NOT SIZED AS REQUIRED, CONTACT
<br />THE ARCHITECT/ENGINEER.
<br />AN ALTERNATE PROPOSAL SHALL BE SUBMITTED TO REPLACE ANY AND/OR ALL EXISTING
<br />EQUIPMENT, IF THE EQUIPMENT IS DETERMINED TO BE IN NEED OF REPLACEMENT AFTER
<br />THE INSPECTION AT THE JOB SITE. ALTERNATE PROPOSAL SHALL BE COMPLETE.
<br />FURNISH AND INSTALL NEW ELECTRICAL PANELS AS REQUIRED.
<br />FURNISH AND INSTALL TYPEWRITTEN PANEL DIRECTORIES AS SHOWN.
<br />CIRCUITS SHALL BE CONNECTED TO THE PANELS AND ARRANGED TO COMPLY WITH THE
<br />NUMBERS SHOWN ON THE DRAWINGS. UNUSED CIRCUITS SHALL BE UTILIZED AS SPARES.
<br />PROVIDE ADEQUATE TEMPORARY POWER AND LIGHTING.
<br />MAINTAIN ALL REQUIRED CLEARANCES AT ALL ELECTRICAL EQUIPMENT AND COMPLY WITH
<br />N.E.C. ARTICLE 110.
<br />TIME CLOCK AND OTHER MISCELLANEOUS ELECTRICAL COMPONENTS SHALL NOT BE INSTALLED
<br />ON THE TELEPHONE TERMINAL BOARD.
<br />FURNISH AND INSTALL NEW FIRE ALARM SYSTEM (IF REQUIRED). COORDINATE WITH LANDLORD.
<br />TEMPERATURE CONTROL EXCLUDED FROM ELECTRICAL CONTRACT.
<br />CONTRACTOR SHALL NOTIFY THE ARCHITECT AND/OR ENGINEER OF ERRORS, OMISSIONS OR
<br />DISCREPANCIES BEFORE CONSTRUCTION OR FABRICATION OF AFFECTED WORK, OR, FAILING
<br />SUCH NOTICE, SHALL BE RESPONSIBLE FOR CORRECTING SAME WITHOUT COST TO TENANT,
<br />ARCHITECT OR ENGINEER.
<br />WORK SHALL INCLUDE START UP OF ALL SYSTEMS. PROVIDE ONE YEAR LABOR WARRANTY ON
<br />ENTIRE INSTALLATION AND ONE YEAR PARTS WARRANTY ON ALL EQUIPMENT SUPPLIED BY
<br />SUB -CONTRACTOR. FURNISH ALL MANUALS, MAINTENANCE INSTRUCTIONS, AND WARRANTIES
<br />TO CONTRACTOR.
<br />MOUNT SWITCHES 4'-0" ABOVE FLOOR UNLESS OTHERWISE NOTED.
<br />ALL CONDUITS FOR USE BY OTHERS SHALL BE CONTINUOUS, CONTAIN PULL STRINGS, AND
<br />HAVE PULL BOXES AS NECESSARY.
<br />ALL RECEPTACLE LOADS ARE BASED ON 180 WATTS FOR DUPLEX DEVICES AND 360 WATTS FOR
<br />QUAD DEVICES.
<br />ALL PANEL LOCK DEVICES MUST BE U.L. LABELED -LISTED.
<br />ALL ELECTRICAL EQUIPMENT AND MATERIAL SHALL BE SUITABLE FOR INSTALLATION AND USE IN
<br />CONFORMITY WITH NEC 110.3(A)(1).
<br />SEAL AROUND ALL ELECTRICAL PENETRATIONS OF FIRE RATED WALLS PER NEC 300.21.
<br />PANEL EXISTING P1 LUGS 225 AMP
<br />120/208 VOLT 3 PHASE 4 WIRE AIC RATING:22,000 MAIN BREAKER 200 AMP
<br />ORTIZ-3mgm
<br />m
<br />EX COND #1
<br />�■■�omm
<br />�■■
<br />COND #3 In
<br />Ron
<br />no
<br />a
<br />11100
<br />11100
<br />`
<br />®
<br />®'
<br />so�M®
<br />ME
<br />n
<br />EQUIP RECPT
<br />11100
<br />Wes■■�■■�on�n
<br />- • -
<br />11100
<br />`
<br />m_■■�■■�®_®®'
<br />11100
<br />PANEL P2_ FEED-
<br />11100
<br />®
<br />■■
<br />®0
<br />�
<br />_
<br />1
<br />'
<br />®IMME■■�■■�■■MO
<br />'
<br />11100
<br />11100
<br />_
<br />`
<br />MISSES
<br />■�■■�■■MO
<br />_ A.
<br />11100
<br />_
<br />`
<br />®_■■�■■�■■_®
<br />`
<br />11100
<br />®INNI■■�■■�■■IMMEm
<br />'
<br />11100
<br />• •
<br />®_■■�■■�■■_
<br />®
<br />• _
<br />11100
<br />�
<br />®�■■�■■�■■MO
<br />�
<br />11100
<br />.:.
<br />OMEN
<br />■■
<br />m
<br />. _ .
<br />11100
<br />"*" INDICATES PANEL LOCKS
<br />PHASE A:
<br />26912
<br />WATTS
<br />PHASE B:
<br />26424
<br />WATTS
<br />PHASE C:
<br />25980
<br />WATTS
<br />TOTAL
<br />79316
<br />WATTS
<br />BALANCE 3.46%
<br />CONNECTED
<br />79,316 W.
<br />220.3 A.
<br />PANEL EXISTING P2 LUGS 100 AMP
<br />120/208 VOLT 3 PHASE 4 WIRE AIC RATING:22,000 MAIN BREAKER 100 AMP
<br />WIRE
<br />SIZE
<br />USE
<br />CKT.
<br />NO.
<br />LOAD
<br />KVA
<br />BKR
<br />SIZE
<br />A B C
<br />BKR
<br />SIZE
<br />LOAD
<br />KVA
<br />CKT.
<br />NO.
<br />USE
<br />WIRE
<br />SIZE
<br />SPARE
<br />1
<br />20/1
<br />20/1
<br />2
<br />SPARE
<br />SPARE
<br />3
<br />4
<br />SPARE
<br />SPARE
<br />5
<br />250
<br />6
<br />SIGN
<br />LIGHTING
<br />7
<br />432
<br />1080
<br />8
<br />LOBBY RECPT
<br />LIGHTING
<br />9
<br />174
<br />360
<br />10
<br />RECEPTION RECPT
<br />LIGHTING
<br />11
<br />350
<br />360
<br />12
<br />GROOMING GFCI
<br />LIGHTING
<br />13
<br />650
<br />180
<br />14
<br />GROOMING RECPT
<br />LIGHTING
<br />15
<br />312
<br />180
<br />16
<br />1 GROOMING RECPT
<br />LIGHTING
<br />17
<br />342
<br />180
<br />18
<br />GEN RECPT
<br />SPARE
<br />19
<br />720
<br />20
<br />OFFICE RECPT
<br />SPARE
<br />21
<br />1080
<br />22
<br />STOCKROOM FGCI
<br />SPARE
<br />23
<br />1080
<br />24
<br />1 KENNEL RECPT
<br />SPARE
<br />25
<br />900
<br />26
<br />1 KENNEL RECPT
<br />SPARE
<br />27
<br />28
<br />SPARE
<br />SPARE
<br />29
<br />180
<br />30
<br />RESTROOM GFCI
<br />SPARE
<br />31
<br />32
<br />SPARE
<br />SPARE
<br />33
<br />34
<br />SPARE
<br />SPARE
<br />35
<br />36
<br />SPARE
<br />SPARE
<br />37
<br />180
<br />38
<br />WASHER
<br />SPARE
<br />39
<br />30/2
<br />2250
<br />40
<br />DRYER
<br />SPARE
<br />41
<br />L
<br />_F2250
<br />42
<br />"*" INDICATES PANEL LOCKS
<br />PHASE A: 4142 WATTS
<br />PHASE B: 4356 WATTS
<br />PHASE C: 4992 WATTS
<br />TOTAL 13490 WATTS
<br />BALANCE 17.03%
<br />CONNECTED
<br />67,332 W.
<br />187.0 A.
<br />EXISTINGDISC SW #1
<br />60/50, NEMA 3R
<br />EXISTING COND #1
<br />ON GROUND
<br />P1-16
<br />WR 20A. GFCI RECEPTACLE -
<br />IN WEATHER RESISTANT BOX
<br />3-#6 CU, 1 #8 GRD. 1 "C.
<br />NEW DISC SW #2
<br />60/50, NEMA 3R
<br />I I \
<br />NEW COND #1
<br />ON GROUND
<br />P1-16
<br />WR 20A. GFCI RECEPTACLE -
<br />IN WEATHER RESISTANT BOX
<br />3-#6 CU, 1 #8 GRD. 1 "C.
<br />NEW DISC SW #3
<br />30/30, NEMA 3R
<br />NEW COND #2
<br />ON GROUND
<br />WR 20A. GFCI RECEPTACLE -
<br />IN WEATHER RESISTANT BOX
<br />EXISTING DISC SW #4
<br />100/70, NEMA 1
<br />P1-16
<br />3-#4 CU, 1 #8 GRD. 1-1 /4"C.
<br />EXISTING AHU #1
<br />SUSPENDED
<br />WR 20A. GFCI RECEPTACLE
<br />IN WEATHER RESISTANT BOX
<br />NEW DISC SW #5
<br />100/70, NEMA 1
<br />P1-16
<br />3-#4 CU, 1 #8 GRD. 1-1 /4"C.
<br />NEW AHU #2
<br />SUSPENDED
<br />WR 20A. GFCI RECEPTACLE
<br />IN WEATHER RESISTANT BOX
<br />NEW DISC SW #6
<br />100/70, NEMA 1
<br />P1-16 11 11 P1-16
<br />3-#6 CU, 1 #8 GRD. 1 "C. I I I-- 3-#4 CU, 1 #8 GRD. 1-1 /4"C.
<br />EXTERIOR OF BUILDING I HOUNDSTOWN
<br />FIRST FLOOR
<br />4-#3/0 CU, 11 #4 GRD., 2"C.
<br />EXISTING TO REMAIN
<br />4-#3/0 CU, 1 #4 GRD., 2"C.
<br />EXISTING 200 AMP
<br />DISCONNECT SWITCH
<br />WITH 200 AMP FUSES
<br />CONNECT TO
<br />EXISTING
<br />O
<br />'
<br />R
<br />EXISTING
<br />225 AMP
<br />120/208V.
<br />EXISTING
<br />100 AMP
<br />120/208V.
<br />200A.
<br />PNL "P1"
<br />PNL "P2"
<br />200 AMP
<br />100 AMP
<br />BREAKER
<br />BREAKER
<br />RELOCATED
<br />RELOCATED
<br />EXISTING METER SOCKET TO REMAIN
<br />NEW METER BY E.C.
<br />4-#3 CU, 1 #4 GRD., 1-1 /4"C.
<br />RISER DIAGRAM NOTES
<br />1. OBTAIN AVAILABLE FAULT CURRENT RATING AND PROVIDE
<br />PROTECTION FOR MAIN CIRCUIT BREAKER AND ALL
<br />BRANCH DEVICES.
<br />2. MAINTAIN ALL REQUIRED CLEARANCES PER ARTICLE
<br />110-26 NEC
<br />POWER RISER DIAGRAM.
<br />NOT TO SCALE
<br />NEW AHU #3
<br />SUSPENDED
<br />WR 20A. GFCI RECEPTACLE
<br />IN WEATHER RESISTANT BOX
<br />2
<br />O
<br />_
<br />N
<br />� � � � Z
<br />W
<br />uj U
<br />w
<br />m NW%.:j
<br />Z
<br />I z
<br />�o
<br />Wo
<br />ON
<br />¢ o
<br />o 0)co
<br />tTm�:QO
<br />o�
<br />L2LZ
<br />mal
<br />CERTIFIED BY:
<br />6440 FORT KING
<br />ZEPHYRHILLS, FL
<br />33542
<br />DARREN & LUANN
<br />Owner
<br />LJANSEN GEHRING
<br />317.747.0555
<br />ZEPHYR HILLS
<br />ELECTRICAL
<br />SPECIFICATIONS
<br />E101
<br />
|