7441 Gall Blvd (2) - Laserfiche WebLink

Browse Search

_ L DIVISION 16 - ELECTRICAL SPECIFICATIONS PART I. GENERAL PROVISIONS 1. SCOPE: PROVIDE ALL LABOR, MATERIAL, AND EQUIPMENT IN ACCORDANCE WITH THESE SPECIFICATIONS, AND THE ACCOMPANYING DRAWINGS TO PROVIDE A COMPLETE AND PROPERLY OPERATING ELECTRICAL SYSTEM FOR THE BUILDING. A. THE CONTRACTOR SHALL FURNISH AND INSTALLALL OF THE FOLLOWING MATERIAL AND EQUIPMENT UNDER THIS DIVISION OF THE SPECIFICATIONS, UNLESS NOTED OTHERWISE: PANELBOARDS; LIGHTING FIXTURES; LAMPS; RACEWAYS; 600 VOLT WIRE AND CABLE; WIRING DEVICES; DEVICE PLATES; DEVICE, PULL, AND JUNCTION BOXES; SAFETY SWITCHES; MOTOR STARTERS; LIGHTING CONTROLS; CIRCUIT BREAKERS; FUSES; TIME CLOCKS; EQUIPMENT IDENTIFICATION (NAMEPLATES AND DIRECTORIES); WIRE AND CABLE TERMINATIONS; CONNECTIONS TO INDIVIDUAL UNITS OF EQUIPMENT FOR THE WALK-IN FREEZERS AND COOLERS; AND TEMPORARY POWER. B. THE FOLLOWING MATERIAL AND EQUIPMENT WILL BE FURNISHED AND/OR INSTALLED BY OTHERS, OR UNDER OTHER DIVISIONS OF THE SPECIFICATIONS, UNLESS NOTED OTHERWISE: LOW VOLTAGE (24 VOLT) WIRE AND CABLE, COMMUNICATION DEVICES, SECURITY EQUIPMENT, POINT OF SALE (POS) EQUIPMENT, SIGNAGE, CONCRETE BASES FOR SITE LIGHTING POLES. C. THE FOLLOWING MATERIALAND EQUIPMENT WILL BE FURNISHED BY OTHERS, OR UNDER OTHER DIVISIONS OF THE SPECIFICATIONS, AND INSTALLED BY THE CONTRACTOR, UNLESS NOTED OTHERWISE: SITE LIGHTING FIXTURES AND POLES. 2. GENERAL REQUIREMENTS: ALL WORK SHALL BE PERFORMED BY SKILLED LICENSED ELECTRICIANS IN ACCORDANCE WITH THE BEST PRACTICES OF THE TRADE, MEETING THE REQUIREMENTS OF THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE, APPLICABLE FEDERAL, STATE AND LOCAL CODES, AND THE REQUIREMENTS OF THE ELECTRICAL UTILITY COMPANY FURNISHING THE SERVICES. ALL NECESSARY CONSTRUCTION PERMITS AND CERTIFICATES OF INSPECTION SHALL BE PURCHASED AND OBTAINED UNDER THIS CONTRACT. A. COORDINATION: ALL OUTLETS MUST BE ACCURATELY LOCATED, PARTICULARLY APPLIANCE OUTLETS WHICH SHALL BE LOCATED FROM THE DIMENSIONS GIVEN ON THE DRAWING AND FIELD VERIFIED. REVIEW THE ARCHITECTURAL, PLUMBING AND HEATING AND VENTILATING PLANS IN ORDER TO COORDINATE THIS WORK WITH OTHER TRADES, AND COOPERATE WITH THEM IN THE ENTIRE INSTALLATION. 3. SERVICE VOLTAGE: THESE DRAWINGS ARE FOR A METERED, UNDERGROUND BUILDING SERVICE OF 120/208 VOLT, THREE PHASE, FOUR WIRE, 60 HERTZ. ALL KITCHEN AND AIR CONDITIONING EQUIPMENT HAS BEEN DESIGNED AND PURCHASED FOR USE ON THIS ELECTRICAL SYSTEM. THE CONTRACTOR SHALL CONTACT THE ELECTRICAL UTILITY AND VERIFY ALL OF THE ABOVE SERVICE CHARACTERISTICS, AND THE AVAILABLE FAULT CURRENT. 4. SERVICE EQUIPMENT: THE SERVICE SHALL BE LOCATED AS SHOWN ON THE SITE PLAN, OR AS INDICATED IN THE INSTRUCTIONS TO BIDDERS. UTILITY POLES, PADS FOR UTILITY TRANSFORMERS, CURRENT TRANSFORMER ENCLOSURES, METERING EQUIPMENT, SERVICE MASTS, AND OTHER RELATED MATERIALS AND EQUIPMENT SHALL BE APPROVED, FURNISHED, AND INSTALLED AS REQUIRED. INCLUDE THE COST OF ALL THE ABOVE ITEMS, SERVICE CONNECTIONS, AND METER CHARGES IN THE BASE BID. MAIN SERVICE SWITCHES AND CURRENT TRANSFORMER CABINETS SHALL BE INCLUDED IN THE BASE BID. UNLESS NOTED OTHERWISE, A MAIN SERVICE SWITCH WITH CURRENT LIMITING FUSES MAY BE USED WHEN THE AVAILABLE FAULT CURRENT (AFC) IS EXCESSIVE, IN ORDER TO USE STOCK PANELBOARDS, WITH 10K OR 22K AIC RATINGS. PART II. MATERIALS 1. MATERIALS: ALL MATERIALS SHALL BE NEW AND OF THE QUALITY INDICATED BY THE SPECIFIED BRAND NAMES. SUBSTITUTIONS OF MATERIAL OF EQUAL QUALITY BY OTHER MAJOR MANUFACTURERS OF COMMERCIAL EQUIPMENT MAY BE ACCEPTABLE PROVIDED A LIST OF SUCH SUBSTITUTIONS IS APPROVED IN WRITING BY POPEYE'S ARCHITECTURE AND ENGINEERING DEPARTMENT. THE CONTRACTOR SHALL SUBMITA SUBSTITUTION LIST IN TRIPLICATE AT LEAST FIVE DAYS PRIOR TO THE BID OPENING. A. PANELBOARDS: PANELBOARDS SHALL BE BOLT -IN CIRCUIT BREAKER TYPE, AS SHOWN ON THE PLANS. PANELS SHALL BE OF PANELBOARD CONSTRUCTION, 20 INCHES WIDE (MINIMUM), 5-3/4" TO 6-1/2" DEEP, UL LISTED, AND MEET UL 67, UL 50, AND FEDERAL SPECIFICATION W-P-115B AS TYPE 1, CLASS 1, WITH BOLT -ON CIRCUIT BREAKERS, COPPER BUS BARS, NEUTRAL BUS, GROUND BUS, AND A HINGED LOCKABLE DOOR. CABINETS SHALL BE CODE GAUGE, GALVANIZED STEEL, MOUNTED AS SHOWN. PROVIDE TYPEWRITTEN CIRCUIT DIRECTORIES WITH CLEAR PLASTIC PROTECTORS IN ALL PANELS. ALL WIRES SHALL BE TAGGED WITH PANEL AND CIRCUIT NUMBERS. PANEL "MP" SHALL BE UL LISTED AND LABELED AS SUITABLE FOR USE AS SERVICE ENTRANCE EQUIPMENT. APPROVED MANUFACTURERS OF PANELS ARE SQUARE D/TELEMECHANIQUE, CUTLER -HAMMER, GENERAL ELECTRIC, WESTINGHOUSE, AND SIEMENS (I-T-E). B. LIGHTING FIXTURES: ALL LIGHTING FIXTURES SHALL BE UL LISTED, COMMERCIAL QUALITY. REFER TO NATIONAL ACCOUNT SCHEDULE. REVIEW AT: WWW.POPEYESDEVELOPMENTCOM; PASSWORD: lagniappe C. LAMPS: ALL NEW FLUORESCENT LAMPS (F40T8) SHALL BE COOL WHITE, OR COLOR IMPROVED COOL WHITE, WITH A 4100 DEGREE K COLOR TEMPERATURE, 2950 MIN INITIAL LUMENS, 20,000 HOURS RATED LIFE, AND 62 MIN CRI, UNLESS NOTED OTHERWISE. D. WIRING DEVICES: ALL WIRING DEVICES SHALL BE UL LISTED, COMMERCIAL SPECIFICATION GRADE. SWITCHES SHALL BE RATED 20 AMPS AT 120/277 VOLTS, AC. STANDARD RECEPTACLES SHALL BE 20 AMP, DUPLEX, GROUNDING TYPE, IN NEMA CONFIGURATIONS, UNLESS NOTED OTHERWISE. SWITCHES IN THE SAME LOCATION SHALL BE GANGED BEHINDASINGLE PLATE. DEVICE PLATES IN THE KITCHEN AREA SHALL BE METAL, ALUMINUM OR STAINLESS STEEL. DEVICE PLATES IN THE DINING AREA SHALL BE THERMOPLASTIC PLASTIC (NYLON) OR METAL, COLOR AS APPROVED BY THE ARCHITECT OR OWNER. APPROVED MANUFACTURERS OF SWITCHES AND RECEPTACLES ARE HUBBELL, ARROW HART, BRYANT, LEVITON, PASS & SEYMOUR, GENERAL ELECTRIC, SLATER, OR EQUAL. 1. SWITCHES: a. SINGLE POLE: HUBBELL HBL1221-I, OR EQUAL. b. THREE WAY: HUBBELL HBL1223-I, OR EQUAL. 2. RECEPTACLES: a. NEMA 5-20R: HUBBELL 53621, OR EQUAL. b. NEMA 5-20R-IG: HUBBELL IG-5362, OR EQUAL. c. NEMA 5-20R-IG/SS: HUBBELL IG-5362-OS, OREQUAL. d. NEMA 5-20R-GFCI: HUBBELL GF5362-I, OR EQUAL. e. NEMA 6-20R: HUBBELL 5462-I, OR EQUAL. f. OTHERS: COMMERCIAL OR INDUSTRIAL GRADE, UL LISTED, FEDERAL SPECIFICATION WC596F. 3. WP PLATES: WEATHERPROOF COVERS ARE PERMITTED UNDER NEC ARTICLE 406.8(B)(1). 4. NATIONALACCOUNT REFER TO THE NATIONAL ACCOUNT DIRECTORY. THE FOLLOWING EQUIPMENT MAY BE AVAILABLE: MAIN SERVICE PANELBOARD WITH BREAKERS INSTALLED, LIGHTING AND DISTRIBUTION PANELBOARDS WITH BREAKERS INSTALLED, ROOF -TOP DISCONNECTS FOR HVAC UNITS AND KITCHEN HOOD FANS, LIGHTING CONTACTOR PANEL, AND SHUNT TRIP SYSTEMS (IF REQUIRED PER LOCAL CODE). 5. EXCAVATIONS: PERFORM ALL NECESSARY EXCAVATING AND BACK -FILLING REQUIRED FOR THIS INSTALLATION. ALL EXCAVATIONS BELOW THE BOTTOM OF FOOTINGS SHALL BE BACKFILLED WITH 3000 PSI CONCRETE. WHERE DITCHES ARE CUT FOR OUTSIDE RUNS OF CONDUIT, REPLACE AND TAMP THE EARTH IN 12" LAYERS AND LEAVE THE GROUND LEVEL AND EQUAL TO ITS ORIGINAL CONDITION. 6. CONDUITAND FITTINGS: CONDUIT PERMITTED: (A) RIGID GALVANIZED STEEL (RGS), (B) EMT, (C) PVC, AND (D) ENT TYPES UTILIZED SHALL BE RUN ONLY AS PERMITTED PER CODE. ALL WIRING SHALL BE RUN IN CONDUIT. CONDUIT PLACED IN CONCRETE OR RUN UNDERGROUND SHALL BE RIGID GALVANIZED CONDUIT OR PVC. IF PVC IS USED, ALL ELBOWS, SWEEPS AND STUB -UPS SHALL BE RGS. CONDUIT EXPOSED OR RUN IN MASONRY WALLS ABOVE GRADE MAY BE PVC OR EMT WHERE ALLOWED BY LOCAL CODES. IF EMT IS NOT PERMITTED, RIGID SCREWED GALVANIZED PIPE CONDUIT AND FITTINGS SHALL BE USED. IF SHIELDED CABLE IS REQUIRED FOR CONTROL CIRCUITRY, IT SHALL BE TAN, GREY OR ANY NEUTRAL COLOR OTHER THAN THAT AS SPECIFIED FOR POWER DISTRIBUTION. NO CONDUIT SMALLER THAN 3/4" SHALL BE INSTALLED EXCEPT FOR TWO -WIRE SWITCH LEGS. ALL CONDUIT BENDS SHALL BE FREE FROM DENTS AND KINKS. ALL CONDUITS SHALL BE ELECTRICALLY CONTINUOUS FROM THE SERVICE EQUIPMENT TO ALL OUTLETS, AND SHALL BE SECURED TO ALL METAL BOXES WITH ONE LOCK NUT OUTSIDE, AND ONE INSIDE THE BOX WITH A REINFORCED BAKELITE BUSHING. IF PVC, OR ENT, IS USED, THEN APPROPRIATE SIZED, ELECTRICALLY CONTINUOUS, BOND WIRES SHALL BE RUN FROM THE SERVICE EQUIPMENT TO ALL OUTLETS, AND SHALL BE SECURED TO EACH WIRING DEVICE PER THE NATIONAL ELECTRICAL CODE. WHERE CONNECTIONS ARE TO BE MADE BETWEEN CONDUIT TERMINATIONS AND MOTORS, EQUIPMENT, OR APPARATUS NECESSITATING FLEXIBLE CONNECTIONS, APPROVED FLEXIBLE CONDUIT SHALL BE USED. OUTDOOR CONNECTIONS TO FANS, HVAC UNITS, OR ROTATING EQUIPMENT SHALL B MADE WITH HELICAL WOUND, LIQUIDTIGHT, FLEXIBLE STEEL CONDUIT. EXPOSED CONDUIT SHALL BE SUITABLY SUPPORTED AT INTERVALS NOT TO EXCEED FIVE (5) FEET. DURING CONSTRUCTION, CONDUIT SHALL BE KEPT FREE OF ALL FOREIGN MATTER BY USE OF CAPPED BUSHINGS ON ALL TURNED UP ENDS. PAPER OR WOOD PLUGS ARE NOT ACCEPTABLE FOR THIS PURPOSE. 7. WIRE AND CABLES: ALL WIRE AND CABLES SHALL BE UNDERWRITERS LABORATORIES' LISTED, AND LABELED, AND CONFORM WITH APPLICABLE STANDARDS OF UL (44, AND 83), NEMA (WC-5, AND WC-7), IPCEA (S-61-402, AND S-66-524), FEDERAL SPECIFICATIONS (J-C-30A(1), AND HH-1-595C), ANSI, AND OTHER APPLICABLE INDUSTRY STANDARDS. CONNECTORS AND LUGS SHALL MEET UL PUBLICATION 486. ALL BRANCH CIRCUIT WIRING SHALL BE 600 VOLT, COPPER, 75 DEGREE C (MIN), TYPE THHN/THWN WITH A MINIMUM SIZE OF #12 AWG, UNLESS NOTED OTHERWISE. WIRE SIZES OF #8 AWG AND LARGER SHALL BE STRANDED. SERVICE AND FEEDER CABLES SHALL BE 600 VOLT, STRANDED COPPER, 75 DEGREE C (MIN), TYPE XHHW. ALL CIRCUITS SHALL HAVE A SEPARATE GROUND CONDUCTOR. PROVIDE GREEN -INSULATED GROUND WIRE IN ALL RACEWAYS, CABLE ASSEMBLIES, AND WHERE NOTED. SIZE EQUIPMENT GROUNDS PER TABLE 250-122 OF THE NATIONAL ELECTRICAL CODE. INSULATION COLOR CODES SHALL BE BLACK, RED, AND BLUE (PHASE), WHITE (NEUTRAL), AND GREEN (GROUND). A. ALL WIRING SHALL BE INSTALLED IN CONDUIT, EXCEPT WHERE SPECIFICALLY SHOWN ON THE DRAWINGS. NON-METALLIC SHEATHED (TYPE NM) CABLE IS NOT PERMITTED. B. ALL BRANCH CIRCUIT, COMMUNICATION, SIGNALING, AND CONTROL WIRING TO KITCHEN, FIRE PROTECTION, AND OTHER EQUIPMENT SHALL BE ROUTED ABOVE THE CEILING. VERIFY WHETHER OR NOT THE SPACE ABOVE THE CEILING IS USED AS A SPACE FOR RETURN AIR FOR THE ENVIRONMENTAL AIR SYSTEM. IF IT IS USED FOR RETURN AIR, PROVIDE APPROVED RACEWAYS FOR ALL OVERHEAD WIRING PER NEC ARTICLE 300-22(B). IF IT IS NOT "OTHER SPACE USED FOR ENVIRONMENTAL AIR", APPROVED LOW VOLTAGE CABLES MEETING THE REQUIREMENTS OF NEC ARTICLES 725 AND 760 MAY BE RUN WITHOUT RACEWAYS, UNO. ALL SAFETY CONTROL WIRING FOR FIRE PROTECTION SYSTEMS, SHUNT TRIPS, ETC. SHALL BE RUN IN A RACEWAY IN ACCORDANCE WITH NEC ARTICLES 725.25 AND 725.28. 8. SITE LIGHTING: THE G.C. WILL FURNISH THE SITE LIGHTING PACKAGE, AS REQUIRED FOR THE SPECIFIC LOCATION. UNDER THIS SPECIFICATION SECTION, PROVIDE 1" RIGID GALVANIZED STEEL ELECTRICAL CONDUIT, AND THE REQUIRED WIRING FROM THE PANEL TO THE POLE. SET FIXTURES AND POLES ON CONCRETE BASES, AS PROVIDED UNDER SPECIFICATION SECTION 3A: CONCRETE. GROUND/BOND ALL SITE LIGHTING FIXTURES/POLES PER THE NEC. THE BRANCH CIRCUIT CONDUCTORS SHALL BE INCREASED FROM #10 AWG TO #8 AWG IF THE HORIZONTAL DISTANCE FROM THE PANEL TO THE POLE IS GREATER THAN EIGHTY (80) FEET. ALL SITE LIGHTING SHALL BE CONTROLLED THROUGH THE LIGHTING CONTROL SYSTEM SHOWN ON THE DRAWINGS. REFER TO THE SITE PLAN FOR QUANTITYAND LOCATION OF ALL SITE LIGHTING. SET FIXTURES AS SPECIFIED, AND AIM AFTER DARK FOR UNIFORM LIGHT DISTRIBUTION. 9. SIGNAGE LIGHTING: PROVIDE A 1" RIGID GALVANIZED STEEL ELECTRICAL CONDUIT, AND WIRING, FROM THE PANEL TO ALL ILLUMINATED SIGNS AS SHOWN ON THE LIGHTING AND SITE PLANS. GROUND/BOND EACH SIGN. SIGNS WILL BE FURNISHED AND INSTALLED BY THE OWNER, OR UNDER A SEPARATE CONTRACT, UNO. POWER AND WIRING SHALL BE FURNISHED AND INSTALLED UNDER THIS SECTION OF THE SPECIFICATIONS. OTHER WIRING: A. FURNISH AND INSTALLALL POWER WIRING AND CONDUITAS INDICATED ON THE DRAWINGS FOR ROOF -TOP HVAC EQUIPMENT, KITCHEN HOOD FANS, AND WALK-IN FREEZERAND COOLER EQUIPMENT. DISCONNECT SWITCHES, AVAILABLE FROM THE NATIONAL ACCOUNT, SHALL BE FURNISHED AND INSTALLED FOR EACH UNIT OF HVAC EQUIPMENT, AND FOR KITCHEN EQUIPMENT WITHOUT ACORD AND PLUG. BEFORE ENERGIZING ANY EQUIPMENT, VERIFY THAT THE CORRECT POWER SUPPLY VOLTAGE, AMPACITY, AND PHASING HAS BEEN PROVIDED AT THE LOAD SIDE OF THE DISCONNECT. B. FURNISH AND INSTALL THE LIGHTING CONTACTOR PANEL, AND ALL ASSOCIATED POWER WIRING, AS INDICATED. THE LIGHTING CONTACTOR PANEL IS CUSTOM BUILT, AND AVAILABLE FROM THE NATIONAL ACCOUNT. 10. EMPTY CONDUIT: LEAVE A#12 AWG PULL WIRE IN ALL EMPTY CONDUITS. 11. BOXES AND WIREWAYS: ALL JUNCTION BOXES, PULL BOXES, WIREWAYS, ETC, SHALL BE SIZED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE. 12. EQUIPMENT IDENTIFICATION: PROVIDE NAMEPLATES FOR ALL PANELBOARDS, CONTROLS, AND OTHER ELECTRICAL EQUIPMENT. EQUIPMENT VISIBLE TO THE PUBLIC SHALL BE IDENTIFIED WITH ENGRAVED LAMINATED NAMEPLATES ATTACHED WITH STAINLESS STEEL FASTENERS. ELECTRICAL EQUIPMENT NOT VISIBLE TO THE PUBLIC MAY BE NEATLY IDENTIFIED WITH BLACK PERMANENT MARKERS. PART III. EXECUTION 1. TESTS: MAKE ALL TESTS NECESSARY TO ENSURE THAT THE ENTIRE INSTALLATION IS FREE FROM IMPROPER GROUNDS, AND FROM SHORTED AND/OR OPEN CONDUCTORS. VOLTAGE, CURRENT, AND ROTATION TESTS SHALL BE MADE BEFORE ANY MOTORS ARE PLACED IN OPERATION. ALL LOADS SHALL BE BALANCED ACROSS PHASES. CHECK TO SEE THAT ALL LIGHTS WORK, AND ARE CONTROLLED BY SWITCHES INDICATED ON DRAWINGS, OR CIRCUIT BREAKERS SO INDICATED ON PANEL SCHEDULE. 2. GUARANTEE: FURNISH A GUARANTEE IN WRITING TO THE OWNER THAT ALL WORK EXECUTED UNDER THIS SECTION IS FREE FROM DEFECTS OF MATERIALS AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM DATE OF FINAL ACCEPTANCE. IN ADDITION, DURING THE TERM OF THIS GUARANTEE, THE REPAIR AND/OR REPLACEMENT OF ANY DEFECTIVE WORK, AND ALL RESULTING DAMAGES SHALL BE MADE AT NO ADDITIONAL EXPENSE TO THE OWNER. 3. TEMPORARY POWER: AT THE PROJECT SITE, PROVIDE A 100 AMP, 120/240 VOLT, SINGLE PHASE, SERVICE WITH POWER OUTLETS ADEQUATE FOR TEMPORARY CONSTRUCTION POWER. TEMPORARY LIGHTING SHALL BE MAINTAINED IN ALL AREAS OF THE BUILDING UNTIL PERMANENT POWER SOURCES HAVE BEEN ENERGIZED. TEMPORARY SERVICE SHALL BE PROVIDED UNDER SECTION 1A OF THESE SPECIFICATIONS. 4. CLEAN-UP: LEAVE THE ELECTRICAL PORTION OF THE WORK IN A CLEAN AND FINISHED CONDITION. 5. SHOP DRAWINGS: PROVIDE SHOP DRAWINGS FOR THE FOLLOWING ITEMS: PANELBOARDS, LIGHTING FIXTURES. 6. AS -BUILT DRAWINGS: MAINTAIN AS -BUILT DRAWINGS, UPDATED DAILY DURING CONSTRUCTION, AND PRESENT THE OWNER WITH ONE SET UPON COMPLETION. PROVIDE THE OWNER'S PERSONNEL WITH ON -SITE INSTRUCTION IN THE OPERATION AND MAINTENANCE OF THE COMPLETED ELECTRICAL SYSTEM. SYMBOL LIST SYMBOL DESCRIPTION MOUNTING 00 LIGHT FIXTURE, CEILING TYPE SEE FIXTURE LETTER INDICATES TYPE SCHEDULE SEE FIXTURE yyy TRACK LIGHTING SCHEDULE SWITCH, SINGLE POLE -LETTER 48" AFF TO CL S INDICATES LIGHTS CONTROLLED OR AS NOTED S SWITCH, THREE WAY u AFF TO CL OR AS NOTED S DIMMER SWITCH 48" AFF TO CL OR AS NOTED S SWITCH, DOUBLE POLE 48" AFF TO CL OR AS NOTED SINGLE RECEPTACLE, 125V, 20A IS" AFF TO CL OR AS NOTED O SINGLE RECEPTACLE, 125V, 20A FLUSH WITH FLOOR (FLUSH FLOOR BOX) DUPLEX RECEPTACLE, 125V, 20A 24" AFF TO CL OR AS NOTED DUPLEX RECEPTACLE, 125V, 20A 46" AFF TO CL OR AS NOTED GFI DUPLEX RECEPTACLE, 125V, 20A 24" AFF TO CL GROUND FAULT OR AS NOTED WIP DUPLEX RECEPTACLE, 125V, 20A IS" AFF TO CL WEATHERPROOF OR AS NOTED DUPLEX RECEPTACLE, 125V, 20A 46" AFF TO CL GROUND FAULT OR AS NOTED DUPLEX RECEPTACLE, 125V, 20A FLUSH WITH CEILING C FLUSH CEILING BOX 0__ 1 QUADRAPLEX FRECEPTACLE, 125V, 20A 24" AFF TO CL OR AS NOTED IG(5- DUPLEX RECEPTACLE, 125V, 20A 24" AFF TO CL WITH ISOLATED GROUND OR AS NOTED QUADRAPLEX RECEPTACLE, 125V, 20A 48" AFF TO CL OR AS NOTED O SPECIAL f;mCEPTACLE AS NOTED 24" AFF TO CL OR AS NOTED - PANELBOARD 120/208V SEE PANEL SCHEDULE L DISCONNECT SWITCH • TOP 60" AFF SIZE/ FUSE/ OF POLES OR AS NOTED LIM COMBINATION MOTOR STARTER TOP 60" AFF DISCONNECT SWITCH OR AS NOTED 4 MOTOR AS NOTED SM MOTOR STARTER SWITCH WITH NOTED OVERLOAD RELAYS AS REQUIRED` ELECTRIC DUCT HEATER WITH AS NOTED DISCONNECT SWITCH ■ DEVICE AS NOTED AS NOTED 0 TRANSFORMER AS NOTED OUTLET BOX WITH FLEXIBLE AS NOTED OR CONDUIT CONNECTION TO EQUIPMENT REQUIRED © OUTLET, JUNCTION OR AS NOTED OR PULL BOX REQUIRED I DRIVEN GROUND, UNLESS I NOTED OTHERWISE CONDUIT CONCEALED IN CEILING NUMBER OF WIRES SPACE OR WALL INDICATED AS FOLLOWS TWO WIRES --�- CONDUIT IN FLOOR SLAB, CEILING SLAB OR UNDERGROUND THREE WIRES I. HOME RUN TO PANEL (HASH MARKS FOUR WIRES - INDICATE NUMBER OF WIRES) �� CONDUIT RUN EXPOSED O O REFER TO LIKE NUMBERED NOTES D COMMUNICATIONS OUTLET 24" AFF OR AS NOTED COMMUNICATIONS OUTLET 48' AFF OR AS NOTED S DUCT TYPE SMOKE DETECTOR HVAC D RK DUCTWORK ® FAN SHUT DOWN RELAY AS NOTED 0 DUCT DETECTOR TEST/RESET 48 AFF OR AS NOTED © DOOR BUZZER AS NOTED �. DOOR BUZZER PUSHBUTTON AS NOTED NOTE ALL MOUNTING HEIGHTS SHOWN ARE TO THE CENTERLINE OF THE DEVICE UNLESS NOTED OTHERWISE. NOT ALL SYMBOLS APPEAR ON PLANS. ABBREVIATIONS AFF - ABOVE FINISHED FLOOR AHU - AIR HANDLING UNIT BFG - BELOW FINISHED GRADE C - CONDUIT CL - CENTERLINE CW - COOL WH 1 TE DACP - DOOR ALARM CONTROL PANEL DN - DOWN EF - EXHAUST FAN EG - EQUIPMENT GROUND ENCL - ENCLOSURE EWC - ELECTRIC WATER COOLER EWH - ELECTRIC WATER HEATER FCU - FAN COIL UNIT FHP - FRACTIONAL HORSE POWER FLA - FULL LOAD AMPERES G - GROUND GFI - GROUND FAULT INTERRUPTER HID - HIGH INTENSISTY DISCHARGE HORIZ - HORIZONTAL IG - ISOLATED GROUND LW - LIGHT WHITE HP - HORSEPOWER, HEAT PUMP HVAC - HEATING, VENTILATING, AIR CONDITIONING JB - JUNCTION BOX LRA - LOCKED ROTOR AMPERES MCB - MAIN CIRCUIT BREAKER MLO - MAIN LUGS ONLY N - NEUTRAL NL - NIGHT LIGHT OB - OUTLET BOX PB - PULL BOX, PUSHBUTTON PS - PAY STATION RECEPT - RECEPTACLE RLC - RELOCATED SPEC - SPECIFICATIONS TTB - TELEPHONE TERMINAL BOARD TVTB - TELEVISION TERMINAL BOARD VERT - VERTICAL WP - WEATHERPROOF uW - WARM WHITE XFMR - TRANSFORMER MANUFACTURER: SQUARE D MLO OR MCB: MLO PANEL: A TYPE: EXISTING FEED: BOTTOM VOLTAGE: 120/208V, 3 0, 4 WIRE MOUNTING: FLUSH CUORALWIRE: CU MAIN AMPS: 150AMP LOCATION: BACKWALL AICRATING: 10,000AMPS FEEDER: 150 AMP BREAKER OPTIONS: NOTES: - EXISTING BREAKER NEW CIRCUIT I,- ISOLATED GROUND CIRCUIT & - PROVIDE BREAKER LOCK -OUT DEVICE CKT CKT NO. LOAD OPT CODE KVA WIRE BRKR PHASE BRKR WIRE KVA CODE OPT: LOAD NO. 1 RECEPTACLES DINING :# R 0.54 12 20 A 20 12 1.08 R # & : SECURITY CAMERA RECEPT 2 3 RECEPTACLES DINING # R 0.72 12 20 B 20 12 0.86 E # : BAG-N-BOX CARBONATOR K42 4 5 BEVERAGE DISP DINING K-32 # E 0.48 12 20 C 20 12 0.36 R # & SECURITY SYSTEM OFFICE 6 7 POS DRIVE THRU P-20 , P-30 # ! R 0.54 12 20 A 20 12 0.50 R # MUSIC SYSTEM OFFICE 8 9 RECEPTS KITCHEN # R 0.90 12 20 B 20 12 0.54 R # ! POS SYSTEM OFFICE 10 11 SAFE M30 # & R 0.60 12 20 C 20 12 0.50 R # ! COMPUTER PRINTER OFFICE 12 13 BEVERAGE DISP DRIVE TH K-31 ;# R 0.18 12 20 A 20 12 0.36 R # RECEPTS OFFICE 14 15 REFRIGERATOR UPRIGHT B60 # & E 1.38 12 20 B 20 12 1.00 E # DRIVE THRU AUDIO SYSTEM 16 17 REFRIGERATOR UPRIGHT A54 # & E 1.38 12 20 C 20 12 1.00 R # ! :VIDEO MONITORS 18 19 ICE BATTER TABLE A47.4 # & E 0.30 12 20 A 20 12 0.10 E # : DOOR BUZZER 20 21 MARINATOR A31 # E 0.75 12 20 B 20 12 1 # SPARE 22 23 BREWER TEA COFFEE K71 # K 1.70 12 20 C 20 12 I # • SPARE 24 25 POS DINING P-20 , P-30 # ! R 0.72 12 20 A 20 12 1 # SPARE 26 27 RECEPT TELEPHONE BOARD # & R 0.36 12 20 B 20 12 1 # 'SPARE 28 29 SPARE # 1 12 20 C 20 12 1 # :SPARE 30 31 SPARE # 1 12 20 A 20 12 1 # :SPARE 32 33 SPARE # 1 12 20 B 20 12 I # :SPARE 34 35 SPARE # 1 12 20 C 2P 15 12 1 # :SPARE # 36 37 SPARE # 1 12 20 A 12 1 38 39 SPACE I B 40 41 SPACE ClI 42 KVA PER PHASE= BUS A: 4.32 DEMAND BUS B: 6.51 KVA FACTOR DEMAND KVA BUS C: 6.02 (L) LIGHTING: 0.00 X 1.25 = 0.00 TOTAL KVA: 16.85 (R) RECEPTACLES: 8.90 X 1.00 = 8.90 (R) RECEPTACLES: 0.00 X 0.50 = 0.00 PANEL CALCULATIONS (H) HVAC: 0.00 X 1.00 = 0.00 DEMAND KVA: 16.26 (E) EQUIPMENT: 6.25 X 1.00 = 6.25 TIMES 1000 JOB NAME: (K) KITCHEN EQUIPMENT: 1.70 X 0.65 = 1.11 DIVIDED BY 1.732 Popeye's Zephyrhills (S) SUBFEED: 0.00 X 1.00 = 0.00 DIVIDED BY 208 MPS #: LARGEST MOTOR: 0.00 X 0.25 = 0.00 213027 TOTAL DEMAND KVA: 16.26 PANEL DEMAND AMPS: 45.12 DATE LAST MODIFIED 3/21/2013 MANUFACTURER: SUQARE D MLO OR MCB: MLO PANEL: B TYPE: EXISTING FEED: BOTTOM VOLTAGE: 120/208V, 3 0, 4 WIRE MOUNTING: FLUSH CUORALWIRE: CU MAIN AMPS: 200AMPS LOCATION: BACK WALL AICRATING: 10,000AMPS FEEDER: 200AMPS BREAKER OPTIONS: NOTES: # - EXISTING BREAKER NEW CIRCUIT % - EXISTING BREAKER EXISTING CIRCUIT A - WIRE CIRCUIT THROUGH LIGHTING CONTACTOR AS SPECIFIED ON PLAN & - PROVIDE BREAKER LOCK -OUT DEVICE CKT CKT NO. LOAD ;OPT CODE KVA WIRE BRKR PHASE BRKR WIRE KVA CODE OPT; LOAD NO. 1 MENUBOARD DRIVE THRU Q20 # A L 1.00 10 20 A 20 12 0.65 L # : LIGHTS DINING SWITCH a 2 3 DIRECTION SIGNS # A L 1.00 10 20 B 20 12 0.54 L # : LIGHTS DINING SWITCH b 4 5 LIGHTS COOLER FREEZER % & L 1.00 12 20 C 20 12 0.58 L # • LIGHTS DINING SWITCH c 6 7 LIGHTING CONTACTOR CONTROL # & E 0.25 12 20 A 20 12 1.19 L # LIGHTS KITCHEN SWITCH d 8 9 CANOPY LIGHTS # A L 0.70 10 20 B 20 12 1.04 L # LGTS KIT RESTROOM SWITCH a 10 11 CANOPY LIGHTS # A L 0.80 10 20 C 20 12 SPARE 12 13 CANOPY LIGHTS # A L 1.00 10 20 A 20 12 1 SPARE 14 15 MENUBOARD DINING Q10 # L 1.00 12 20 B 2P 20 10 1.60 L % A : PARKING LOT LIGHTS % A : EXISTING 16 17 ROOF CAP % L 0.50 12 20 C 10 1.60 L 18 19 SPARE : # 1 12 20 A 2P 20 10 1.60 L % A : PARKING LOT LIGHTS % A : EXISTING 20 21 SPARE # 1 12 20 B 10 1.60 L 22 23 SPARE # 1 12 20 C 2P 20 10 1.60 L % A PARKING LOT LIGHTS % A EXISTING 24 25 SPARE # 1 12 20 A 10 1.60 L 26 27 SPARE # 1 12 20 B 20 12 1.00 L # A 'BUILDING MOUNTED SIGN 28 29 SPARE # 1 12 20 C 20 12 1.00 L # A BUILDING MOUNTED SIGN 30 31 SPARE # 1 12 20 A 20 12 1.00 L # A BUILDING MOUNTED SIGN 32 33 SPARE # 1 12 20 B 20 12 1.00 L # A : BUILDING MOUNTED SIGN 34 35 SPARE : # 1 12 20 Ct20 12 1 :SPARE 36 37 SPARE # 1 12 20 A 12 1 SPARE 38 39 PYLON SIGN # A L 1.00 10 20 8 12 1 SPARE 40 41 SPARE # 1 12 20 C 20 12 1 SPARE 42 KVA PER PHASE= BUS A: 8.29 DEMAND BUS B: 10.48 KVA FACTOR DEMAND KVA BUS C: 7.08 (L) LIGHTING: 25,60 X 1.25 = 32.00 TOTAL KVA: 25.65 (R) RECEPTACLES: 0.00 X 1.00 = 0.00 (R) RECEPTACLES: 0.00 X 0.50 = 0.00 PANEL CALCULATIONS (H) HVAC: 0.00 X 1.00 = 0.00 DEMAND KVA: 32.25 (E) EQUIPMENT: 0.25 X 1.00 = 0.25 TIMES 1000 JOB NAME: (K) KITCHEN EQUIPMENT: 0.00 X 0.65 = 0.00 DIVIDED BY 1.732 Popeye's Zephyrhills (S) SUBFEED: 0.00 X 1.00 = 0.00 DIVIDED BY 208 MPS #: LARGEST MOTOR: 0.00 X 0.25 = 0.a 213027 TOTAL DEMAND KVA: 32.25 PANEL DEMAND AMPS: 89.52 DATE LAST MODIFIED X21/2013 MANUFACTURER: SUQARE D MLO OR MCB: MLO PANEL: C TYPE: EXISTING FEED: BOTTOM VOLTAGE: 120/208V, 3 (0, 4 WIRE MOUNTING: FLUSH CUORALWIRE: CU MAIN AMPS: 150 AMPS LOCATION: BACK WALL AICRATING: 10,000 AMPS FEEDER: 150 AMPS BREAKER OPTIONS: NOTES: # - EXISTING BREAKER NEW CIRCUIT $ - NEW BREAKER NEW CIRCUIT & - PROVIDE BREAKER LOCK -OUT DEVICE CKT CKT NO. LOAD :OPT CODE KVA WIRE BRKR PHASE BRKR WIRE KVA CODE OPT; LOAD NO. 1 HOLDING UNIT SIDES (D92) # # K 1.67 12 2P 20 A 2P 20 12 1.75 K # & :PRODUCTION COUNTER (H10.4PD) # & : 2 3 K 1.67 12 B 12 1.75 K 4 5 HOLDING UNIT SIDES (D92) # # K 1.67 12 2P 20 C 2P 20 12 0.63 K # & • HOT FOOD WELL (H10.4PD) # & 6 7 K 1.67 12 A 12 0.63 K 8 9 HOLDING UNIT (D94) $ $ K 2.85 10 2P 30 B 2P 20 12 0.45 E # & HEAT LAMPS (H10.4PD) # & 10 11 K 2.85 1 10 C 1 12 1 0.45 E 12 13 CHICKEN HOLDING UNIT (D93) $ & $ & K 3.08 8 2P 40 A 20 12 1.50 K # ; TOASTER VERT C20 14 15 K 3.08 8 B 20 12 0.78 K # & SANDWICH FRIDGE C10.27 16 17 UNDER COUNTER FRIDGE J40 # & E 0.58 12 20 C 20 12 0.55 K # HOLDING UNIT C30 18 19 PACK STATION DIP WELL (D30) : # & # & E 0.62 12 2P 20 A 2P 30 10 2.00 E $ : HOT WATER DISP (D70) $ : 20 21 E 0.62 12 B 10 2.00 E 22 23 MICROWAVE (D20) $ $ K 2.00 10 2P 30 C 2P 30 10 2.00 E $ HOT WATER DISP (D70) $ 24 25 K 2.00 10 A 10 2.00 E 26 27 MICROWAVE (D20) $ $ K 2.00 10 2P 30 B 25 10 2.32 K $ HOLDING CABINET D90 28 29 K 2.00 10 C 2P 20 12 1.24 E $ ICE CUBER (K10) $ 30 31 BISCUIT HOLDING B65 # K 1.00 12 20 A 12 1.24 E 32 33 FLY FAN # E 0.50 12 20 B I SPACE 34 35 SPARE 20 C I SPACE 36 37 SPARE 1 20 A I SPACE 38 39 SPACE I B I SPACE 40 41 SPACE I I ClI SPACE 42 KVA PER PHASE= BUS A: 19.16 DEMAND BUS B: 18.02 KVA FACTOR DEMAND KVA BUS C: 13_97 (L) LIGHTING: 0.00 X 1.25 = 0.00 TOTAL KVA: 51.15 (R) RECEPTACLES: 0.00 X 1.00 = 0.00 (R) RECEPTACLES: 0.00 X 0.50 = 0.00 PANEL CALCULATIONS (H) HVAC: 0.00 X 1.00 = 0.00 DEMAND KVA: 38.04 (E) EQUIPMENT: 13.70 X 1.00 = 13.70 TIMES 1000 JOB NAME: (K) KITCHEN EQUIPMENT: 37.45 X 0.65 = 24.34 DIVIDED BY 1.732 Popeye's Zephyrhills (S) SUBFEED: 0.00 X 1.00 = 0.00 DIVIDED BY 208 MPS #: LARGEST MOTOR: 0.00 X 0.25 = 0.00 213027 TOTAL DEMAND KVA: 38.04 PANEL DEMAND AMPS: 105.60 DATE LAST MODIFIED 3/21/2013 MANUFACTURER: SUQARE D MLO OR MCB: MLO PANEL: D TYPE: EXISTING FEED: BOTTOM VOLTAGE: 120/208V, 3 0, 4 WIRE MOUNTING: FLUSH CUORALWIRE: CU MAINAMPS: 400AMPS LOCATION: BACK WALL AICRATING: 10,000 AMPS FEEDER: 400 AMPS BREAKER OPTIONS: NOTES: #- EXISTING BREAKER NEW CIRCUIT %- EXISTING BREAKER EXISTING CIRCUIT & - PROVIDE BREAKER LOCK -OUT DEVICE $ - NEW BREAKER NEW CIRCUIT CKT CKT NO. LOAD ;OPT CODE KVA WIRE BRKR PHASE BRKR WIRE KVA CODE OPT; LOAD NO. 1 WALK IN COOLER ; % & : % & : % & H 1.44 12 3P 15 A 20 12 1 # : SPARE 2 3 H 1.44 12 B 2P 60 6 4.75 K $ : CHUB WARMER (D81) $ : 4 5 H 1.44 12 C 6 4.75 K 6 7 WALK IN FREEZER % & °/a & % & H 2.40 10 3P 25 A 3P 30 10 1.87 K $ CONVECTION OVEN STACK $ 1 OF 2 $ 8 9 H 2.40 10 B 10 1.87 K 10 11 H 1 2.40 10 C 10 1.87 K 12 13 ROOF RECEPTACLES ; % & R 0.36 12 20 A 3P 30 10 1.87 K $ CONVECTION OVEN STACK $ : 2 OF 2 $ 14 15 HOOD EXHAUST FAN EF-2 # H 1.50 12 20 8 10 1.87 K 16 17 HOOD EXHAUST FAN EF-3 # H 1.50 12 20 C 10 1.87 K 18 19 HOOD CONTROLS F15 # E 0.50 12 20 A 3P 15 12 1 # : # SPARE # 20 21 IRRIGATION TIMER %& E 0.25 12 20 B 12 1 22 23 WATER HEATER CONTROLS : % & R 0.18 12 20 1 C 12 24 25 RTU-1 % % % H 7.56 4 3P 80 A 3P 15 12 # # SPARE # 26 27 H 7.56 4 B 12 28 29 H 7.56 4 C 12 FR 30 31 RTU-2 % % % % % % H 12.11 210 3P 150 A 20 12 0.18 % &; ROOF RECEPTACLE 32 33 H 12.11 B 20 12 0.50 #& :ANSUL SYSTEM 34 35 H 12.11 2/0 C 20 12 # : SPARE 36 37 H - A 20 12 1 # SPARE 38 39 H - 2/O B 20 12 1 # -SPARE 40 41 F H - C 20 12 1 I 1 # -SPARE 42 KVA PER PHASE= BUS A: 28.29 DEMAND BUS B: 34.25 KVA FACTOR DEMAND KVA BUS C: 33_68 (L) LIGHTING: 0.00 X 1.25 = 0.00 TOTAL KVA: 96.22 (R) RECEPTACLES: 0.72 X 1.00 = 0.72 (R) RECEPTACLES: 0.00 X 0.50 = 0.00 PANEL CALCULATIONS (H) HVAC: 73.53 X 1.00 = 73.53 DEMAND KVA: 88.97 (E) EQUIPMENT: 1.25 X 1.00 = 1.25 TIMES 1000 JOB NAME: (K) KITCHEN EQUIPMENT: 20.72 X 0.65 = 13.47 DIVIDED BY 1.732 Popeye's Zephyrhills (S) SUBFEED: 0.00 X 1.00 = 0.00 DMOED BY 208 MPS #: LARGEST MOTOR: 0.00 X 0.25 = 0.00 213027 TOTAL DEMAND KVA: 88.97 1 PANEL DEMAND AMPS: 246.96 DATE LAST MODIFIED 3/2112013 MANUFACTURER: SUQARE D MLO OR MCB: MLO PANEL: H TYPE: EXISTING FEED: BOTTOM VOLTAGE: 120/208V, 3 m, 4 WIRE MOUNTING: FLUSH CU ORAL WIRE: CU MAIN AMPS: 100 AMPS LOCATION: BACK WALL AICRATING: 10,000 AMPS FEEDER: 100 AMPS BREAKER OPTIONS: NOTES: # - EXISTING BREAKER NEW CIRCUIT $ - NEW BREAKER NEW CIRCUIT THIS PANEL IS FED THROUGH A CONTACTOR TO FACILITATE SHUTDOWN OF UNDER HOOD EQUIPMENT. CKT CKT NO. LOAD ;OPT CODE KVA WIRE BRKR PHASE BRKR WIRE KVA CODE OPT; LOAD NO. 1 FRYER CONTROLS A18.U6 : # E 1.00 12 20 A 20 12 1 # SPARE 2 3 HEATED HOLDING UNIT (F15.1) : $ : $ E 2.00 10 2P 30 B 20 12 1 # : SPARE 4 5 E 2.00 10 C 20 12 # SPARE 6 7 SPARE # I 12 20 A 20 1 12 1 # SPARE 8 9 SPARE # 1 12 20 B 20 12 1 # SPARE 10 11 SPACE I C 20 12 1 # 'SPARE 12 13 SPACE I A I SPACE 14 15 SPACE I B I ;SPACE 16 17 SPACE I C I ;SPACE 18 19 SPACE I A I SPACE 20 21 SPACE I B I SPACE 22 23 SPACE I C I SPACE 24 25 SPACE I A I 'SPACE 26 27 SPACE 1 B I SPACE 28 29 SPACE I C I ;SPACE 30 31 SPACE I A I ;SPACE 32 33 SPACE I B I :SPACE 34 35 SPACE I C I SPACE 36 37 SPACE I A I :SPACE 38 39 SPACE I B I SPACE 40 41 SPACE 1 C I SPACE 42 KVA PER PHASE= BUS A: 1.00 DEMAND BUS B: 2.00 KVA FACTOR DEMAND KVA BUS C: 2.& (L) LIGHTING: 0.00 X 1.25 = 0.00 TOTAL KVA: 5.00 (R) RECEPTACLES: 0.00 X 1.00 = 0.00 (R) RECEPTACLES: 0.00 X 0.50 = 0.00 PANEL CALCULATIONS (H) HVAC: 0.00 X 1.00 = 0.00 DEMAND KVA: 5.00 (E) EQUIPMENT. 5.00 X 1.00 = 5.00 TIMES 1000 JOB NAME: (K) KITCHEN EQUIPMENT: 0.00 X 0.65 = 0.00 DIVIDED BY 1.732 Papaya's Zephyrhills (S) SUBFEED: 0.00 X 1.00 = 0.00 DIVIDED BY 208 MPS #: LARGEST MOTOR: 0.00 X 0.25 = 0,00 213027 TOTAL DEMAND KVA: 5.00 PANEL DEMAND AMPS: 13.88 DATE LAST MODIFIED 3/2112013 SERVICE LOAD CALCULATION PANEL LIGHTS RECEPT. HVAC EQUIP. KITCHEN TOTALS PAN EL A 0.00 8.90 0.00 6.25 1.70 16.85 KVA PANEL B 25.60 0.00 0.00 0.25 0.00 25.85 KVA PANEL C 0.00 0.00 0.00 13.70 37.45 51.15 KVA PANEL D 0.00 0.72 73.53 1.25 20.72 96.22 KVA PANEL H 0.00 0.00 0.00 5.00 0.00 5.00 KVA TOTALS 25.60 9.62 73.53 26.45 59.87 195.07 KVA X 125% X 50% X 100% X 100% X 65% 32.00 4.81 73.53 26.45 38.92 175.71 KVA RECEPTACLE ADJUSTMENT +5.00 KVA LARGEST MOTOR 9.10 X DEMAND LOAD OF 25% PER NEC 2.28 KVA 182.98 KVA X 1000 DIVIDED BY 1.73 DIVIDED BY 208 507.92 AMPS A 800 AMP, 120/208V, 3 PHASE, 4 WIRE SERVICE HAS BEEN PROVIDED EXISTING SWITCHBOARD SCHEDULE MFR: SQUARED SHORT CIRCUIT RATING: EXISTING MAIN: MLO 800 A VOLTAGE: 120/208 PHASE: 30, 4W FEEDER NO. SERVING LOAD (KW) BREAKER WIRE CONDUIT POLES 1 PANELA 16.26 150A #1/0AWG 1.511 3 2 PANEL B 32.25 200A #3/0 AWG 2.0" 3 3 PANEL C 38.04 150A #1/0 AWG 1.511 3 4 PANEL D 88.97 400A #500 MCM 3.511 3 5 PANEL H 5.01 100A #3 AWG 1.25" 3 CONTRACTOR SHALL VERIFY THE ABOVE MINIMUM FEEDER CONDUCTOR SIZES. CONTRACTOR SHALL NOTIFY ENGINEER IF ANY OF THE ABOVE CONDUCTORS ARE FOUND TO BE SMALLER THAN THE MINIMUM SPECIFIED IN THIS MOP SCHEDULE. 101 ELECTRICAL SPECIFICAtIONS IOI EL�CTRIC,4L SYMBOLS I OI PANEL 3CHEDULEB 1 REVISIONS BY V `0 CD Y M N Q�-. O 0 ti E o _ ti v / N_a�r C U O U N cu > EE m o N !` 3 z N o ti / p :D c o1` o ba N U $1to 0:� • c •� • 6 KJ ,0 ••• OJ IVj .`- *000 .• 111 O %f__ Z fn LLJ 0 Y v O O m m V N O :E•� LLJ >. X > d W LLJ m i � N O •o m cL 4- C Date: 03. 28. 13 Scale: AS NOTED Project Mgr: EJW Drawn: CAD Job: 13-03 Sheet El