|
1 ' -- - I I I I I I I i I I I 1 1 -]I I I I 11 -
<br />DIVISION 8 DOORS AND WINDOWS (CONT.)
<br />DIVISION 8 DOORS AND WINDOWS (CONT.)
<br />DIVISION 8 DOORS AND WINDOWS (CONT.)
<br />DIVISION 9 FINISHES
<br />DIVISION 9 FINISHES CONT.
<br />I
<br />PART 2 PRODUCTS
<br />2.01 MANUFACTURERS (ACCEPTABLE MANUFACTURERS / PRODUCTS)
<br />SECTION 004113 ALUMINUM -FRAMED ENTRANCES AND STOREFRONTS
<br />SECTION 08800 GLASS 4 GLAZING
<br />SECTION 09110 METAL SYSTEMS
<br />SECTION 09900 PAMTNG .
<br />A ACCEPTABLE MANUFACTURERS: YKK AP AMERICA INC. 5630 GWALTNEY DRIVE
<br />ATLANTA, GA 30336
<br />PART I GENERAL
<br />PART I GENERAL
<br />METAL STUDS
<br />PART 1 GENERAL
<br />TELEPHONE: (404) 629-3800, FAX: (404) 629-3838
<br />I.I SUMMARY
<br />I. MEDIUM STILE SWING DOORS: YKK AP SERIES 35D MEDIUM STILE DOORS.
<br />A SECTION INCLUDES:
<br />IDI SUMMARY
<br />A AT INTERIOR METAL STUD PARTITIONS, UNLESS OTHERWISE SWM ON THE DRAWINGS PROVIDE STANDARD
<br />iDl GENERAL
<br />a. DESCRIPTION: 3-1/2" (88.S) DOOR STILE
<br />2. CORNER CONSTRUCTION: FABRICATE DOOR CORNERS JOINED BY CONCEALED REINFORCEMENT SECURED
<br />I. ALUMINUM ENTRANCE DOORS AND FRAMES.
<br />A PROVIDE AND INSTALL GLAZING AND ACCESSORIES WHERE SHOWN ON THE DRAWINGS AND AS SPEICIFIED
<br />PUNCH STEEL STUDS OF THE SIZES SHOWN ON THE DRAWINGS, EITHER HOT -DIP GALVANIZED OR FACTORY
<br />PRE -PAINT: 25 GA UNLESS SHOWN OTHERWISE ON THE DRAWINGS20 GA At ALL DOOR OPENINGS.
<br />A. IT IS THE INTENT OF THIS SPECIFICATION TO PRODUCE A PREMIUM JOB, WHICH WILL PROVIDE THE MAXIMUM
<br />WITH SCREWS, AND SIGMA DEEP PENETRATION WELDING.
<br />2. ALUMINUM FRAMED GLAZED STOREFRONTS.
<br />HEREIN. GLAZING TYPES AND SIZES SHALL BE AS PER THE DRAWINGS ANp WINDOW SCHEDULE.
<br />.
<br />B. ACCESSORIES: PROVIDE ALL ACCESSORIES INCLUDING, BUT NOT NECESSARILY LIMITED TO, TRACKS, CLIPS,
<br />DURABILITY, WHICH CAN REASONABLY BE EXPECTED FROM A PAINTED SURFACE.
<br />3. GLAZING STOPS: MANUFACTURER'S STANDARD SNAP -IN GLAZING STOPS WITH EPDM GLAZING GASKETS TO
<br />3. GLASS [WILL PANELS.
<br />4. DOOR HARDWARE.
<br />ANCHORS, FASTENING DEVICES, SOUND ATTENUATION PENCIL RODS AND RESILIENT CLIPS, AND OTHER
<br />B. "PAINT" INCLUDES COATING SYSTEMS MATERIALS, PRIMERS, EMULSIONS, ENAMELS, STAINS, SEALERS, AND
<br />PREVENT WATER INFILTRATION.
<br />B, RELATED SECTIONS:
<br />ID2 QUALITY STANDARDS
<br />ACCESSORIES REQUIRED FOR A COMPLETE AND PROPER INSTALLATION, AND AS RECOMMENDED BY THE
<br />FILLERS, AND OTHER APPLIED MATERIALS WHETHER USED AS PRIME, INTERMEDIATE, OR FINISH GOAT.
<br />4. WEATHER-STRIPPING: MANUFACTURER'S STANDARD PILE TYPE IN REPLACEABLE RABBETS FOR STILES,
<br />I. SECTION 019200 - JOINT SEALERS.
<br />A GLAZING STANDARDS: COMPLY WITH RECOMMENDATIONS FLAT GLASS MARKETING ASSOCIATION A)
<br />MANUFACTURER OF THE STEEL STUDS USED.
<br />C. SPECIFIED PRODUCTS BELOW ARE MANUFACTURED BY SHERWIN WILLIAMS, EXPECT WHERE OTHER
<br />MANUFACTURER'S STANDARD EPDM BULB TYPE IN DOOR FRAMES.
<br />2. SECTION 081100 -DOOR HARDWARE.
<br />DIC
<br />"GLAZING MANUAL" AND "SEALANT MANUAL" EXCEPT WHERE MORE STRINGENT REQUIREMENTS ARE INDICATED.
<br />E
<br />C. MEET OR EXCEED MINIMUM REQUIREMENTS OF FEDERAL SPEC. QQ-S-698 AND FEDERAL SPEC. QQ-6-115D,
<br />MANUFACTURERS ARE INDICATED, AND ESTABLISH A STANDARD OF QUALITY. EQUIVALENT PRODUCTS OF
<br />5. HARDWARE: MANUFACTURER'S STANDARD AS SELECTED BY ARCHITECT.
<br />3. SECTION 08MM - GLAZING.
<br />REFER TO THOSE PUBLICATIONS FOR DEFINITIONS OF GLASS AND GLAZING TER'1S NOT OTHERWISE DEFINED
<br />CLASS D.
<br />OTHER ACCEPTABLE MANUFACTURERS MAY NOT BE USED UNLESS APPROVED 67 ARCHITECT,
<br />MATERIALS
<br />IN THIS SECTION OR OTTER REFERENCED STANDARDS.
<br />D.PROVIDE
<br />PROVIDE BEST GRADE AND QUALITY MATERIALS AND PRODUCTS MANUFACTURED BY SHERllIN WILLIAMS.
<br />A EXTRUSIONS: ASTM B 221(A6TM B 221M), 6063-T5 ALUMINUM ALLOY.
<br />12 REFERENCES
<br />B. SAFTEY GLAZING PRODUCT: WHERE SAFTEY GLASS IS INDICATED OR REQUIRED B7 AUTHORITIES HAVING
<br />METAL TRIM
<br />MATCH COLORS AS INDICATED ON THE DRAWINGS. USE PREMIXED PAINTS INSOFAR AS POSSIBLE. THIN ONLY
<br />B. ALUMINUM SHEET:
<br />JURISDICTION, PROVIDE TYPE OF PRODUCTS INDICATED WHICH COMPLY WITH ANSI ZSTI AND TESTING
<br />A. FORE"( FROM GALVANIZED STEEL NOT LIGHTER THAN 2(6 GAUGE, COMPLYING WITH FEDERAL SPEC QQ-5-115,
<br />AS PERMITTED ANY MANUFACTURER'S LABEL INSTRUCTIONS, AND AVOID UNNECESSARY THINNING.
<br />I. ANODIZED FINISH: ASTM B 209 (ASTM 8 209M), 5005-H14 ALUMINUM ALLOY, 0D50 INCH (121mm) MINIMUM
<br />A AMERICAN ARCHITECTURAL MANUFACTUI�RS ASSOCIATION (AAMA) lIUIEW.AAMANET.ORG):
<br />REQUIREMENTS OF CPSC 16 CFR PART 1201 FOR CATEGORY 11 MATERIALS.
<br />CLASS D.
<br />E. PROTECT FINISHED SURFACES, WORK OF OTHER TRADES, AND PROPERTY OF THE OWNER FROM DAMAGE AND
<br />THICKNESS.
<br />I. 611 - VOLUNTARY SPECIFICATION FOR ANODIZED ARCHITECTURAL ALUMINUM.
<br />C. FIRE -RESISTANCE -RATED WIRE GLASS: PROVIDE WIRE GLASS PRODUCTS THAT ARE IDENTICAL TO THOSE
<br />B, CASING BEADS: US.G.'200-5.
<br />DEFACEMENT. COVER FLOORS AND FIXED EQUIPMENT WITH DROP CLOTHS.
<br />2.03 ACCESSORIES
<br />TESTED PER ASTM E 163 (UL S) AND ARE LABELED AND LISTED BY UL OR OTHER TESTING AND INSPECTING
<br />F. PREPARE SURFACES ACCORDING TO PAINT MANUFACTURER'S INSTRUCTIONS. EXAMINE FACTORY FINISHED AND
<br />A. MANUFACTURER'S STANDARD ACCESSORIES:
<br />B. ASTM INTERNATIONAL (ASTM) (WWW.ASTM.ORGJ
<br />AGENCY ACCEPTABLE TO AUTHORITIES HAVING JURISDICATION.
<br />END OF SECTION 09110 I
<br />PRIMED SURFACES TO BE PAINTED, AND VERIFY COMPATIBILITY OF EXISTING MATERIAL WITH PAINT TO BE
<br />I. FASTENERS: ZINC PLATED STEEL CONCEALED FASTENERS, HARDENED ALUMINUM ALLOYS OR AISI 300
<br />I. E283 - STANDARD TEST METHOD FOR RATE OF AIR LEAKAGE THROUGH EXTERIOR WINDOWS,
<br />D. SINGLE SOURCE RESPON5I5ILT7 : PROVIDE MATERIALS OBTAINED FROM ONE SOURCE FOR EACH TYPE OF
<br />SECTION 09Z50 GYPSI,�'1 WALLBOARD
<br />APPLIED. APPLY PAINT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS ONLY
<br />SERIES STAINLESS EXPOSED FASTENERS, COUNTERSUNK, FINISH TO MATCH ALUMINUM COLOR
<br />CURTAIN WALLS AND DOORS.
<br />GLAZING PRODUCT IDICATED.
<br />TO SURFACES WHICH ARE THOROUGHLY DRY, SMOOTH, EVEN, CLEAN, FREE OF DUST AND PROPERLY
<br />2. SEALANT. NON -SKINNING TYPE, AAMA 8033.
<br />2. E330 - STANDARD TEST METHOD FOR STRUCTURAL PERFORMANCE OF EXTERIOR WINDOWS, CURTAIN
<br />E. PROVIDE GLASS AND GLAZING THAT HAS BEEN PRODUCED, FABRICATED AND INSTALLED TO WITHSTAND
<br />PART I GENERAL
<br />PREPARED TO RECEIVE THE INTENDED FINISH.
<br />3. GLAZING: SETTING BLOCKS, EDGE BLOCKS, AND SPACERS IN ACCORDANCE WITH A5TM C 864, SHORE
<br />WALLS, AND DOORS UNDER THE INFLUENCE OF WIND LOADS.
<br />NORMAL TEMPERATURE CHANGES, WIND LOADING, IMPACT LOADING, WITHOUT FAILURE INCLUDING LOSS OR
<br />1.02 PAINTING
<br />DUROMETER HARDNESS AS RECOMMEND BY MANUFACTURER, GLAZING GASKETS IN ACCORDANCE
<br />3. E331 - STANDARD TEST METHOD FOR WATER PENETRATION OF EXTERIOR WINDOWS, DOORS, AND
<br />BREAKAGE OF GLASS, FAILURE OF SEALMENTS OR GASKETS TO REMAIN WATERTIGHT AND AIRTIGHT,
<br />IOl
<br />A ACCEPTABLE MATERIALS
<br />WITH ASTM C 864.
<br />CURTAIN WALLS BY UNIFORM STATIC AIR PRESSURE DIFFERENTIAL.
<br />DETERIORATION OF GLASS AND GLAZING MATERIALS, AND OTHER DEFECTS IN THE WORK
<br />A. GYPSUM WALLBOARD WORK SHALL CONFORMTO THE GYPSUM ASSOCIATION "RECOMMENDED
<br />I. ALL PAINTING To BE SCHEDULED IN THE FINISH SCHEDULE.
<br />2. EQUIVALENT PRODUCTS OF THE FOLLOWING AIRE ALSO ACCEPTABLE:
<br />2.04 FABRICATION.
<br />F. FIELD MEASURE ALL OPENINS OR AREAS TO RECEIVE GLASS AND GLAZING TO ASCERTAIN CORRECT FIT,
<br />SPECIFICATIONS FOR THE APPLICATION AND FINISHING OF GYPSUM WALLBOARD."
<br />PRATT 4 LANBERTT
<br />13 SYSTEM DESCRIPTION
<br />IMPROPERLY SIZED GLASS OR GLAZING SHALL BE REPLACED AT NO ADDITIONAL COST TO OWNER
<br />A SHOP ASSEMBLY: FABRICATE AND ASSEMBLE UNITS WITH JOINTS ONLY AT INTERSECTION OF ALUMINUM
<br />GLIDDEN
<br />MEMBERS WITH UNIFORM HAIRLINE JOINTS, RIGIDLY SECURE, AND SEALED IN ACCORDANCE WITH
<br />A DESIGN REQUIREMENTS: DESIGN EXTERIOR SYSTEMS TO WITHSTAND:
<br />1.03 SUBMITALS
<br />B. EXAMINE SUBSTRATES TO WHICH DRY WALL CONSTRUCTION ATTACHES OR ABUTTS, PRESET HOLLOW METAL
<br />PORTER
<br />MANUFACTURER'S RECOMMENDATIONS.
<br />I. DESIGN WIND PRESSURE IN ACCORDANCE WITH ASGE 1, BUILDING C.OpE, TESTED IN ACCORDANCE
<br />A PRODUCT DATA: SUBMIT MANUFACTURER'S TECHNICAL DATA FOR EACH GLAZING MATERIAL, FABRICATED
<br />FRAMES, CAST-IN-ANCORS, AND STRUCTURAL FRAMING FOR COMPLIANCE WITH REQUIREMENTS FOR
<br />BENJAMINE MOORE
<br />1. HARDWARE: DRILL AND CUT TEMPLATE FOR HARDWARE. REINFORCE FRAMES AND DOOR STILES TO
<br />WITH ASTM E330.
<br />GLASS PRODUCT REQUIRED AND SEALANT INCLUDED INSTALLATION AND MAINTENANCE INSTRUCTIONS,
<br />INSTALLATION TOLERANCE AND OTHER CONDITIONS AFFECTING PERFORMANCE OF DRYWALL
<br />CONSTRUCTION. DO NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY COND TIONS HAVE BEEN
<br />B. UNDERCOATS AND THINNERS
<br />RECEIVE HARDWARE IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS.
<br />2. MOVEMENT CAUSED BY AN AMBIENT TEMPERATURE RANGE OF 120 DEGREES F AND A SURFACE
<br />PERFORMANCE CRITERIA, ETC_
<br />I. PROVIDE UNDERCOAT PAINT PRODUCED BY THE SAME MANUFACTURER OF FINISH COAT.
<br />2. WELDING: CONCEAL WELDS ON ALUMINUM MEMBERS IN ACCORDANCE WITH AWS RECOMMENDATIONS OR
<br />TEMPERATURE RANGE OF 160 DEGREES F.
<br />B. SAMPLES: SUBMIT, FOR VERIFICATION PURPOSES, 12" SQUARE SAMPLE OF EACH TYPE OF GLASS
<br />CORRECTED.
<br />1. USE ONLY THINNERS RECOMMENDED BY THE PAINT MANUFACTURER 4 USE ONLY THE RECOMMENDED LIMITS.
<br />METHODS RECOMMENDED BY MANUFACTURER MEMBERS SHOWING WELDING BLOOM OR DISCOLORATION ON
<br />INDICATED, INCLUDING MIRRORS, MOUNTING HARDWARE AND MATERIALS.
<br />C. DO NOT TAPE AND FINISH GYPSUM BOARD WHEN THE TEMPERATURE IS BELOW 60 D=GREE5 FAHRENHEIT.
<br />C. COLOR SCHEDULES
<br />FINISH OR MATERIAL DISTORTION WILL BE REJECTED.
<br />B. PERFORMANCE REQUIREMENTS:
<br />C. CERTIFICATE: SUBMIT CERTIFICATES FROM RESPECTIVE MANUFAGTURIERS ATTESTING THAT GLASS AND
<br />THE TEMPERATURE OF THE ROOMS SHALL BE HELD AT 60 DEGREES FAHRENHEIT FCR 48 HOURS BEFORE
<br />1. PROVIDE PAINTING AS SCHEDULED IN THE FINISH MATERIALS SCHEDULE.
<br />B. FABRICATION TOLERANCES:
<br />I. AIR INFILTRATION, TESTED TO ASTM E283.
<br />GLAZING MATERIALS FURNUSHED FOR PROJECT COMPANY WITH REQUIREMENTS, INCLUDE ALL REQUIRED
<br />TAPING AND FINISHING IS TO BEGIN. MAINTAIN 60 DEGREES FAHRENHEIT DURING AND AFTER INSTALLATION.
<br />a. ON GYPSUM DRYWALL, USE:
<br />I. MATERIAL CUTS: SQUARE TO 1/32 INCH (0.8mm) OFF SQUARE, MAXIMUM, OVER LARGEST DIMENSION,
<br />a. ENTRANCES:
<br />WARRANTIES.
<br />VENTILATES AS REQUIRED TO REMOVE EXCESS HUMIDITY.
<br />1. FIRST COAT - PIGMENTED PRIMER/SEALER
<br />PROPORTIONATE AMOUNT OF 1/32 INCH (O.Smm) ON OTHER TWO DIMENSIONS.
<br />1) SINGLE DOOR: MAXIMUM 05 CFM PER MINUTE PER LINEAR FOOT OF PERIMETER CRACK, AT
<br />I. GLASS MANUFACTURER SHALL SUBMIT A CERTIFIED LETTER STATING THAT ALL GLASS SIZE AND
<br />.
<br />2. SECOND COAT - ACRYLIC LATEX ENAMEL
<br />2. MAXIMUM OFFSET: 1/64 INCH (0.4mm) IN ALIGNMENT BETWEEN TWO CONSECUTIVE MEMBERS IN LINE,
<br />STATIC PRESSURE DIFFERENTIAL OF 624 PSF.
<br />THICKNESS FOR ALL GLAZING OPENINGS MEET OR EXCEED THE WIND LOAD REQUIREMENTS AS
<br />102 GYPSUM WALLBOARD
<br />3. THIRD COAT - ACRYLIC LATEX ENAMEL
<br />END TO END.
<br />b. STOREFRONT: 0.06 CFM PER SQUARE FOOT OF FIXED AREA AT STATIC PRESSURE DIFFERENTIAL
<br />SPECIFIED IN SECTION 08410, ALUMINUM ENTRANCES AND STORFRONTS, AND SECTION 08521,
<br />A GYPSUM WALLBOARD SHALL BE MANUFACTURED BY U.S. GYPSUM. WALLBOARD IS TO MEET. ASTM G36-84A
<br />b. ON FERROUS METAL, USE:
<br />3. MAXIMUM OFFSET. 1/64 INCH (0.4mm) BETWEEN FRAMING MEMBERS AT GLAZING POCKET CORNERS.
<br />OF 624 PSF.
<br />ALUMINUM WINDOWS.
<br />AND 55-L-30d 1/2 INCHES THICK, 48 INCHES WIDE WITH TAPERED EDGES.
<br />I. FIRST COAT - RUST INHIBITIVE ALKYD METAL PRIMER
<br />4. JOINTS (BETWEEN ADJACENT MEMBERS IN SAME ASSEMBLYb HAIRLINE AND SQUARE TO ADJACENT
<br />2. WATER INFILTRATION: NO UNCONTROLLED WATER LEAKAGE, TESTED TO ASTM E331 At MINIMUM TEST
<br />B. AT FIFE RATED PARTITIONS INSTALL WALLBOARD TO MEET SEPARATE REQUIREMENTS, USE TYPE III, GRADE
<br />2. SECOND COAT - SEMI -GLOSS ALKYD ENAMEL
<br />MEMBER
<br />PRESSURE OF 624 PSF FOR INSWING DOORS AND 8.0 F'SF FOR OUTSWING DOORS AND STOREFRONT.
<br />ID4 DELIVERY, STORAGE AND HANDLING
<br />X CLASS 1, 5/5 INCHES THICK FIFE RETARDANT WALLBOARD.
<br />3. THIRD COAT - SEMI -GLOSS ALKYD ENAMEL
<br />5. VARIATION (IN SQUARING DIAGONALS FOR DOORS AND FABRICATED ASSEMBLIES): I/I6 INCH (Ibmm).
<br />3. UNIFORM STRUCTURAL LOADING: NO GLASS BREAKAGE OR PEWANENT DAMAGE TO FASTENERS OR
<br />A. PROTECT GLASS AND GLAZING MATERIALS DURING DELIVERY, STORAGE AND HANDLING TO COMPLY WITH
<br />C. INSTALL GYPSUM BOARD WITH TRUE, EVEN SURFACES AND STRAIGHT, SHARP CORNERS.'USE FULL LENGTH
<br />c. ON WOOD DOORS, USE:
<br />(b. FLATNESS (FOR DOORS AND FABRICATED ASSEMBLIES} t 1/16 INCH (Ibmm) OFF NEUTRAL PLANE.
<br />SYSTEM COMPONENTS, TESTED TO ASTM E330 At 15 TIMES DESIGN PRESSURE.
<br />4. THEWAL TRANSMITTANCE DUE TO CONDUCTION RUC}. MAXIMUM 0b0, TESTED TO AAMA 1503 ON TWO
<br />T E
<br />MANUFACTURER'S DIRECTIONS AND AS REQUIRED TO PREVENT EDGE DAMAGE TO GLASS AND GLAZING
<br />BOARDS WHERE POSSIBLE. ENE) JOINTS ON THE SAME SIDE OF A WALL SHALL BE STAGGERED AND JOINTS
<br />I. FIRST COAL -STAIN (SEE FINISH SCHEDULE)
<br />2,05 FINISHES AND COLORS
<br />X 6 -0 UNITS WITH I INCH ,CLEAR INSULATING GLASS.
<br />MATERIALS FROM EFFECTS OF MOISTURE INCLUDING CONDENSATION, OF TEMPERATURE CHANGES, OF DIRECT
<br />ON OPPOSITE SIDE SHALL NOT OCCUR OVER THE SAME SUPPORT. DO NOT LOCATE NORMAL END JOINTS AT
<br />EDGE OF OPENINGS. FORM JOINTS NEATLY. BUTT BOARDS TOGETHER BUT DO NOT FORCE INTO PLACE. DO
<br />2, SECOND COAT - STAIN (SEE FINISH SCHEDULE)
<br />"RUBBED
<br />A. ANODIZED FINISH: YKK AP AMERICA ANODIZED FINISH:
<br />5. CONDENSATION RESISTANCE FACTOR (CRFk MINIMUM 50, TESTED TO AAMA 1503.
<br />EXPOSURE TO SUN, AND FROM OTHER CAUSES.
<br />NOT BUTT EDGES AGAINST TAPERED EDGES. NO JOINT SHALL HAVE A GAP GREATER THAN 1/4 INCH.
<br />3. THIRD COAT - VARNISH LOW SHEEN EFFECT"
<br />I. CLEAR YKK AP YSN WITH CLEAR PROTECTIVE COMPOSITE COATING.
<br />B. STORE IN LOCATION TO PREVENT ANY DAMAGE. REPLACE GLASS OR GLAZING MATERIALS AT ANY POINT
<br />D. IN GENERAL, INSTALL GYPSUM BOARD ON CEILING BEFORE WALLS. CONSTRUCT CEILINGS WITH LONG
<br />END OF SECTION 09900
<br />B. FINISHING PREPARE ALUMINUM SURFACES FOR SPECIFIED FINISH, APPLY FINISH IN ACCORDANCE WITH THE
<br />1.4 SUBMITTALS
<br />DURING THE CONTRACT PERIOD AT NO COST TO OWNER
<br />FOLLOWING:
<br />DIMENSION OF GYPSUM BOARD APPLIED AT RIGHT ANGLES TO SUPPORT.
<br />SECTION 09960 STUCCO FINISH .
<br />I. ANODIZED COATING: ELECTROLYTIC COLOR COATING FOLLOWED BY AN ORGANIC TOP COATING APPLIED
<br />A. SUBMITTALS FOR REVIEW:
<br />ID5 GUARANTEE
<br />E. SCREW GYPSUM BOARD TO FRAMING WITH SCREWS NOT OVER 8 INCHES ON CENTER FASTEN GYPSUM
<br />TO ALUMINUM EXTRUSIONS PRODUCED FROM QUALITY CONTROLLED BILLETS MEETING AA-6063-T5.
<br />I. SHOP DRAWINGS: INDICATE SYSTEM DIMENSIONS, FRAMED OPENING REQUIREMENTS AND
<br />A PROVIDE MINIMUM TEN (10) YEAR GUARANTEE FOR ALL GLASS PRODUCTS, INCLUDING GUARANTEE AGAINST
<br />BOARD BEGINNING AT THE CENTER AND WORK TOWARDS OUTER EDGES. HOLD BOARD FIWLY AGAINST
<br />WOOD FRAMING WHILE FASTENING. FASTENERS AT EDGES OF BOARDS SHALL BE 1/2 INCH FROM THE EDGE.
<br />PART I GENERAL
<br />a. EXPOSED SURFACES SHALL BE FREE OF SCRATCHES AND OTHER SERIOUS BLEMISHES.
<br />TOLERANCES, TRIM, SEALERS, HARDWARE, AND ACCESSORIES.
<br />SILVER SPOILAGE OF ALL MIRRORS, PESFOR'(ANCE OF GLAZING SEALANTS, TEC.
<br />IDI SUMMARY
<br />b. EXTRUSION SHALL BE GIVEN A CAUSTIC ETCH FOLLOWED BY AN ANODIC OXIDE TREATMENT AND SEALED
<br />F. OPENINGS FOR ELECTRICAL DEVICES, PIPING, GRILLS, AND REGISTERS SHALL BE ACCURATELY LOCATED
<br />A MATERIALS AND INSTALLATION OF CEMENT STUCCO ON HOLLOW MASONRY, EXTERIOR GRADE PLYWOOD AND
<br />WITH AN ORGANIC ELECTRODEPOSITION APPLIED PROTECTIVE TOP COATING.
<br />B. SUSTAINABLE DESIGN SUBMITTALS:
<br />PART 2 PRODUCTS
<br />AND NEATLY MADE TO CLOSELY FIT THE DEVICES AND BE COMPLETELY COVERED BY PLATES AND
<br />METAL LATH ALSO FURNISH AND INSTALL METAL, LATH, STUCCO WRAP AND ACCESSORIES.
<br />c. OVERALL COATING THICKNESS FOR FINISHES SHALL BE A MINIMUM OF 0.1 MILS.
<br />I. RECYCLED CONTENT.
<br />ESCUTCHEONS.
<br />d. COATING SHALL GONFOR'1 TO ALUMINUM ASSOCIATION STANDARD AAMI2C22A4X. A4X DESIGNATION SHALL
<br />2. REGIONAL MATERIALS.
<br />201 GLASS
<br />ID3 TRIM PIECES
<br />1.02 DELIVERY, STORAGE AND HANDLING
<br />SIGNIFY AN ANODIC COATING OF 0.4 MILS MINIMUM FOLLOWED BY AN ORGANIC TOP COATING OF A
<br />A PROVIDE GLASS TYPES AND THICKNESS AS PER DRAWINGS AND WINDOW SHCEDULE:
<br />A PROVIDE TRIM ACCESSORIES OF THE SIZES REQUIRED FOR THE WALLBOARD APPLICATION AS
<br />A. DELIVER ALL CEMENT MATERIALS IN ORIGINAL CONTAINERS BEARING MANUFACTURERS NAME AND
<br />MINIMUM 03 MILS.
<br />PART 2PRODUCTS
<br />FLOAT (OR "PLATE" h COMPLY WITH FEDERAL SPECIFICATION DD-G-451,
<br />MANUFACTURED BY U.S. GYPSUM. PROVIDE DUR-A-BEAD CORNER BEAD AT EXTERNAL CORNERS AND NO.
<br />IDENTIFICATION.
<br />INJADDITION TO THE ALUMINUM ASSOCIATION STANDARD ABOVE, FINISH SHALL CONFORM TO THE FOLLOWING:
<br />CLEAR WIRE GLASS: COMPLY WITH FEDERAL SPECIFICATION DD-G-451.
<br />200-A METAL CASING BEAD WHERE WALLBOARD ABUTTS OTHER MATERIALS.
<br />B. DELIVER NEW, FLAT STRUCTURAL METAL. LATH IN ORDINAL PACKAGING.
<br />U AAMA 6052 MORTAR RESISTANCE TEST SPECIFICATION, TEST METHOD PER ASTM C201, 24 HOUR
<br />2.1 MANUFACTURERS
<br />FIGURED AND PATTERN GLASS: COMPLY WITH FEDERAL SPECIFICATION DD-G-451.
<br />C. PROTECT PRODUCTS FROM MOISTURE AND HUMIDITY. STORE UNDER COVER OFF GROUND IN A DRY
<br />PAT TEST.
<br />2) CASS CORROSION RESISTANCE TEST. CASS 240/ ASTM 53" TEST METHOD.
<br />A ACCEPTABLE MANUFACTURERS:
<br />B. SUBJECT TO COMPLIANCE WITH ALL REQUIREMENTS, THE FOLLOWING MANUFAGTUERERS OFFER PRODUCT WHICH
<br />1.04 FASTENERS
<br />LOCATION.
<br />OTHER AAMA 6052 PERFORMANCE TESTS SPECIFIED IN THESE SPECIFICATIONS, SUCH AS: 13 DRY FILM
<br />I. UNITED STATES ALUMINUM
<br />MAY BE INCORPOATED IN THE WORK.
<br />1. TINTED GLASS:
<br />A PROVIDE SCREWS, NAILS, CLIPS, TIES, AND OTHER FASTENERS AS RECOMMENDED BY THE GYPSUM
<br />103 SUBMITTALS
<br />3) HARDNESS,1.6.2 SALT SPRAY RESISTANCE,1.9.12 COLOR RETENTION, SOUTH FLORIDA,134.14 GLOSS
<br />2. YKK AP AMERICA, INC. (WWW.YKKAP.COM)
<br />a. PPG-INDUSTIES, INC. 5OLAR3RAY COMMERCIAL INSULATING GLASS I -INCH UNITS WITH 1/2-INCH AIRSPACE
<br />MANFACTURRR
<br />A MANUFACTURERS SPECIFICATION AND PRODUCT DATA FOR STUCCO APPLICATIONS.
<br />RETENTION, SOUTH FLORIDA,
<br />22 MATERIALS
<br />AND 1/4-INCH LINES, INTERIOR LITE CLEAR
<br />B. STUCCO WRAP STRUCTURAL METAL LATH AND ACCESSORIES, SUCH AS CORNER BEAD, CONTROL JOINTS, ETC.
<br />G. HIGH PERFORMANCE ORGANIC COATING FINISH:
<br />2. WIRE GLASS:
<br />ID5 JOINT TREATMENT SYSTEMS
<br />PART 2 PRODUCTS
<br />I. TYPE FACTORY APPLIED TWO -COAT 109. KYNAR RESIN BY AUTO C4EM OR 10q HYLAR RESIN BY AUSIMONT,
<br />a FIRELITE
<br />A SYSTEM SHALL BE PERFORATED TAPE AND CEMENT RECOMMENDED THE GYPSUM MANUFACTURER
<br />FLOUROPOLYMER BASED COATING SYSTEM, POLYVINLYIDENE FLUORIDE (PVF-2). APPLIED IN ACCORDANCE
<br />A ALUMINUM:
<br />I. EXTRUSIONS: ASTM B221, 6063-15 ALLOY AND TEMPER
<br />3. CLEAR FLOAT GLASS:
<br />B. APPLY MATERIALS IN STRICT ACCORDANCE TO MANUFACTURER'S RECOMMENDATIONS. FILL JOINTS WITH
<br />201 JOB MIXED INGREDIENTS
<br />WITH YKK AP PROCEDURES AND MEETING AAMA 6052 SPECIFICATIONS.
<br />2. SHEET: ASTM 8209, ALLOY AND TEMPER BEST SUITED TO APPLICATION.
<br />a. PPG INDUSTRIES, INC.
<br />JOINT COMPOUND, EMBED PEI;�FORATED TAPE ANI) APPLY A SKIM COAT OF JOINT COMPOUND OVER TAPE.
<br />A PORTLAND CEMENT, ASTMC 150 TYPE 1, MIXED IN ACCORD WITH MANUFACTURERS INSTRUCTIONS.
<br />2. COLORS: SELECTEE) BY ARCHITECT FROM THE FOLLOWING:
<br />3. RECYCLED CONTENT: MINIMUM PERCENT, WITH MINIMUM PERCENT CLASSIFIED AS POST -CONSUMER
<br />b. FORD GLASS DIVISION.
<br />APPLY TWO ADDITIONAL COATS OF JOINT COMPOUND ALLOWING AT LEAST 24 HOURS BETWEEN EACH COAT.
<br />B. WATER, CLEAN AND POTABLE.
<br />a. STANDARD COATING COLOR CHARTS.
<br />AS SHOWN ON DRAWINGS.
<br />c. LIBBEY-OWENS-FORD CO.
<br />SAND EACH COAT. FINISH SURFACES SHALL BE UNIFORMLY SMOOTH, TRUE AND IN SATISFACTORY CONDITION
<br />C. METAL LATH
<br />I,
<br />1. STRUCTURAL METAL LATH SHALL BE 3.4 POUND EXPANDED METAL SHEET WITH SOLID PARALLEL RIBS.
<br />c. COLOR NAME AND NUMBER
<br />23 COMPONENTS
<br />MAY BE APPROVED WITH COMPLETE DATA SUBMITTAL AND ARCHITECT APPROVAL PRIOR TO BIDDING IN
<br />2. METAL LATH SHALL BE 3A POUND DIAMOND MESH METAL LATH.
<br />D. FINISHES TESTING:
<br />ACCORDANCE WITH DIVISION I.
<br />END OF SECTION 09250
<br />3. ACCESSORIES FURNISHED BY SAME MANUFACTURER FOR STUCCO APPLICATION.
<br />I. APPLY 0.5% SOLUTION NaOH, SODIUM HYDROXIDE, TO SMALL AREA OF FINISHED SAMPLE AREA, LEAVE IN
<br />A, ENTRANCES DOORS: NARROW STILE CONFIGURATION WITH NOMINAL 2 INCH VERTICAL STILES AND TOP
<br />D. INSULATING GLASS: COMPLY WITH ASTM E-113, ASTM E-114. SEALED INSULATING UNITS FABRICATED FROM TWO
<br />D. MECHANICAL FASTENERS
<br />PLACE FOR SIXTY MINUTES, LIGHTLY WIPE OFF NaOH, DO NOT CLEAN AREA FURTHER
<br />RAIL AND 10 INCH BOTTOM RAIL.
<br />PANES OF GLASS WITH AIR SPACE BETWEEN. GLASS THICKNESS AND HEAT STRENGTHENING TO BE DETERMINED
<br />SECTION 09300 CERAMIC TILE
<br />1. NAILS, 8d RING SHANK, HOT DIP GALVANIZED OF SUFFICIENT LENGHTH TO PENETRATE PLYWOOD BACKING
<br />SUBMIT SAMPLES WITH TEST AREA NOTED ON EACH SAMPLE.
<br />BY MANUFACTURER FOR WINE) LOADING CONDITION. INSULATING GLASS WARRANTY: 10 YEARS.
<br />I INCH.
<br />B. STOREFRONT: FLUSH GLAZING SYSTEM DESIGNED TO RECEIVE 1 INCH GLASS BY MEANS OF
<br />PART I GENERAL
<br />2. WHERE LIGHT METAL FRAMING OCCURS: MINIMUM NOB SELF DRILLING CORROSION RESISTANT SCREWS OF
<br />PART 3 EXECUTION
<br />ELASTOMERIC GASKETSt 2 INCH FACE WIDTH X 4-1/2 INCH DEPTH, CENTER GLASS APPLICATION,
<br />2D2 MANUFACTURERS / PRODUCTS
<br />-
<br />SUFFICIENT LENGTH TO PENTRATE METAL 3/8 INCH.
<br />THERMALLY BROKEN.
<br />A FLOAT GLASS (TYPE FG-Ak CLEAR 1/4 INCH THICK, MINIMUM.
<br />IDI GENERAL
<br />E. STUCCO WRAP
<br />3DI MANUFACTURERS INSTRUCTIONS / RECOMMENDATIONS
<br />SAFTEY GLASS (TYPE FG-Eh CLEAR, FULLY TEMPERED 1/4 INCH THICK, MINIMUM.
<br />A CERAMIC AND TYPES ARE INDICATED ON THE DRAWINGS AND ARE FROM A SINGLE MANUFACTURER OTHER
<br />1. BY "TYVEK" FOR USE OVER PLYWOOD FACINGS.
<br />A COMPLIANCE: COMPLY WITH MANUFACTURER'S PRODUCT DATA, INCLUDING PRODUCT TECHNICAL BULLETINS,
<br />C. DOOR HARDWARE: SPECIFIED IN SECTION 081100.
<br />LOW E GLASS (TYPE FG-Fk FLOAT TYPE, TEMPERED, CLEAR COATING ON INNER SURFACE.
<br />MANUFACTURERS WILL NOT BE CONSIDERED.
<br />F. STUCCO ACCESSORY TRIM, BEADS, AND CONTROL JOINTS SHALL BE VINYL.
<br />PRODUCT CATALOG INSTALLATION INSTRUCTIONS, AND PRODUCT CARTON INSTRUCTIONS.
<br />MIRROR GLASS (TYPE FG-Hk CLEAR TEMPERED SAFTEY TYPE WITH COPPER AND SILVER COATING, SQUARE
<br />B. DELIVER MATERIALS IN ORIGINAL CONTAINERS WITH SEALS UNBROKEN AND LABELS INTACT UNTIL TIME OF
<br />2.4 ACCESSORIES
<br />EDGES,
<br />USES. ENGAGE AN EXPERIENCED INSTALLER WHO HAS SUCCESSFULLY COMPLETED TILE INSTALLATIONS
<br />PART 3 EXECUTION
<br />3D2 EXAMINATION
<br />A. SITE VERIFICATION CONDITIONS: VERIFY CONDITIONS INSTALLED RENDER
<br />HAVE BEEN PREVIOUSLYDANCE
<br />A FASTENERS:
<br />SIMILAR IN MATERIAL, DESIGN, AND EXTENT TO THAT INDICATED FOR THE PROJECT.
<br />3.01 INSTALLATION
<br />INSTAWHICHLLATION WITH
<br />OTHER SECTIONS) ARE ACCEPTABLE FOR PRODUCT INSTALLATION IN ACCORDANCE WITH MANUFACTURER'S
<br />R
<br />I. SERIES 300 STAINLESS STEEL FOR WET LOCATIONS AND EXPOSED FASTENERS.
<br />PARE' 3 EXECUTION
<br />C. COMPLY WITH PARTS OF ANSI 108 SERIES OF FINE INSTALLATION STANDARDS INCLUDED UNDER "AMERICAN
<br />A INSTALL MECHANICAL FASTENERS ON 6 INCH CENTERS ALONG SEAMS AND 12 INCH CENTERS ALONG
<br />INSTRUCTIONS.
<br />1. STAINLESS OR FLUOROPOLYMER COATED STEEL FOR OTHER LOCATIONS.
<br />NATIONAL STANDARD SPECIFICATIONS FOR THE INSTALLER OF CERAMIC TILE" THAT APPLY t0 TYPE OF
<br />INTERIORS.
<br />I. VERIFY LOCATION OF PRESET ANCHORS, PERIMETER FASTENERS, AND BLOCK -OUTS ARE IN ACCORDANCE
<br />3DI PRECONSTRUGTION
<br />SETTING AND GROUT MATERIALS AND METHODS INDICATED. TILE MAY BE THIN -SET.
<br />B. STUCCO INSTALLATION SHALL BE TWO COAT APPLICATION. APPLY BASE COAT WITH FIRM PRESSURE TO
<br />WITH SHOP DRAWINGS,
<br />B. JOINT SEALERS: SPECIFIED IN SECTION 019200.
<br />A EXAMINE JOB CONDITIONS AND VERIFY THAT ALL ARE SATISFACTORY FOR SPEEDY AND ACCEPTABLE WORK
<br />FORM GOOD BOND THEN DOUBLE BACK TO PROVIDE THICKNESS. LEAVE ROUGH ENOUGH TO PROVIDE BOND
<br />B. CLEAN AND PREPARE GLAZING SUPPORT MATERIALS ACCORDING TO MANUFACTURER'S INSTRUCTIONS AND
<br />1.02 MORTAR AND GROUT
<br />FOR FINISH COAT. FINISH COAT SHALL BE OF TEXTURE AS CALLED FOR ON THE BUILDING ELEVATION
<br />3.03 PREPARATION
<br />C. GLASS AND GLAZING ACCESSORIES: SPECIFIED IN SECTION 088000.
<br />STANDARDS OF THE GLASS ASSOCIATION OF NORTH AMERICA GLAZING MANUAL.
<br />A. MORTAR SHALL BE PORTLAND CEMENT ASTM C150, TYPE 1. GROUT SHALL BE ACID RESISTANT UPCO
<br />DRAWINGS.
<br />A ADJACENT SURFACES PROTECTION: PROTECT ADJACENT WORK AREAS AND FINISH SURFACES FROM DAMAGE
<br />C. INSPECTION AND CLEANING SHALL INCLUDE BUT IS NOT LIMITED TO THE FOLLOWING: CLEAN DIRT OR
<br />HYDROMENT, TYPE AS RECOMMENDED BY THE MANUFACTURER FOR THE SPECIFIC TYPE OF TILE AND
<br />C. CURING: CURE STUCCO BY USE OF POLYETHYLENE FILM, OR BY USE OF FINE SPRAY.
<br />DURING PRODUCT INSTALLATION.
<br />D. WEATHERSTRIPPING: REPLACEABLE, NONPOROUS SYNTHETIC WOOL PILE TYPE.
<br />FOREIGN MATERIALS FROM CHANNELS, STOPS, RABBETS, SETTING BLOCKS, SPACERS, ECT_ REMOVE NOW
<br />METHOD OF INSTALLATION. COLR FOR FLOOR TILE IS SPECIFIED ON THE DRAWINGS.
<br />I. ALUMINUM SURFACE PROTECTION: PROTECT ALUMINUM SURFACES FROM CONTACT WITH LIME, MORTAR,
<br />PERMANENT PROTECTIVE COATINGS. WIPE SURFACES CLEAN IMMEDIATELY PRIOR TO ADDING PRIMER, TAPES
<br />B. DO NOT GROUT TILE UNTIL TILE IS FIRMLY SET. SOAK OR DAMPEN JOINTS OF THE TILE TO BE GROUTED WITH
<br />3.02 PROTECTION
<br />CEMENT, ACIDS, AND OTHER HARMFUL CONTAMINANTS.
<br />25 FABRICATION
<br />OR GLAZING COMPOUNDS. APPLY PRIMER TO SURFACES AS REQUIRED TO RECEIVE GLAZING COMPOUNDS.
<br />PORTLAND CEMENT GROUT. SOAK OR DAMPEN OTHER JOINTS AS RECOMMENDED BY THE GROUT
<br />A. PROTECT STUCCO DURING AND UPON COMPLETION FROM WATER INFILTRATION, DUST, DIRT, PRECIPITATION,
<br />MANUFACTURER FORCE GROUT INTO JOINT LINES COMPLETELY IDILING JOINTS WITH COMPACTED GROUT AND
<br />EXCESSIVE DRYING UNTIL STUCCO HAS SET,
<br />3.04 INSTALLATION
<br />A FABRICATE WITH MINIMAL CLEARANCES AND SHIM SPACES AROUND PERIMETER
<br />3.02 INSTALLATION
<br />COVERING MORTAR FINISH JOINTS OF SQUARE EDGED TILE FLUSH WITH SURFACE. STRIKE OFF TOOL JOINTS
<br />END OF SECTION 09960
<br />A. GENERAL: INSTALL MANUFACTURER'S SYSTEM IN ACCORDANCE WITH SHOP DRAWINGS, AND WITHIN SPECIFIED
<br />A INSPECT FRAMING BEFORE INSTALLATION AND PROVIDE WRITTEN REPORT OF ANY CONDITIONS THAT MIGHT
<br />OF CUSHION EDGED TILE TO DEPTH OF CUSHION. FILL GAPS AND SKIPS, AND RETOOL.
<br />TOLERANCES.
<br />B. ACCURATELY FIT AND SECURE JOINTS AND INTERSECTIONS. MAKE JOINTS FLUSH, HAIRLINE, AND
<br />INTERFERE WITH SATISFACTORY INSTALLATION.
<br />/�
<br />DIVISION 10 SPECIALTIES
<br />I. PROTECT ALUMINUM MEMBERS IN CONTACT WITH MASONRY, STEEL, CONGFETE, OR DISSIMILAR MATERIALS
<br />USING NYLON PADS OR BITUMINOUS COATING.
<br />WEATHERTIGHT.
<br />B. INSPECT ALL GLASS IMMEDIATELY BEFOER INSTALLATION. REJECT ANY UNLABELED, EDGE -DAMAGED,
<br />SCRATCHED, OR MIS -SIZED PIECES. LEAVE MANUFACTURER'S LABELS ATTACHED UNTIL THE ARCHITEC
<br />1.03 CLEANING
<br />A UPON COMPLETION OF THE PLACEMENT AND GROUTING, CLEAN TILE SURFACE SO THAT THEY ARE FREE OF
<br />2. SHIM AND BRACE ALUMINALUMINUMM SYSTEM BEFORE ANCHORING TO STRUCTURE.
<br />C. FABRICATE IN LARGEST PRACTICAL UNITS.
<br />DIRECTS THAT THEY CAN BE REMOVED,
<br />FOREIGN MATTER REMOVE LATEX-PORTLAND CEMENT GROUT RESIDUE FROM TILE AS SOON AS POSSIBLE
<br />C. INSTALL AS PER MAUNFACTURER'S INSTRUCTIONS AND THE STANDARDS OF THE FLAT GLASS MARKETING
<br />UNGLAZED TILE MAY BE CLEANED WITH ACID SOLUTIONS ONLY WHEN PERMITTED BY TILE AND GROUT
<br />D. CONCEAL FASTENERS AND ATTACHMENTS FROM VIEW.
<br />ASSOCIATION.
<br />MANUFACTURER'S PRINTED INSTRUCTIONS, BUT SOONER THAN 14 DAYS AFTER INSTALLATION. FLUSH SURFACE
<br />305 FIELD QUALITY CONTROL
<br />A MANUFACTURER'S FIELD SERVICES: UPON OWNER'S REQUEST, PROVIDE MANUFACTURER'S FIELD SERVICE
<br />E. FABRICATE ALUMINUM COMPONENTS WITH INTEGRAL LOW CONDUCTANCE THERMAL BARRIER LOCATED
<br />D. MAINTAIN THE HIGHEST STANDARDS OF INSTALLATION AND CONSISTENCY IN APPLICATION AND APPEARANCE.
<br />WITH CLEAN WATER BEFORE AND AFTER CLEANING.
<br />NONE SPECIFIED
<br />CONSISTING OF PRODUCT USE RECOMMENDATIONS AND PERIODIC SITE VISIT FOR INSPECTION IN ACCORDANCE
<br />BETWEEN EXTERIOR AND INTERIOR EXPOSED COMPONENTS THAT ELIMINATES METAL -TO -METAL
<br />INSTALL SETTING BLOCKS AND SPACERS, GASKETS, AND FELTS EXACTLY AS DIRECTED BY MANUFACTURER
<br />END OF SECTION 09300
<br />WITH MANUFACTURER'S INSTRUCTIONS.
<br />CONTACT.
<br />SUPPORT GLASS FIRMLY AND EVENLY WITH SETTING BLOCKS. KEEP GLASS COMPLETELY SEPARATED FROM
<br />ANY MATERIAL OTHER THAN CUSHIONING STOPS, SPACERS, GASKETS, ETC. INSTALL GLASS TO MAINTAIN
<br />SECTION 09811 ACOUSTIC CEILINGS
<br />DIVISION 11 EQUIPMENT
<br />3.06 ADJUSTING AND GLEANING
<br />F DOORS:
<br />UNIFORM APPEARANCE IN SURFACES. DO NOT VARY GLAZING MATERIALS EXCEPT AS APPROVED OR
<br />PANEL
<br />A. ADJUSTING: ADJUST SWING DOORS FOR OPERATION IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS.
<br />I. MECHANICALLY FASTENED AND WELDED CORNER CONSTRUCTION.
<br />DIRECTED BY THE ARCHITECT.
<br />SEE SHEET Alb EQUIPMENT FLOOR PLAN
<br />CLEANING: THE GENERAL CONTRACTOR SHALL CLEAN INSTALLED PRODUCTS IN ACCORDANCE WITH
<br />2. FABRICATE STILES AND RAILS OF MINIMUM 0.188 INCH THICK EXTRUSIONS AND GLASS STOPS FROM
<br />E. INSTALL SEALANTS TO PROVIDE COMPLETE BOND AND TO ASSURE WATER WILL WASH AWAY FROM GLASS.
<br />PART 1 GENERAL -
<br />MANUFACTURER'S INSTRUCTIONS PRIOR TO OWNER'S ACCEPTANCE, AND REMOVE CONSTRUCTION DEBRIS FROM
<br />MINIMUM 0050 INCH THICK EXTRUSIONS.
<br />PROVIDE PRECISE MITER CUTS OR OTHER DIRECT JOINTS WHERE DETAILED. SEAL MITER JOINTS AND OTHER
<br />PROJECT SITE. LEGALLY DISP05E OF DEBRIS.
<br />3. PROVIDE WEATHERSTRIPPING AT DOOR HEAD, JAMBS, MEETING STILES, AND SILLS,
<br />JOINTS SO THEY ARE COMPLETELY AIRAND WATER TIGHT.
<br />IDI GENERAL
<br />PROTECTION: THE GENERAL CONTRACTOR SHALL PROTECT THE INSTALLED PRODUCT'S FINISH SURFACES FROM
<br />4. PREPARE WITH INTERNAL REINFORCEMENTS FOR DOOR HARDWARE.
<br />A COORDINATE LAYOUT AND INSTALLATION OF ACOUSTICAL CEILING UNITS AND 5U6PEN6ION SYSTEM
<br />DAMAGE DURING CONSTRUCTION.
<br />3D3 PROTECTION AFTER INSTALLATION
<br />COMPPONENTS WITH OTHER CONSTRUCTION THAT PENETRATES CEILINGS OR IS SUPPORTED BY THEM,
<br />t Q' ' Q
<br />DIVISION 12 1`URNIS�-IINCS
<br />END OF SECTION 08410
<br />2b FINISHES
<br />A PROTECT GLASS AFTER INSTALLATION WITH SAFTEY STRIPS AND WARNING MARKERS. KEEP SAFTEY STRIPS AND
<br />INCLUDING LIGHT FIXTURES AND HVAC EQUIPMENT.
<br />.
<br />WARNING MARKERS OFF THE GLASS SURFACE TO AVOID STAINING OR MARRING THE SURFACE. PROTECT METAL
<br />SEE ID SHEETS
<br />SECTION 08110 FINISH HARDWARE
<br />A ALUMINUM: AAMA 611, ARCHITECTURAL. CLASS I ANODIZED TO O.0001 INCH MINIMUM THICKNESS, CLEAR
<br />PARTS FROM DAMAGE AFTER INSTALLATION.
<br />1.02 MINERAL -FIBER ACOUSTICAL PANELS
<br />PART 1 GENERAL
<br />A PROVIDE ACOUSTICAL PANELS AS SPECIFIED ON SHEET IDI - FINISH SCHEDULE$, 24 INCHES B7 24 INCHES
<br />PART 3 EXECUTION
<br />3D4 CLEANING
<br />BY 3/4 INCHES THICK SQUARE EDGE. REFER TO DRAWINGS FOR COLOR SELECTION AND LIMITS OF TILE
<br />IDI GENERAL
<br />A OBTAIN EACH TYPE OF AS SPECIFIED IN THE DOOR/4ARDWARE SCHEDULE HARDWARE FROM A SINGLE
<br />3.1 INSTALLATION
<br />A CLEAN ALL GLASS AT THE CONCLUSION OF THE INTERIOR WORK, OR WHEN DIRECTED BY THE ARCHITECT.
<br />CLEAN ALL GLASS WITH GLEANER, CLEANING MATERIALS, AND METHODS I2ECOMMENED BY THE MANUFACTURER
<br />INSTALLATION.
<br />B. INSTALL IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS. ARRANGE ACOUSTICAL
<br />UNITS AND TILES FOR A UNIFORM APPEARANCE.
<br />.� tQ �y �
<br />`' Q �y � Qpr� CONSTRUCTION
<br />DIVISION 1�71V1� 13 SPECIAL VV1��7TIV1�1
<br />AL
<br />MANUFACTURER, ALTHOUGH SEVERAL MAY BE INDICATED AS OFFERING PRODUCTS COMPLYING WITH THE
<br />CLEAN ALL GLASS COMPLETLY CLEAR OF STREAKS OR SPOT
<br />ORIENT DIRECTIONAL PATTERN OF REST PANELS ON
<br />REQUIREMENTS.
<br />A INSTALL IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND APPROVED SHOP DRAWINGS.
<br />B. ANY GLASS THAT IS SCRATCHED OR DAMAGED DURING CLEANING WILL BE REPLACED AT THE CONTRACTOR'S
<br />FLANGES OR INVERTED TEES WITH TILE UNITS FITTING NEATLY AGAINST BUTTING SURFACE AND SUPPORT BY
<br />NONE SPECIFIED
<br />B. FURNISH ALL HARDWARE, IN THEIR ORIGINAL PACKAGING, COMPLETE WITH ACCE50RIES OF PROPER SIZE AND
<br />EXPENSE.
<br />WALL ANGLES
<br />DESIGN REQUIRED FOR THE PURPOSE FOR WHICH THEY An TO BE USED AND WITH ALL SCREWS, SHIELDS, AND
<br />B. INSTALL COMPONENTS PLUMB AND LEVEL, IN PROPER PLANE, FREE FROM WARP AND TWIST.
<br />OTHER ANCHORAGE DEVICES NECESSARY FOR A COMPLETE INSTALLATION. HARDWARE SCHEDULE SHOWN
<br />C. PROVIDE OWNER WITH MANUFACTURER'S INSTRUCTIONS FOR CLEANING.
<br />1.03 GYPSUM -BASE PANELS WITH VINYL MEMBRANE -FACED OVERLAY
<br />ON THE DRAWINGS.
<br />C. ANCHOR TO SUPPORTING CONSTRUCTION.
<br />3D5 REPAIR AND REPLACEMENT
<br />A PROVIDE PANELS AS SPECIFIED ON SHEET IDI - FINISH SCHEDULES, 24 INCHES BY 48 NCHES BY 1/2" THICK,
<br />C. INSTALL EACH HARDWARE ITEM IN COMPLIANCE WITH THE NATIONAL BUILDERS HARDWARE ASSOCIATION AND
<br />A REMOVE AND REPLACE ANY DAMAGE GLASS AND GLAZING. INSTALL, PROTECT, AND CLEAN REPLACEMENT
<br />03210 "STIPPLE WHITE." (TO BE INSTALLED AT FOOD PREP. AREAS)
<br />�1 /� `��/ SYSTEMS
<br />DIVISION 14 E IN� S S E
<br />THE MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. WHEREVER CUTTING AND FITTING IS REQUIRED TO
<br />D. SET THRESHOLDS AND SILL MEMBERS EXPOSED TO WEATHER IN MASTIC AND SECURE.
<br />B• INSTALL IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS. ARRANGE ACOUSTICAL
<br />VON 1� 1 I I 1S
<br />INSTALL HARDWARE ONTO OR INTO SURFACES WHICH ARE LATER TO BE PAINTED OR FINISHED IN ANOTHER
<br />GLASS AS SPECIFIED ABOVE.
<br />UNITS AND ORIENT DIRECTIONAL PATTERN OF TILES FOR A UNIFORM APPEARANCE. REST PANELS ON
<br />NONE SPECIFIED
<br />WAY, COORDINATED REMOVAL, STORAGE, AND REINSTALLATION OR APPLICATION OF SURFACE PROTECTIONS
<br />E. INSTALL HARDWARE USING TEMPLATES PROVIDED BY MANUFACTURER
<br />FLANGES OR INVERTED TEES WITH TILE UNITS FITTING NEATLY AGAINST BUTTING SURFACE SUPPORTED BY
<br />WITH FINISHING WORK
<br />END OF SECTION 98800
<br />WALL ANGLES.
<br />D. SET UNITS LEVEL, PLUMB AND TRUE TO LINE AND LOCATION. ADJUST AND REINFORCE THE ATTACHMENT
<br />F. INSTALL GLASS AND ACCESSORIES IN ACCORDANCE WITH SECTION 988000.
<br />SUBSTRATE AS NECESSARY FOR PROPER INSTALLATION AND OPERATION. DRILL AND COUNTERSINK UNITS NOT
<br />G. INSTALLATION TOLERANCES:
<br />ID4 METAL SUSPENSION SYSTEM
<br />FASTENERS. SPACE AND ANCHORS ACCORDANCE WITH
<br />ND IN RILL
<br />I. MAXIMUM VARIATION FROM PLUMB OR LEVEL: I/8 INCH IN 3 FEET OR I/4 INCH IN ANY 10 FEET,
<br />PROVIDE SYSTEM AS
<br />A DOUBLE WEB, INTEF41ED ATE DUTYY((ASTM C635)ELLECCTR ALVANIZED, COLD -ROLLED STEEL,15/I6 INCHES
<br />DIVISION 15 MECHANICAL
<br />SOTRRY STANDARDDS�SETATNHRESHOLDS FOR EXTERIOR DOORS BED OF BU YT LNWACCOR OF
<br />WHICHEVER IS LESS.
<br />POLYIOSBUTYLENE MASTIC SEALANT.
<br />2. MAXIMUM MISALIGNMENT MEMBERS ABUTTING END END: IINCH.
<br />WIDE, CAPPED BOTTOM FLANGE. WHITE IN COLOR SYSTEM TO INCLUDE ALL CROSS TEES, BRIDGING TREES,
<br />SEE MECHANICAL DRAWINGS
<br />E. ADJUST AND CHECK EACH OPERATING ITEM OF HARDWARE AND EACH DOOR TO ENSURE PROPER OPERATION.
<br />3. SEALANT SPACE BETWEENN ONSTRUCTION: I/2 INCH PLUS OR
<br />FRAMING MEMBERS AND ADJACENT CONSTRUCTION:
<br />D
<br />INTERSECTION CLIPS, SPLICES, COMPLETE EXPOSED GRID SYSTEM.
<br />REPLACE UNITS THAT CANNOT BE ADJUSTED TO OPERATE FREELY AND SMOOTHLY AS INTENDED FOR THE
<br />MINUS I/8 INCH.
<br />B. LAY OUT PATTERN IN ACCORDANCE WITH THE DRAWINGS, LEVEL, TRUE TO PLANE, AND AT THE REQUIRED
<br />MADE. INSTRUCT OWNERS IN PROPER ADJUSTMENT AND MAINTENANCE OF HARDWARE DURING
<br />ELEVATION. FRAME AROUND ALL OPENINGS IN CEILING LIGHTS AND GRILLES WITH MAIN RUNNERS. HANGERS
<br />FINAL ADJUSTMENT.
<br />32 ADJUSTING
<br />ARE TO BE SPACED At 4'-0" ON CENTER MAXIMUM, PROVIDE ADDITIONAL HANGERS AS REQUIRED TO
<br />ID2 KEYING
<br />SUPPORT LIGHT RES AND WVAC REGISTERSOINTERFERENCES CT WWORK
<br />/�'
<br />DIVISION * ELECTRICAL
<br />A KEYING SHALL BE PER THE OWNERS REQUIREMENTS. TAG KEYS AND PROVIDE TO OWNER AT SUBSTANTIAL
<br />A ADJUST HARDWARE FOR SMOOTH OPERATION
<br />C. SECURES WIRES BY LOOPING AND WIRE -TYING, EI� DIRECTLGRILLES Y
<br />OR TOINSERTS,
<br />COMPLETION
<br />SCREWS, OR OTHER DEVICES APPROPRIATE FOR SUBSTRATE. SCREW ATTACH EDGE MOLDINGS TO
<br />SEE ELECTRICAL DRAWINCxS
<br />I03 GUARANTEE
<br />B. ADJUST DOORS 70 OPERATE WITH MAXIMUM OPENING FORCES3/41N ACCORDANCE WITH APPLICABLE
<br />SUBSTRATE At INTERVALS NOT OVER 16 INCHES ON CENTER AND NOT MORE THAN 3 INCHES FROM ENDS.LEVEL
<br />A PROVIDE ONE-YEAR GUARANTEE FOR ALL HARDWARE. PERIOD OF GUARANTEE SHALL BEGIN FROM DATE OF
<br />ACCESSIBILITY CODE.
<br />GRID TO A TOLERANCE OF I/81NCH IN 12 FEET.
<br />•
<br />OWNER'S ACCEPTANCE.
<br />C. TOUCH UP MINOR SCRATCHES AND ABRASIONS TO MATCH ORIGINAL FINISH.
<br />.
<br />END OF SECTION OS511
<br />END OF SECTION 08-110
<br />D. ADJUST WEATHERSTRIPPING TO CONTACT APPROPRIATE SURFACES AND FORM WEATHER SEAL.
<br />END OF SPECIFICATIONS
<br />END OF SECTION
<br />REVISIONS
<br />BY
<br />-fi
<br />,
<br />.�
<br />,n
<br />J M :V
<br />�.
<br />J-1�
<br />_ �
<br />�~
<br />_ "
<br />ti
<br />-- -
<br />n I-u
<br />_ ti ri
<br />"V - 1
<br />`J
<br />��
<br />-
<br />o - u2
<br />u :I .
<br />" = L,
<br />�I
<br />. ti >
<br /><. , . _ .
<br />- 1 3
<br />ti
<br />�
<br />3
<br />3 r- 3
<br />._�
<br />- •
<br />-
<br />,_
<br />D
<br />r-�
<br />_�E ti o
<br />�ti
<br />�.�
<br />�---•
<br />Z ��
<br />. ,
<br />• -,
<br />- U
<br />�._
<br />w
<br />%
<br />11Ili
<br />0
<br />r� -1 I
<br />^
<br />e `" -
<br />, .
<br />y
<br />A I 1. ... �i
<br />: =,
<br />.
<br />. v
<br />• 1
<br />* �,
<br />.s
<br />s
<br />1 L � ..
<br />tee•.
<br />�_.,-
<br />a..
<br />0
<br />-7
<br />L
<br />O
<br />N
<br />C
<br />O
<br />a
<br />a
<br />-a
<br />C
<br />-0 •L
<br />O
<br />(1)_
<br />�
<br />in m iz
<br />o
<br />.L.
<br />m v vi
<br />O _
<br />w
<br />Q �
<br />s
<br />-v
<br />It -C
<br />N
<br />a
<br />N
<br />I`
<br />O
<br />.C:
<br />N
<br />c
<br />Date:
<br />06. 09. 15
<br />Scale:
<br />AS NOTED
<br />Project Mgr: RNS
<br />Drawn: DC
<br />Job:
<br />15-50
<br />Sheet
<br />N2
<br />
|