|
B. Finishing Gypsum Board Panels: Treat gypsum board joints, interior angles, edge trim, control joints, penetrations, fastener heads,
<br />surface defects, and elsewhere as required to prepare gypsum board surfaces for decoration.
<br />1. Prefill open joints and damaged surface areas.
<br />2. Apply joint tape over gypsum board joints, except those with trim having flanges not intended for tape.
<br />3. Glass -Mat Gypsum Sheathing Board: Finish according to manufacturer's written instructions for use as exposed soffit
<br />board.
<br />4. Glass -Mat, Water -Resistant Backing Panels: Finish according to manufacturer's written instructions.
<br />C. Gypsum Board Finish Levels: Finish panels to levels indicated below, according to ASTM C 840, for locations indicated:
<br />1. Level 4: Embed tape and apply separate first, fill, and finish coats of joint compound to tape, fasteners, and trim flanges at
<br />panel surfaces that will be exposed to view, unless otherwise indicated.
<br />END OF SECTION 09260
<br />SECTION 09512 - ACOUSTICAL TILE CEILINGS
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes acoustical tiles and concealed suspension systems for ceilings.
<br />1.2 SUBMITTALS
<br />A. Product Data: For each product indicated.
<br />B. Samples: For each acoustical tile, for each concealed suspension system member and for each color and texture required.
<br />C. Product test reports.
<br />1.3 QUALITY ASSURANCE
<br />A. Acoustical Testing Agency Qualifications: An independent testing laboratory or an NVLAP-accredited laboratory.
<br />B. Fire -Test -Response Characteristics:
<br />1. Fire -Resistance Ratings: Where indicated, provide acoustical tile ceilings identical to those of assemblies tested for fire
<br />resistance per ASTM E 119 by UL or another testing and inspecting agency acceptable to authorities having jurisdiction.
<br />Ratings are indicated by design designations from UL's "Fire Resistance Directory" or from the listings of another testing
<br />and inspecting agency.
<br />a. Identify materials with appropriate markings of applicable testing and inspecting agency.
<br />2. Surface -Burning Characteristics: Acoustical tiles complying with ASTM E 1264 for Class A materials, when tested per
<br />ASTM E 84.
<br />a. Smoke -Developed Index: 450 or less.
<br />C. Seismic Standard: Comply with the following:
<br />1. ASTM E 580.
<br />2. CISCA's "Recommendations for Direct -Hung Acoustical Tile and Lay -in Panel Ceilings --Seismic Zones 0-2."
<br />3. Mockups: Build mockups to verify selections made under sample Submittals and to
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />A. In other Part 2 articles where titles below introduce lists, the following requirements apply for product selection:
<br />1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but
<br />are not limited to, the products specified.
<br />2.2 GENERAL
<br />A. Acoustical Tile Standard: Comply with ASTM E 1264.
<br />B. Metal Suspension System Standard: Comply with ASTM C 635.
<br />C. Attachment Devices: Size for five times the design load indicated in ASTM C 635, Table 1, "Direct Hung," unless otherwise indi-
<br />cated.
<br />1. Anchors in Concrete: Expansion anchors fabricated from corrosion -resistant materials, with holes or loops for attaching
<br />hangers of type indicated and with capability to sustain, without failure, a load equal to five times that imposed by ceiling
<br />construction, as determined by testing per ASTM E 488 or ASTM E 1512 as applicable, conducted by a qualified testing and
<br />inspecting agency.
<br />2. Power -Actuated Fasteners in Concrete: Fastener system of type suitable for application indicated, fabricated from cor-
<br />rosion -resistant materials, with clips or other accessory devices for attaching hangers of type indicated, and with capabil-
<br />ity to sustain, without failure, a load equal to 10 times that imposed by ceiling construction, as determined by testing per
<br />ASTM E 1190, conducted by a qualified testing and inspecting agency.
<br />D. Wire Hangers, Braces, and Ties: Zinc -coated carbon -steel wire; ASTM A 641/A 641M, Class 1 zinc coating, soft temper.
<br />1. Size: Select wire diameter so its stress at three times hanger design load (ASTM C 635, Table 1, "Direct Hung") will be less
<br />than yield stress of wire, but provide not less than 0.106-inch- diameter wire.
<br />E. Seismic struts and seismic clips.
<br />F. Metal Edge Moldings and Trim: Type and profile indicated or, if not indicated, manufacturer's standard moldings for edges and
<br />penetrations that fit acoustical tile edge details and suspension systems indicated; formed from sheet metal of same material and
<br />finish as that used for exposed flanges of suspension system runners.
<br />2.3 ACOUSTICAL TILES
<br />A. General: Acoustical tiles shall be 24" x 48" x 5/8" matte finish mineral fiber ceiling boards and shall conform to Federal Specifica-
<br />tion SS-S-118a, Class 25. Light reflectance shall be no less than 75% and have NRC minimum range of .50 - .60.
<br />B. Products:
<br />1. Armstrong "Cortega".
<br />2. Celotex "Baroque"
<br />3. U.S.G. "Omni Fissured"
<br />2.4 METAL SUSPENSION SYSTEM
<br />A. General: The ceiling suspension system shall be an exposed grid system with exposed flanges having a factory applied white
<br />enamel finish with roll formed capped edges.
<br />1. Main Runner: DX-24
<br />2. Cross Tees: DX-424
<br />3. Wall Angle: M6S
<br />B. Products:
<br />2. Acoustical Tile Supplier Standard Grid System.
<br />C. Ceiling Suspension System: Direct hung; ASTM C 635, intermediate -duty structural classification.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. General: Install acoustical tile ceilings to comply with ASTM C 636 and seismic requirements indicated, per manufacturer's writ-
<br />ten instructions and CISCA's "Ceiling Systems Handbook."
<br />B. Measure each ceiling area and establish layout of acoustical tiles to balance border widths at opposite edges of each ceiling. Avoid
<br />using less -than -half -width tiles at borders.
<br />C. Suspend ceiling hangers from building's structural members, plumb and free from contact with insulation or other objects within
<br />ceiling plenum. Splay hangers only where required to miss obstructions; offset resulting horizontal forces by bracing, counter -
<br />splaying, or other equally effective means. Where width of ducts and other construction within ceiling plenum produces hanger
<br />spacings that interfere with location of hangers, use trapezes or equivalent devices.
<br />1. Do not support ceilings directly from permanent metal forms or floor deck; anchor into concrete slabs.
<br />2. Do not attach hangers to steel deck tabs or to steel roof deck.
<br />D. Install edge moldings and trim at perimeter of acoustical tile ceiling area and where necessary to conceal edges of acoustical units.
<br />Screw attach moldings to substrate with concealed fasteners at intervals not more than 16 inches o.c. and not more than 3 inches
<br />from ends, leveling with ceiling suspension system to a tolerance of 1/8 inch in 12 feet. Miter corners accurately and connect
<br />securely.
<br />E. Install suspension system runners so they are square and securely interlocked with one another. Remove and replace dented, bent,
<br />or kinked members.
<br />F. Install acoustical tiles in coordination with suspension system and exposed moldings and trim. Place splines or suspension system
<br />flanges into kerfed edges so tile -to -tile joints are closed by double lap of material. Fit adjoining tile to form flush, tight joints.
<br />Scribe and cut tile for accurate fit at borders and around penetrations through tile. Hold tile field in compression by inserting leaf -
<br />type, spring -steel spacers between tile and moldings, spaced 12 inches o.c.
<br />END OF SECTION 09512
<br />SECTION 09653 - RESILIENT WALL BASE AND ACCESSORIES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes the following:
<br />1. Wall base.
<br />1.2 SUBMITTALS
<br />A. Product Data: None.
<br />B. Samples: For each type of product indicated, in manufacturer's standard -size Samples but not less than 12 inches (300 mm) long,
<br />of each resilient product color, texture, and pattern required. Submit directly to the owner for approval.
<br />1.3 PROJECT CONDITIONS
<br />A. Maintain temperatures within range recommended by manufacturer, but not less than 70 deg F (21 deg C) or more than 95 deg F
<br />(35 deg C), in spaces to receive floor tile during the following time periods:
<br />1. 48 hours before installation.
<br />2. During installation.
<br />3. 48 hours after installation.
<br />B. After postinstallation period, maintain temperatures within range recommended by manufacturer, but not less than 55 deg F (13
<br />deg C) or more than 95 deg F (35 deg Q.
<br />C. Install resilient products after other finishing operations, including painting, have been completed.
<br />1.4 EXTRA MATERIALS
<br />A. Furnish extra materials described below that match products installed and that are packaged with protective covering for storage
<br />and identified with labels describing contents.
<br />1. Furnish not less than 10 linear feet (3 linear m) for every 500 linear feet (150 linear m) or fraction thereof, of each type,
<br />color, pattern, and size of resilient product installed.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />A. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are
<br />not limited to, products listed in other Part 2 articles.
<br />B. Products: Subject to compliance with requirements, provide one of the products listed in other Part 2 articles.
<br />2.2 COLORS AND PATTERNS
<br />A. Colors and Patterns: As selected from manufacturer's full range.
<br />2.3 RESILIENT WALL BASE
<br />A. Wall Base: ASTM F 1861.
<br />1. AFCO-USA, American Floor Products Company, Inc.
<br />2. Armstrong World Industries, Inc.
<br />3. Johnsonite.
<br />4. Roppe Corporation.
<br />B. Type (Material Requirement): TV (vinyl), TS (rubber, vulcanized thermoset) or TP (rubber, thermoplastic).
<br />C. Group (Manufacturing Method): I (solid).
<br />D. Style: Cove (with top -set toe).
<br />E. Minimum Thickness: 0.125 inch (3.2 mm).
<br />F. Height: 6 inches (102 mm).
<br />G. Lengths: Cut lengths 48 inches (1219 mm) long or coils in manufacturer's standard length.
<br />H. Outside Corners: Job formed or premolded.
<br />I. Inside Corners: Job formed or premolded.
<br />J. Surface: Smooth.
<br />2.4 INSTALLATION MATERIALS
<br />A. Trowelable Leveling and Patching Compounds: Latex -modified, portland cement based or blended hydraulic cement based for-
<br />mulation provided or approved by resilient product manufacturers for applications indicated.
<br />B. Adhesives: Water-resistant type recommended by manufacturer to suit resilient products and substrate conditions indicated.
<br />PART 3 - EXECUTION
<br />3.1 PREPARATION
<br />A. Prepare substrates according to manufacturer's written recommendations to ensure adhesion of resilient products.
<br />B. Concrete Substrates for Stair Accessories: Prepare according to ASTM F 710.
<br />1. Verify that substrates are dry and free of curing compounds, sealers, and hardeners.
<br />2. Alkalinity and Adhesion. Testing: Perform tests recommended by manufacturer. Proceed with installation only after sub-
<br />strates pass testing.
<br />3. Moisture Testing:
<br />a. Perform anhydrous calcium chloride test, ASTM F 1869. Proceed with installation only after substrates have maxi-
<br />mum moisture -vapor -emission rate of 3 lb of water/1000 sq. ft. (1.36 kg of water/92.9 sq. m) in 24 hours.
<br />b. Perform tests recommended by manufacturer. Proceed with installation only after substrates pass testing.
<br />C. Remove substrate coatings and other substances that are incompatible with adhesives and that contain soap, wax, oil, or silicone,
<br />using mechanical methods recommended by manufacturer. Do not use solvents.
<br />D. Use trowelable leveling and patching compound to fill cracks, holes, and depressions in substrates.
<br />E. Move resilient products and installation materials into spaces where they will be installed at least 48 hours in advance of installa-
<br />tion.
<br />1. Do not install resilient products until they are the same temperature as the space where they are to be installed.
<br />F. Sweep and vacuum clean substrates to be covered by resilient products immediately before installation. After cleaning, examine
<br />substrates for moisture, alkaline salts, carbonation, and dust. Proceed with installation only after unsatisfactory conditions have
<br />been corrected.
<br />3.2 RESILIENT WALL BASE INSTALLATION
<br />A. Apply wall base to walls, columns, pilasters, casework and cabinets in toe spaces, and other permanent fixtures in rooms and areas
<br />where base is required.
<br />B. Install wall base in lengths as long as practicable without gaps at seams and with tops of adjacent pieces aligned.
<br />C. Tightly adhere wall base to substrate throughout length of each piece, with base in continuous contact with horizontal and vertical
<br />substrates.
<br />D. Do not stretch wall base during installation.
<br />E. On masonry surfaces or other similar irregular substrates, fill voids along top edge of wall base with manufacturer's recommended
<br />adhesive filler material.
<br />F. Premolded Corners: Install premolded corners before installing straight pieces.
<br />G. Job -Formed Corners:
<br />1. Outside Corners: Use straight pieces of maximum lengths possible. Form without producing discoloration (whitening) at
<br />bends. Shave back of base at points where bends occur and remove strips perpendicular to length of base that are only deep
<br />enough to produce a snug fit without removing more than half the wall base thickness.
<br />2. Inside Corners: Use straight pieces of maximum lengths possible. Form by cutting an inverted V-shaped notch in toe of
<br />wall base at the point where corner is formed. Shave back of base where necessary to produce a snug fit to substrate.
<br />3.3 CLEANING AND PROTECTION
<br />A. Perform the following operations immediately after completing resilient product installation:
<br />1. Remove adhesive and other blemishes from exposed surfaces.
<br />2. Sweep and vacuum surfaces thoroughly.
<br />3. Damp -mop surfaces to remove marks and soil.
<br />a. Do not wash surfaces until after time period recommended by manufacturer.
<br />B. Protect resilient products from mars, marks, indentations, and other damage from construction operations and placement of equip -
<br />gild, res dijrina r , i der of cqn . , .ti: rigid. Uw protection met ods reeomm__ended in -,-Htinu by manufacturer.
<br />xn. nt and .... _ .. _ kx�. _ ema_n . e..�. _ stn c ..on e_. _ : _ . on 11
<br />END OF SECTION 09653
<br />SECTION 09900 - PAINT AND WALL FINISHES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes surface preparation and field painting of exposed items and surfaces.
<br />1.2 SUBMITTALS
<br />A. Product Data: For each product indicated.
<br />B. Samples: For each type of finish -coat material indicated. To be submitted directly to the owner for approval.
<br />1.3 QUALITY ASSURANCE
<br />A. Benchmark Samples (Mockups): Provide a full -coat benchmark finish sample for each type of coating and substrate required.
<br />Comply with procedures specified in PDCA P5.
<br />1. Wall Surfaces: Provide samples on at least 100 sq. ft..
<br />2. Small Areas and Items: Architect will designate items or areas required.
<br />3. Final approval of colors will be from benchmark samples.
<br />1.4 PROJECT CONDITIONS
<br />A. Store materials not in use in tightly covered containers in a well -ventilated area at a minimum ambient temperature of 45 deg F.
<br />Maintain storage containers in a clean condition, free of foreign materials and residue.
<br />B. Apply waterborne paints only when temperatures of surfaces to be painted and surrounding air are between 50 and 90 deg F.
<br />C. Apply solvent -thinned paints only when temperatures of surfaces to be painted and surrounding air are between 45 and 95 deg F
<br />D. Do not apply paint in snow, rain, fog, or mist; or when relative humidity exceeds 85 percent; or at temperatures less than 5 deg F
<br />above the dew point; or to damp or wet surfaces.
<br />1.5 EXTRA MATERIALS
<br />A. Furnish extra paint materials from the same production run as the materials applied and in the quantities described below. Package
<br />with protective covering for storage and identify with labels describing contents. Deliver extra materials to Owner.
<br />1. Quantity: 3 percent, but not less than 1 gal. or 1 case, as appropriate, of each material and color applied.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />A. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are
<br />not limited to, products listed in other Part 2 articles.
<br />t tcomplianceith re requirements, provide one of the products listed in other Part 2 articles.
<br />B. Products: Subject o w q , p
<br />C. Manufacturers' Names: Shortened versions (shown in parentheses) of the following manufacturers' names are used in other Part 2
<br />articles:
<br />1. Benjamin Moore & Co. (Benjamin Moore).
<br />2. ICI Dulux Paint Centers (ICI Dulux Paints).
<br />3. Sherwin-Williams Co. (Sherwin-Williams).
<br />2.2 PAINT MATERIALS, GENERAL
<br />A. Material Compatibility: Provide block fillers, primers, and finish -coat materials that are compatible with one another and with
<br />the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field
<br />experience.
<br />B. Material Quality: Provide manufacturer's best -quality paint material of the various coating types specified that are factory for-
<br />mulated and recommended by manufacturer for application indicated. Paint -material containers not displaying manufacturer's
<br />product identification will not be acceptable.
<br />C. Colors: As indicated by manufacturer's designations.
<br />2.3 PREPARATORY COATS
<br />A. Interior Primer: Interior latex -based or alkyd primer of finish coat manufacturer and recommended in writing by manufacturer for
<br />use with finish coat and on substrate indicated.
<br />1. Ferrous -Metal Substrates: Quick drying, rust -inhibitive metal primer.
<br />2. Zinc -Coated Metal Substrates: Galvanized metal primer.
<br />3. Where manufacturer does not recommend a separate primer formulation on substrate indicated, use paint specified for finish
<br />coat.
<br />2.4 INTERIOR FINISH COATS
<br />A. Interior Low -Luster Acrylic Enamel:
<br />1. Benjamin Moore; Moorcraft Super Spec Latex Eggshell Enamel No. 274.
<br />2. ICI Dulux Paints; 1402 series Dulux Professional Acrylic Eggshell Interior Wall & Trim Enamel.
<br />3. Sherwin-Williams; ProMar 200 Interior Latex Egg -Shell Enamel B20W200 Series.
<br />PART 3 - EXECUTION
<br />3.1 APPLICATION
<br />A. Comply with procedures specified in PDCA P4 for inspection and acceptance of surfaces to be painted.
<br />B. Coordination of Work: Review other Sections in which primers are provided to ensure compatibility of the total system for various
<br />substrates. On request, furnish information on characteristics of finish materials to ensure use of compatible primers.
<br />C. Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and similar items already installed that
<br />are not to be painted. If removal is impractical or impossible because of size or weight of the item, provide surface -applied protec-
<br />tion before surface preparation and painting.
<br />1. After completing painting operations in each space or area, reinstall items removed using workers skilled in the trades
<br />involved.
<br />D. Surface Preparation: Clean and prepare surfaces to be painted according to manufacturer's written instructions for each particular
<br />substrate condition and as specified.
<br />1. Provide barrier coats over incompatible primers or remove and reprime.
<br />2. Cementitious Materials: Remove efflorescence, chalk, dust, dirt, grease, oils, and release agents. Roughen as required to
<br />remove glaze. If hardeners or sealers have been used to improve curing, use mechanical methods of surface preparation.
<br />3. Wood: Clean surfaces of dirt, oil, and other foreign substances with scrapers, mineral spirits, and sandpaper, as required.
<br />Sand surfaces exposed to view smooth and dust off.
<br />a. Scrape and clean small, dry, seasoned knots, and apply a thin coat of white shellac or other recommended knot sealer
<br />before applying primer. After priming, fill holes and imperfections in finish surfaces with putty or plastic wood filler.
<br />Sand smooth when dried.
<br />b. Prime, stain, or seal wood to be painted immediately on delivery. Prime edges, ends, faces, undersides, and back
<br />sides of wood, including cabinets, counters, cases, and paneling.
<br />C. If transparent finish is required, backprime with spar varnish.
<br />d. Backprime paneling on interior partitions where masonry, plaster, or other wet wall construction occurs on back
<br />side.
<br />e. Seal tops, bottoms, and cutouts of unprimed wood doors with a heavy coat of varnish or sealer immediately on deliv-
<br />ery.
<br />4. Ferrous Metals: Clean ungalvanized ferrous -metal surfaces that have not been shop coated; remove oil, grease, dirt, loose
<br />mill scale, and other foreign substances. Use solvent or mechanical cleaning methods that comply with SSPC's recommen-
<br />dations.
<br />a. Blast steel surfaces clean as recommended by paint system manufacturer and according to SSPC-SP 6/NACE No. 3.
<br />b. Treat bare and sandblasted or pickled clean metal with a metal treatment wash coat before priming.
<br />C. Touch up bare areas and shop -applied prime coats that have been damaged. Wire -brush, clean with solvents recom-
<br />mended by paint manufacturer, and touch up with same primer as the shop coat.
<br />5. Galvanized Surfaces: Clean galvanized surfaces with nonpetroleum-based solvents so surface is free of oil and surface
<br />contaminants. Remove pretreatment from galvanized sheet metal fabricated from coil stock by mechanical methods.
<br />E. Material Preparation:
<br />1. Maintain containers used in mixing and applying paint in a clean condition, free of foreign materials and residue.
<br />2. Stir material before application to produce a mixture of uniform density. Stir as required during application. Do not stir
<br />surface film into material. If necessary, remove surface film and strain material before using.
<br />F. Exposed Surfaces: Include areas visible when permanent or built-in fixtures, grilles, convector covers, covers for finned -tube
<br />radiation, and similar components are in place. Extend coatings in these areas, as required, to maintain system integrity and pro-
<br />vide desired protection.
<br />1. Paint surfaces behind movable equipment and furniture the same as similar exposed surfaces. Before final installation of
<br />equipment, paint surfaces behind permanently fixed equipment or furniture with prime coat only.
<br />2. Paint interior surfaces of ducts with a flat, nonspecular black paint where visible through registers or grilles.
<br />3. Paint back sides of access panels and removable or hinged covers to match exposed surfaces.
<br />4. Finish exterior doors on tops, bottoms, and side edges the same as exterior faces.
<br />5. Finish interior of wall and base cabinets and similar field -finished casework to match exterior.
<br />G. Sand lightly between each succeeding enamel or varnish coat.
<br />H. Scheduling Painting: Apply first coat to surfaces that have been cleaned, pretreated, or otherwise prepared for painting as soon as
<br />practicable after preparation and before subsequent surface deterioration.
<br />1. Omit primer over metal surfaces that have been shop primed and touchup painted.
<br />2. If undercoats, stains, or other conditions show through final coat of paint, apply additional coats until paint film is of uniform
<br />finish, color, and appearance.
<br />I. Application Procedures: Apply paints and coatings by brush, roller, spray, or other applicators according to manufacturer's written
<br />instructions.
<br />J. Minimum Coating Thickness: Apply paint materials no thinner than manufacturer's recommended spreading rate. Provide total
<br />dry film thickness of the entire system as recommended by manufacturer.
<br />K. Mechanical and Electrical Work: Painting of mechanical and electrical work is limited to items exposed in equipment rooms and
<br />occupied spaces.
<br />L. Block Fillers: Apply block fillers to concrete masonry block at a rate to ensure complete coverage with pores filled.
<br />M. Prime Coats: Before applying finish coats, apply a prime coat, as recommended by manufacturer, to material that is required_ to
<br />oe painted or finished and that has not teen prime coated by others. Recoat primed and sealed surfaces where evidence of suction
<br />spots or unsealed areas in first coat appears, to ensure a finish coat with no burn -through or other defects due to insufficient seal-
<br />ing.
<br />N. Pigmented (Opaque) Finishes: Completely cover surfaces as necessary to provide a smooth, opaque surface of uniform finish,
<br />color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfec-
<br />tions will not be acceptable.
<br />O. Transparent (Clear) Finishes: Use multiple coats to produce a glass -smooth surface film of even luster. Provide a finish free of
<br />laps, runs, cloudiness, color irregularity, brush marks, orange peel, nail holes, or other surface imperfections.
<br />P. Stipple Enamel Finish: Roll and redistribute paint to an even and fine texture. Leave no evidence of rolling, such as laps, irregu-
<br />larity in texture, skid marks, or other surface imperfections.
<br />3.2 CLEANING AND PROTECTING
<br />A. At the end of each workday, remove empty cans, rags, rubbish, and other discarded paint materials from Project site.
<br />B. Protect work of other trades, whether being painted or not, against damage from painting. Correct damage by cleaning, repairing
<br />or replacing, and repainting, as approved by Architect.
<br />C. Provide "Wet Paint" signs to protect newly painted finishes. After completing painting operations, remove temporary protective
<br />wrappings provided by others to protect their work.
<br />1. After work of other trades is complete, touch up and restore damaged or defaced painted surfaces. Comply with procedures
<br />specified in PDCA PL
<br />3.3 INTERIOR PAINT SCHEDULE
<br />A. Gypsum Board:
<br />1. Acrylic Finish: Two finish coats over a primer.
<br />a. Primer: Interior gypsum board primer.
<br />b. Finish Coats: See section 2.5.
<br />B. Wood and Hardboard:
<br />l . Acrylic -Enamel Finish: Two finish coats over a primer.
<br />a. Primer: Interior wood primer for acrylic -enamel and semigloss alkyd -enamel finishes.
<br />b. Finish Coats: See section 2.5.
<br />END OF SECTION 09900
<br />SECTION 10801- TOILET AND BATH ACCESSORIES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes the following:
<br />1. Toilet and bath accessories.
<br />2. Underlavatory guards.
<br />1.2 QUALITY ASSURANCE
<br />A. Inserts and Anchorage: Furnish inserts and anchoring devices and coordinate delivery with other work to avoid delay
<br />B. Provide products of the same manufacturer for each type of accessory unit and for units exposed in the same areas.
<br />C. Special Mirror Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace mirrors that develop
<br />visible silver spoilage defects within 15 years from date of Substantial Completion.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
<br />1. Toilet and Bath Accessories:
<br />a. American Specialties, Inc.
<br />b. Bobrick Washroom Equipment, Inc.
<br />C. Bradley Corporation.
<br />2. Underlavatory Guards:
<br />a. Truebro, Inc.
<br />b. Plumberex Specialty Products, Inc.
<br />2.2 SCHEDULE OF TOILET ACCESSORIES
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Install accessories using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level,
<br />plumb, and firmly anchored in locations and at heights indicated. Provide blocking where required to meet force requirements
<br />indicted below. Ensure blocking is Fire retardent in walls that are rated or are otherwise required to be non-combustible
<br />1. Install grab bars to withstand a downward load of at least 2501bf, when tested according to method in ASTM F 446.
<br />B. Adjust accessories for unencumbered, smooth operation and verify that mechanisms function properly. Replace damaged or
<br />defective items. Remove temporary labels and protective coatings.
<br />END OF SECTION 10801
<br />•,
<br />z
<br />jLU o
<br />J CO
<br />m it
<br />b
<br />¢ Q
<br />w �
<br />>
<br />J
<br />HLL
<br />W
<br />LU
<br />w
<br />cc
<br />U.,
<br />Cl-
<br />CD
<br />CM
<br />0
<br />r
<br />W
<br />o
<br />N
<br />Q
<br />L1JJ
<br />w
<br />N
<br />M
<br />'V
<br />CD
<br />1`
<br />:.
<br />0
<br />ui T
<br />m
<br />m
<br />W
<br />coW
<br />o
<br />z
<br />w
<br />Y
<br />It
<br />N
<br />N
<br />C,7
<br />= m
<br />0-
<br />O
<br />U
<br />TENANT BUILD OUT
<br />A004
<br />
|