Laserfiche WebLink
—! II 1 1 — I _ ' [.11 1 <br />12 <br />4.01 <br />RAISED BANDS OR FOAM <br />PER COMMUNITY <br />SPECIFICATIONS —� <br />12 <br />15.0 FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />-I------------------ - ---� <br />N - HDR. <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />N CV FLASHING111 <br />25-SH----------2�Sti--- — --- <br />2ND FIN <br />Aw. <br />---- — — ------------------------------- <br />� FM�-- <br />S� TEXTURED <br />SCORED 1 I � El � � F/7< Ll 1 ! CEMENTITIOUS <br />STUCCO TYP.—, FINISH ON <br />N CMU(TYP) <br />is <br />v <br />CV <br />- - -LAI_ _ FIN FLR <br />3068 �T <br />FRONT ELEVATION — B. <br />SCALE: 1/4" = V-0" <br />9'-0" RIDGE VENT <br />Co <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />=------------------------- <br />- <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />12 <br />14.0 --- 2ND <br />FIN I <br />T.0 <br />x--TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) LEFT ELEVATION — B <br />SCALE: 1/4" = 1'-0" <br />1� DETAIL <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />e+•s <br />cwa <br />® <br />� <br />L <br />p <br />5 <br />p W <br />a. t <br />Q <br />M <br />E M�� <br />U_ <br />-�Ccx <br />N�o <br />N 01 C7 rp <br />•a[ N Y <br />3 = a' <br />3 M <br />3 �- <br />� J d <br />� C O <br />= E <br />e0 p <br />ci J <br />a <br />cWWN <br />\valcC <br />•� <br />f \ <br />F <br />• •' <br />••......••' <br />�� <br />��, <br />E55'0 <br />�rtljl}1tiltt� � <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal. <br />of <br />_.. W <br />a <br />E <br />co ci <br />C <br />co <br />ui <br />UI�0 J <br />Q <br />N O� <br />C J 2 <br />W <br />J LL LL SSS p, <br />Z <br />0 <br />C- a 4 <br />W <br />'gC� <br />Z <br />2 <br />IL <br />M du <br />Zo < <br />U) M z d <br />Z <br />of 0 <br />N 6 U v <br />W <br />❑ ❑ <br />Z � <br />M <br />z � <br />Z o <br />C) <br />J <br />r <br />U <br />U1 <br />z g <br />c� <br />dj <br />4.1 <br />C6 <br />w <br />o <br />0 <br />w s <br />N <br />c N <br />�N <br />,— r' <br />n3 <br />(a <br />U iu <br />LL1J <br />( <br />J <br />_ E <br />t <br />I <br />U 'o <br />Q Y <br />° <br />(V O! <br />o <br />w <br />M <br />0 <br />Z <br />Q E <br />o <br />Z O <br />wo <br />g <br />> N <br /><ry <br />=_® <br />`a <br />o0 <br />~ E <br />CD <br />x U <br />¢a <br />Q 2 <br />=O U <br />O� <br />W Z <br />N M <br />t <br />o <br />o <br />�w <br />.� <br />./ <br />v <br /><Y <br />�x <br />m 0 <br />& <br /><� <br />Zox <br />3 <br />a� <br />0 � <br />aU <br />�w <br />W <br />aLL <br />� <br />w <br />MI5 <br />>O <br />CDw� <br />CC) <br />a <br />°3 <br />V <br />is <br />0 <br />> Ul) <br />0 <br />m <br />rn <br />m <br />co <br />0 <br />O <br />Q <br />Cr0 <br />co <br />0 <br />�- <br />W m <br />� <br />c <br />Cfl <br />C7 N <br />Q� <br />to o <br />Ltd <br />r <br />M LO <br />T <br />E <br />c <br />(h CN <br />Z <br />N <br />Z <br />E O <br />Mf f <br />a. <br />Eio <br />U <br />Q p <br />JOB <br />NO: <br />22-12355 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.1 <br />