|
Li
<br />CONSTRUCTION NOTES:
<br />1. THE PROJECT IS AN INTERIOR REMODEL. ONLY MINOR EXTERIOR (SHELL) WORK
<br />IS PROPOSED. NO SITE WORK IS PROPOSED.
<br />2. ALL WORK SHALL BE COMPLETED IN STRICT ACCORDANCE WITH ALL
<br />MANUFACTURER'S SPECIFICATIONS, GUIDELINES, AND RECOMMENDATIONS; AS
<br />WELL AS ALL PERTINENT FEDERAL, STATE, AND LOCAL CODES AND ORDINACES
<br />INCLUDING BUT NOT LIMITED TO:
<br />* FLORIDA BUILDING CODE, (2007) W/ 2009 SUPPLEMENTS
<br />3. PRIOR TO START OF WORK, GENERAL CONTRACTOR, (G.C.), SHALL REVIEW THESE
<br />CONSTRUCTION DOCUMENTS AND THE PRINTED SCOPE OF WORK TO BE
<br />PERFORMED UNDER THE CONSTRUCTION CONTRACT WITH A DULY AUTHORIZED
<br />REPRESENTATIVE OF THE TENANT, THE ARCHITECT DOES NOT REPRESENT THESE
<br />DOCUMENTS AS APPROVED BY THE TENANT. SCOPE OF WORK IS AVAILABLE
<br />FROM TENANT'S REPRESENTATIVE.
<br />4. THE CONTRACTOR FOR THIS PROJECT SHALL INCLUDE ALL MATERIALS AND
<br />LABOR REQUIRED TO COMPLETE THE TOTAL PROJECT. THE CONTRACTOR SHALL
<br />FURNISH AND PAY FOR ALL MATERIALS, TOOLS, EQUIPMENT, LABOR, MACHINERY,
<br />TRANSPORTATION, HEAT, WATER, UTILITIES, AND ALL OTHER FACILITIES AND
<br />SERVICES REQUIRED FOR THE SAFE AND PROPER EXECUTION AND COMPLETION
<br />OF THE WORK.
<br />5. ALL FINAL COLOR AND FINISH SELECTIONS SHALL BE APPROVED, IN WRITING, BY
<br />THE TENANT. IN GENERAL, NEW CONSTRUCTION SHALL MATCH EXISTING AND
<br />CONTIGUOUS CONSTRUCTION IN COLOR, FINISH, MANUFACTURER, AND INSTALLATION
<br />METHOD.
<br />6. G.C. SHALL FIELD VERIFY KEY DIMENSIONS AND CONDITIONS PRIOR TO
<br />ORDERING MATERIALS, FINISHES, EQUIPMENT, AND FIXTURES. THESE
<br />CONSTRUCTION DOCUMENTS ARE BASED, IN LARGE PART, ON TENANT -SUPPLIED
<br />RECORD CONSTRUCTION DOCUMENTS ("AS BUILTS"). THE ARCHITECT DOES NOT
<br />REPRESENT THAT HE HAS FIELD -VERIFIED THE RECORD CONSTRUCTION
<br />DOCUMENTS AND HE DOES NOT CERTIFY THEIR ACCURACY.
<br />7. NOT ALL AREAS OF THE PROJECT LOCATION WERE AVAILABLE FOR
<br />OBSERVATION AND VERIFICATION AT THE TIME THESE CONSTRUCTION DOCUMENTS
<br />WERE PREPARED. CONSEQUENTLY, THE ARCHITECT DOES NOT CERTIFY THEIR
<br />ACCURACY. THESE CONSTRUCTION DOCUMENTS SHALL NOT BE REFERENCED AS
<br />A LEASE EXHIBIT.
<br />8. GENERAL CONTRACTOR REMAINS SOLELY LIABLE AND RESPONSIBLE FOR THE
<br />FOLLOWING:
<br />- VERIFICATION OF ALL EXISTING CONDITIONS, UNIT LOCATIONS AND DIMENSIONS
<br />COORDINATING W/ TRADES AND TENANT PRIOR TO CONSTRUCTION
<br />- IDENTIFICATION AND REMOVAL OF ANY AND ALL HAZARDOUS MATERIALS,
<br />INCLUDING, BUT NOT LIMITED TO, ABESTOS-LADEN MATERIALS. (NOTIFY
<br />TENANT BEFORE REMOVAL, IN WRITING, IF ANY HAZARDOUS MATERIALS ARE
<br />DISCOVERED.)
<br />- THE VERIFICATION AND MAINTENANCE OF ALL EXISTING SETBACKS, EASEMENTS,
<br />AND ANY DEED RESTRICTIONS.
<br />- COORDINATION OF WORKING HOURS, DELIVERIES, TRASH REMOVAL, STORAGE,
<br />ETC. WITH LANDLORD.
<br />- ERECTION PROCEDURE AND SEQUENCE TO ENSURE THE INTEGRITY OF THE
<br />BUILDING AND IT'S COMPONENT PARTS DURING CONSTRUCTION.
<br />- COORDINATION OF ARCHITECTURAL, STRUCTURAL, MECHANICAL AND
<br />ELECTRICAL DETAILS AND DIMENSIONS. ANY DISCREPANCIES BETWEEN SUCH
<br />DETAILS AND DIMENSIONS SHALL BE REPORTED TO THE ARCHITECT PRIOR TO
<br />PROCEEDING W/ THE WORK.
<br />- ACCESS PANELS WHERE REQUIRED AS PER PLANS, SPECIFICATIONS, OR
<br />INSTRUCTIONS.
<br />9. THE CONTRACTOR SHALL PROVIDE THE OWNER W/ A SWORN LIST OF
<br />SUBCONTRACTORS AND MATERIAL PROVIDED PRIOR TO CONSTRUCTION. THE
<br />SAID LIST SHALL BE UPDATED EACH MONTH THEREAFTER.
<br />10. FOR ALL INTENTS AND PURPOSES, THE CERTIFICATE OF OCCUPANCY SHALL
<br />SERVE AS "SUBSTANTIAL COMPLETION".
<br />11. IF THE DRAWINGS AND THE FIELD CONDITIONS ARE NOT IN AGREEMENT, THE
<br />CONTRACTOR TO NOTIFY THE G.C. AND/OR ARCHITECT/ENGINEER BEFORE STARTING
<br />ANY WORK. ANY INCONSISTENCIES NEED TO BE CORRECTED BEFORE INSTALLATION
<br />BEGINS. IF THE CONTRACTOR STARTS INSTALLATION WITHOUT THE CORRECTED
<br />DRAWINGS, HE/SHE WILL BE RESPONSIBLE FOR ANY AND ALL COSTS (BEYOND THE
<br />ORIGINAL CONTRACTED AMOUNT) INCURRED BY NECESSARY CHANGES TO CORRECT
<br />THE INCONSISTENCIES.
<br />12. CLEAN INTERIOR AND EXTERIOR OF ALL WINDOW GLASS PRIOR TO TURNING SPACE
<br />OVER TO F.D.S. REMOVE ALL TAPE & OTHER ITEMS ATTACHED TO GLASS OR FRAMES.
<br />13. G.C. WILL TEST ALL HVAC UNITS FOR HEAT AND COOLING PRIOR TO FDS POSSESSION
<br />OF SPACE.
<br />DEMOLITION NOTES.-
<br />14. ALL EXISTING STRUCTURAL MEMBERS AND ANY EXTERIOR OPENINGS (ALL
<br />EXISTING JOB -SITE CONDITIONS) SHALL BE VERIFIED BY THE CONTRACTOR
<br />PRIOR TO ANY MODIFICATION.
<br />15. ALL NEW INTERIOR CONCRETE SLABS AND FOUNDATION WALLS AND FOOTINGS
<br />SHALL HAVE SOIL POISONING UNDER NEW WORK AND SHALL BE INSTALLED BY A
<br />LICENSED CONTRACTOR. ALL WORK SHALL BE COMPLETED IN ACCORDANCE
<br />WITH ALL STATE AND DEPARTMENT OF AGRICULTURE, STRUCTURAL PEST CONTROL
<br />DIVISION REGULATIONS RULES DEFINITIONS AND REQUIREMENTS.
<br />16. ALL DIMENSIONAL LUMBER, PLYWOOD, PARTICLE BOARDS, ETC. USED IN
<br />CONTRUCTION SHALL BE FIRE RETARDANT (F.R.T.), U/L CERTIFIED NOW
<br />COMBUSTIBLE WHENEVER REQUIRED ALL NEW INTERIOR CONCRETE SLABS AND
<br />FOUNDATION WALLS AND FOOTINGS SHALL HAVE SOIL POISONING UNDER NEW
<br />WORK AND SHALL BE INSTALLED BY A LICENSED CONTRACTOR.
<br />17. NO COMBUSTIBLE MATERIALS ARE PERMITTED ABOVE CEILING, INCLUDING F.R.T.
<br />LUMBER.
<br />18. ALL FIRE RATED WALLS MUST HAVE RATING STENCILED IN A READILY VIEWABLE
<br />AREA, PER THE 2006 I.B.C. & NORTH CAROLINA STATE BUILDING CODE (2009).
<br />19. THERE SHALL BE NO CHANGES TO OR DEVIATIONS FROM THE REQUIREMENTS OF
<br />F.D.'S EXHIBITS OR FROM THE DRAWINGS UNLESS SUCH CHANGES OR DEVIATIONS
<br />ARE APPROVED IN WRITING BY TENANT PRIOR TO THE WORK BEING DONE.
<br />20. GC TO FIELD VERIFY AND CONFIRM ANY ROOF WORK W/ LANDLORD ON WARRANTY
<br />PRIOR TO CONSTRUCTION OR ALTERATIONS.
<br />21. ALL PLYWOOD BACKING AND ANY IMPERFECTIONS SHALL BE FILLED AND
<br />SANDED SMOOTH TO PROVIDE A CONTINUOUS SMOOTH SURFACE FOR
<br />APPLICATION OF FINISH (PAINT OR LAMINATE).
<br />22. ALL WOOD PARTITIONS WITH DOORS TO HAVE NON-COMBUSTIBLE WOOD JACK STUDS
<br />AND HEADERS.
<br />23. THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR VERIFYING AND
<br />MAINTAINING ALL EXISTING SETBACKS, EASEMENTS, AND ANY DEED RESTRICTIONS.
<br />24. THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR FINAL CLEANUP AND
<br />SHALL INCLUDE THE SITE, AND THE BUILDING. THE ENTIRE PROJECT SHALL BE
<br />LEFT IN A NEW, CLEAN CONDITION.
<br />25. THE GENERAL CONTRACTOR SHALL MEET WITH THE PLUMBING CONTRACTOR ON
<br />SITE PRIOR TO CONSTRUCTION TO VERIFY ANY AND ALL EXISTING PLUMBING
<br />CONDITIONS PERTAINING TO THIS PROJECT. MINUTES FROM THIS MEETING AND
<br />FINDINGS IN THE FIELD SHALL BE SUBMITTED TO THE ARCHITECT PRIOR TO
<br />CONSTRUCTION.
<br />26. THE GENERAL CONTRACTOR SHALL MEET WITH THE MECHANICAL CONTRACTOR ON
<br />SITE PRIOR TO CONSTRUCTION TO VERIFY ANY AND ALL EXISTING HVAC EQUIPMENT
<br />PERTAINING TO THIS PROJECT. INCLUDING EXIST. ROOF CURBS, ROOF TOP UNITS,
<br />DUCTWORK, REGISTERS, AND ANY AND ALL OTHER ON SITE MECHANICAL
<br />EQUIPMENT. MINUTES FROM THIS MEETING AND FINDINGS IN TEH FIELD SHALL BE
<br />SUBMITTED TO THE ARCHITECT PRIOR TO CONSTRUCTION.
<br />27. THE GENERAL CONTRACTOR SHALL MEET WITH THE ELECTRICAL CONTRACTOR ON
<br />SITE PRIOR TO CONSTRUCTION TO VERIFY ANY AND ALL EXISTING ELECTRICAL
<br />EQUIPMENT PERTAINING TO THIS PROJECT. INCLUDING ELECTRIC PANELS, CONDUIT,
<br />AND ANY/ALL OTHER ON -SITE ELECTRICAL EQUIPMENT, ETC. MINUTES FROM THIS
<br />MEETING AND FINDINGS
<br />IN THE FIELD SHALL BE SUBMITTED TO THE ARCHITECT PRIOR TO CONSTRUCTION.
<br />28. CLAIMS FOR CONSEQUENTIAL DAMAGES. THE ARCHITECT AND THE OWNER WAIVE
<br />CONSEQUENTAIL DAMAGES FOR CLAIMS, DISPUTES OR OTEHR MATTERS IN QUESTION
<br />ARISING OUT OF OR RELATING TO THIS PROJECT. THIS MUTAL WAIVER IS
<br />APPLICABLE, WITHOUT LIMITATION, TO ALL CONSEQUENTIAL DAMAGES.
<br />29. LANDLORD OR GC SHALL PERFORM ANY/ALL WORK REQUIRED TO CAUSE THE ENTIRE
<br />DEMISED PREMISES TO COMPLY WITH LAWS PERTAINING TO ACCESSIBILITY BY
<br />DISABLED PERSONS (ADA) AND WILL OBTAIN AND INSTALL A CERTIFICATE OF
<br />OCCUPANCY AND HEALTH CERTIFICATE (IF REQUIRED). CERTIFICATE(S) SHALL BE
<br />INSTALLED IN AN 8-1/2"X11" FRAME ON THE OUTSIDE OF THE OFFICE WALL IN A
<br />CONSPICUOUS LOCATION. THIS SHALL BE DONE PRIOR TO DELIVERING THE
<br />DEMISED PREMISES TO TENANT.
<br />30. ALL STRUCTURAL MEMBERS AND ANY EXTERIOR OPENINGS SHALL BE VERIFIED BY
<br />THE CONTRACTOR PRIOR TO CONSTRUCTION OR ALTERATIONS.
<br />31. INFILL ALL HOLES, CRACKS AND PENETRATIONS IN THE EXTERIOR WALLS.
<br />32. PROVIDE AND FACILITATE A THIRD PART INSPECTION OF ROOF W/ WRITTEN REPORT.
<br />1. THESE DRAWINGS HAVE BEEN DEVELOPED FROM
<br />6. THE CONTRACTOR SHALL VERIFY THAT EXIT EGRESS
<br />14. REMOVE EXISTING CERAMIC TILE FLOOR AND REWORK
<br />EXISTING DRAWINGS WHICH MAY NOT REFLECT
<br />IS MAINTAINED FOR ALL OCCUPIED AREAS OF THE
<br />FLOOR SLAB TO MAKE SMOOTH AND LEVEL.
<br />ACTUAL FIELD CONDITIONS. THE CONTRACTOR
<br />BUILDING THROUGHOUT ALL PHASES OF
<br />15. REMOVE EXISTING FLOORING IN SALES AREA AND
<br />SHALL VERIFY THESE DRAWINGS WITH EXISTING
<br />CONSTRUCTION.
<br />REPAIR SUB -FLOOR AS NECESSARY TO PROVIDE A
<br />FIELD CONDITIONS AND NOTIFY THE ARCHITECT
<br />IMMEDIATELY OF INCONSISTENCIES BETWEEN THESE
<br />7. DEMOLITION WORK SHALL BE EXECUTED IN
<br />SMOOTH, LEVEL SURFACE.
<br />DRAWINGS AND ACTUAL CONDITIONS BEFORE
<br />CONFORMANCE WITH ALL CODES AND ORDINANCES
<br />16. REMOVE EXISTING WALL FINISHES AND PREPARE
<br />PROCEEDING WITH CONSTRUCTION.
<br />AS SET FORTH BY ALL GOVERNING AUTHORITIES.
<br />WALLS FOR NEW WORK/FINISHES.
<br />2. THE CONTRACTOR SHALL NOTIFY THE ARCHITECT
<br />8. THE CONTRACTOR SHALL BRACE ALL EXISTING
<br />17. CAP OFF ALL PLUMBING LINES WHICH ARE NOT TO BE
<br />IMMEDIATELY IF ANY WORK INDICATED IN THE
<br />STRUCTURES AND ALL STRUCTURAL ELEMENTS AS
<br />RE -USED FLUSH WITH ADJACENT SURFACES.
<br />CONTRACT DOCUMENTS CANNOT BE PERFORMED
<br />NECESSARY DURING DEMOLITION.
<br />18. CAP OFF OR TERMINATE ALL ELECTRICAL DISTRIBUTION
<br />DUE TO EXISTING FIELD CONDITIONS.
<br />9. THE CONTRACTOR SHALL NOT CUT STRUCTURAL WORK
<br />LINES WHICH ARE NOT TO BE RE -USED FLUSH W/
<br />3. IF ANY EXISTING FIREPROOFING OR FIRE ASSEMBLIES
<br />IN A MANNER RESULTING IN A REDUCTION OF LOAD
<br />ADJACENT SURFACES.
<br />WHICH ARE SUPPOSED TO REMAIN ARE DAMAGED
<br />CARRYING CAPACITY OR LOAD/DEFLECTION RATIO.
<br />DURING DEMOLITION, THEY SHALL BE REPAIRED TO
<br />THE CONTRACTOR SHALL NOTIFY THE ARCHITECT OF
<br />19. REMOVE ALL LIGHTING FIXTURES THROUGHOUT THE
<br />CONFORM TO ORIGINAL FIRE PROTECTION
<br />ALL STRUCTURAL CUTS PRIOR TO EXECUTION SO THAT
<br />DEMISED PREMISES IN PREPARATION FOR
<br />REQUIREMENTS. CONTACT ARCHITECT TO VERIFY U.L.
<br />APPROVAL CAN BE OBTAINED FROM THE ARCHITECT
<br />INSTALLATION OF NEW F.D.S. SPECIFIED LIGHTING AS
<br />ASSEMBLIES TO BE USED FOR REPAIRS.
<br />AND STRUCTURAL ENGINEER.
<br />INDICATED IN LIGHTING SECTION.
<br />4. REMOVE EXISTING CONSTRUCTION AS INDICATED.
<br />10. THE EXISTING BUILDING ENVELOPE SHALL BE
<br />20. DEMO EXISTING HVAC IN EXISTING DEMISED PREMISES.
<br />TYPICAL WALL REMOVAL INCLUDES MECHANICAL,
<br />PLUMBING, COMMUNICATIONS, INFORMATION SYSTEMS,
<br />MAINTAINED IN WATER TIGHT CONDITION AT ALL TIMES
<br />THROUGHOUT ALL PHASES OF CONSTRUCTION.
<br />21. REMOVE ALARM PANEL AND COMPONENTS. REMOVE
<br />AND ELECTRICAL SYSTEMS CONTAINED THERE IN.
<br />EXCESS PHONE EQUIPMENT AND RELATED WIRING.
<br />REMOVE DOORS, FRAMES, FINISHES, AND OTHER
<br />11. IF THE EXISTING CONSTRUCTION IS FOUND TO CONTAIN
<br />CONTACT F.D.S. PROJ. MGR. PROJECT MANAGER TO
<br />FIXTURES AS REQUIRED. AFTER REMOVAL OF PIPE
<br />ASBESTOS, NOTIFY OWNER AND THE ARCHITECT IN
<br />DISCUSS POSSIBLE USE.
<br />CHASES, PATCH HOLES IN EXISTING FLOORS, WALLS OR
<br />WRITING. REMOVAL, DISPOSAL, AND THE
<br />ROOF. PATCH ADJOINING WALLS, FLOOR
<br />REPLACEMENT OF THE ASBESTOS MATERIAL SHALL BE
<br />IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL
<br />22 G.C. TO REMOVE EXISTING AISLE TAPE AND STRIP
<br />AND DECK. PREPARE SURFACES TO RECEIVE NEW
<br />REGULATIONS. (REPLACE THE ASBESTOS MATERIAL
<br />EXISTING FLOOR WAX.
<br />FINISH PER FINISH SCHEDULE OR PER INTERIOR
<br />DESIGNER'S FINISH PLANS. (WHERE NEW FINISHES
<br />WITH NEW MATERIAL AS APPROVED BY THE
<br />ARE CALLED FOR ON EXISTING SURFACES, REMOVE
<br />ARCHITECT.)
<br />THE EXISTING FINISH AND PREPARE SURFACE TO
<br />12. THE CONTRACTOR SHALL REPLACE OR REPAIR ANY
<br />RECEIVE THE NEW FINISH.
<br />EXISTING TO REMAIN FINISHES, ETC., WHICH ARE
<br />5. FOR EXTENT AND LOCATION OF CHANNELING OF
<br />DAMAGED DURING DEMOLITION (I.E. - CEILING TILE,
<br />EXISTING FLOOR SLABS REFER TO MECHANICAL,
<br />WALL COVERINGS, FLOOR COVERINGS, CORNER GRID,
<br />PLUMBING, FIRE PROTECTION, COMMUNICATIONS,
<br />GUARDS, WALL GUARDS, HANDRAILS, CHAIR RAILS,
<br />INFORMATION SYSTEMS, AND ELECTRICAL DRAWINGS.
<br />MOLDINGS, ETC.).
<br />IF EXISTING PIPING OR CONDUIT WORK (OTHER THAN
<br />13. REMOVE EXISTING TOILET ROOM(S) SHOWN ON THE
<br />THE DESIRED CONNECTION) IS ENCOUNTERED WHILE
<br />FLOOR PLAN AND STUB OFF ALL PLUMBING. PATCH
<br />CHANNELING, THE CONTRACTOR SHALL NOTIFY THE
<br />HOLES IN FLOOR SLAB W/ CONCRETE LEAVING A SMOOTH,
<br />ARCHITECT BEFORE CONTINUING.
<br />LEVEL SURFACE. REPAIR FLOOR COVERING TO MATCH
<br />SURROUNDING FINISH.
<br />PROJECT NOTES:
<br />1. IN -FILL HOLES/PITS IN CONCRETE SLAB TO MATCH EXISTING. G.C. TO VERIFY IN FIELD
<br />FOR LOCATION, DEPTH, AND NECESSARY IN -FILL MATERIALS/SPECIFICATIONS.
<br />2. ERECT NEW METAL STUD WALLS AND INSTALL NEW SOLID WOOD DOORS AS
<br />INDICATED ON PLAN AND IN DETAILS AND DOOR SCHEDULE.
<br />3. REPLACE FLOORING AS INDICATED ON PLAN AND IN FINISH SCHEDULE.
<br />4. INSTALL NEW DISPLAY WALL PANEL SYSTEM IN SALES AREA AS INDICATED ON PLAN
<br />AND ELEVATIONS.
<br />5. ANY AND ALL ALTERATIONS TO THE BUILDING ENVELOPE INCLUDING WALL OPENINGS,
<br />CONCRETE SLAB WORK, ROOF PENETRATIONS, ETC. SHALL BE APPROVED BY THE
<br />LANDLORD AND PERFORMED BY LANDLORD APPROVED CONTRACTOR.
<br />6. VERIFY ALL DIMENSIONS IN FIELD. NOTIFY ARCHITECT OF ANY MAJOR DEVIATIONS
<br />FROM THESE PLANS. ALL DIMENSIONS BASED ON EXISTING CONSTRUCTION ARE
<br />APPROXIMATE.
<br />7. FILL IN ANY MISSING GYP. BOARD OR PEG BOARD FROM FLOOR TO 10'-0" A.F.F. &
<br />PREP FOR NEW FINISH.
<br />8. ROOF IS EXISTING. G.C. TO FIELD VERIFY AND CONFIRM W/ LANDLORD ON WARRANTY
<br />ISSUES PRIOR TO CONSTRUCTION. NO NEW ROOF IN THIS SCOPE OF WORK.
<br />PREFERRED VENDORS:
<br />COMPANY:
<br />CONTACT:
<br />EXTERIOR & INTERIOR PAINTS:
<br />217-566-2000
<br />SHERWIN WILLIAMS
<br />EXTERIOR LIGHTS:
<br />800-933-9831 OR
<br />LITHONIA, THRU GRAYBAR ELECTRIC
<br />704-392-1804
<br />SITE LIGHTING:
<br />305-437-7975
<br />LUMINAIRE
<br />VINYL COMP. TILE:
<br />800-233-3823 ARMSTRONG)
<br />SEE FINISH SCHEDULE
<br />SEE FINISH SCHEDULE FOR ALT'S
<br />TOILET FIXTURES:
<br />800-442-1902
<br />AMERICAN STANDARD
<br />TOILET ACCESSORIES:
<br />BRADLEY (ELEC. HAND DRYER-
<br />800-272-3539
<br />"ELECTRIC-AIRE")
<br />LOCKS:
<br />SCHLAGE
<br />800-847-1864
<br />SCOPE OF WORK:
<br />CARPENTRY/ETC.
<br />STOREFRONT GLASS AND DOORS
<br />INTERIOR & EXTERIOR RENOVATION OF FORMER MERCANTILE BUSINESS
<br />VERIFY THAT EXISTING EXTERIOR DOORS (ENTRANCE AND RECEIVING) ARE IN PROPER
<br />KEY THIS SHEET).
<br />OPERATIONAL CONDITION. MAKE ANY REPAIRS NECESSARY T MAKE OPERATIONAL.
<br />INCLUDE CRASH BARS ON THE INTERIOR AND EXTERIOR OF EACH DOOR, EXTERIOR KEY
<br />IN TOILET ROOM; PROVIDE AND INSTALL T-0 WIDE SOLID CORE WOOD DOORS IN MTL.
<br />LOCK WITH INTERIOR THUMB TURN. INSTALL BRUSH STYLE DOOR SWEEPS
<br />FRAMES WITH CLOSER (YALE 4020-PAINTED) CLOSURE SHOULD NOT EXCEED ADA
<br />MANUFACTURED BY SEALEZE C380CLA06BL (X) WIDTH OF DOOR (OR APPROVED EQUAL).
<br />CODE OF 5# OPENING FORCE AND PRIVACY LOCK (SCHLAGE A40S-LEV 626), GYP.
<br />THE SHOULD BE NO LIGHT VISIBLE FROM UNDER THE DOOR OR ON THE SIDES.
<br />BOARD CEILING AND 3/4n PLYWOOD DECK ABOVE IN THE LOCATION SHOWN ON ON THE
<br />FLOOR PLAN. FURNISH ALL SCHEDULED TOILET ROOM ACCESSORIES. ALL WORK
<br />SHALL BE IN COMPLIANCE W/ LOCAL AND STATE CODES CODES. INCL. (2) TWO 3'-0 LX8"D
<br />INSTALL F.D.S. SPECIFIED WINDOW FILM PER F.D.S. FIXTURE PLAN NOTES 'OPAQUE'.
<br />(MIN.) WHITE ADJ. SHELVES OVER EA. TOILET. PROVIDE C.T. AND/OR FRP BOARD.
<br />BUDGET TO COVER ALL GLASS EXCEPT FOR 24'-0 WIDE. INSTALL TINT ON STOREFRONT
<br />GLASS UP TO 8' AFF IF THE REMAINING EXPOSED GLASS IS 11" OR MORE. OTHERWISE
<br />ALL NEW INTERIOR PARTITIONS SHALL BE CONSTRUCTED OF ONE (1) LAYER 5/8"
<br />TINT THE ENTIRE HEIGHT OF THE GLASS.
<br />GYPSUM WALL BOARD (NON -RATED) ON EACH SIDE OF 3-5/8" (20 GAUGE)
<br />PUNCHED-CEE, METAL STUD FRAMING AT 16" ON CENTER (MAXIMUM) UNLESS
<br />CLEAN ALL STOREFRONT GLASS INTERIOR AND EXTERIOR. REMOVE DECALS, LABELS
<br />NOTED OTHERWISE (FINISH AND PREPARE FOR PAINT). ALL NEW PARTITIONS
<br />AND SIGNAGE WHICH ARE NOT TO BE USED.
<br />SHALL TERMINATE 6" (MINIMUM) ABOVE HIGHEST CONTIGUOUS CEILING ASSEMBLY
<br />CEILING SYSTEMS
<br />UNLESS NOTED OTHERWISE. ALL NEW INTERIOR PARTITIONS SHALL BE
<br />NONCOMBUSTIBLE.
<br />PATCH CEILING GRID AND TILE TO PROVIDE AN UNIFORM CEILING WHERE WALLS WERE
<br />CONSTRUCT MANAGER'S OFFICE (IN RECEIVING ROOM) COMPLETE WITH WALLS (3 5/"
<br />REMOVED OR ADDED.
<br />METAL STUD FRAMING W/ 5/8" METAL STUD FRAMING W/ 5/8" FIRE RATED GYPSUM
<br />BOARD), T-O WIDE SOLID CORE WOOD DOOR W/ 180 DEGREE PEEPSITE AT 5'-0 AFF, DOOR
<br />REPLACE ALL BROKEN OR DAMAGED CEILING GRID AND ALL MISSING, STAINED OR
<br />CLOSER (YALE 4020-PAINTED) CLOSURE SHOULD NOT EXCEED ADA FORCE CODES,
<br />DMAGED CEILING TILES W/ NEW MATCHING GRID AND TILES. PAINT ENTIRE CEILING
<br />KEYED DEADBOLT W/ INSIDE THUMB TURN PROVIDE LOCK GUARD, STOREROOM
<br />'CEILING WHITE' TO PRESENT AN UNIFORM APPEARANCE..
<br />FUNCTION LEVER TYPE DOOR SET (SCHLAGE A80PD-LEV-626).
<br />REMOVE ANY EXCESS WIRES, STRINGS, CLIPS, BRACKETS, ETC. FROM CEILING.
<br />PATCH AND POINT UP EXISTING DRYWALL FINISH TO MAKE READY FOR PAINT.
<br />FLOORING
<br />FRAME AND FINISH NEW 6'X7' CASED OPENING IN RECEIVING ROOM WALL FOR NEW
<br />DOUBLE SWING DOOR.
<br />PROVIDE AND INSTALL NEW VINYL COMPOSITION TILE IN THE MAIN SALES AREA WITH
<br />ARMSTRONG #52506'RODEO FAWN' 1/8" TILE OR MANNINGTON #107 BISQUE (PROVIDE
<br />PROVIDE BLOCKING IN WALLS FOR ELECTRIC HAND DRYER AND SHELVING IN
<br />TRANSITION STRIP AS REQUIRED TO ASSURE SMOOTH TRANSITION). ENSURE THAT A
<br />BATHROOMS. LOCATION TO BE DETERMINED BY TENANT CONSTRUCTION
<br />SMOOTH SUB FLOOR IS PROVIDED. CLEAN, SEAL, WAX, AND BUFF NEW TILE IN
<br />REPRESENTATIVE.
<br />ACCORDANCE WITH TILE MANUFACTURER'S SPECIFICATIONS. ENSURE SUBFLOOR IS
<br />LEVEL, PATCHED, AND READY FOR TILE.
<br />INSTALL MONITOR BRACKET (F.D.S. SUPPLIED) VERIFY LOCATION W/ FDS
<br />REPRESENTATIVE. MOUNTING SHOULD MEET ALL STATE AND LOCAL CODES. SEE
<br />PROVIDE AND INSTALL NEW VINYL COMPOSITION FLOOR TILE IN MANAGER'S OFFICE W/
<br />ATTACHED CUT SHEET AND INSTRUCTION AND INSTRUCTION MANUAL FOR FURTHER
<br />ARMSTRONG #52506, 'RODEO FAWN' 1/8" TILE OR MANNINGTON #107 'BISQUE' (PROVIDE
<br />INFORMATION.
<br />TRANSITION STRIP AS REQUIRED TO ENSURE SMOOTH TRANSITION AT ALL OPENINGS).
<br />CLEAN, SEAL, AND BUFF.
<br />SUPPLY AND INSTALL A 96"X48"X3/4" CDX COMMUNICATIONS BOARD FOR USE BY
<br />DEMARC CONNECTION AND OUTSIDE INSTALLER. MOUNT AND SECURE BOTTOM OF
<br />PROVIDE AND INSTALL NEW VINYL COMPOSITION FLOOR TILE IN TOILET ROOMS W/
<br />BOARD AT 8'-0 AFF. BOARD SHOULD BE ABLE TO CARRY A MIN. OF 225 LBS. SEE PLANS
<br />ARMSTRONG #52506, 'RODEO FAWN' 1/8" TILE OR MANNINGTON #107'BISQUE' (PROVIDE
<br />FOR EXACT HEIGHT AND LOCATION.
<br />TRANSITION STRIP AS REQUIRED TO ENSURE SMOOTH TRANSITION AT ALL OPENINGS).
<br />CLEAN, SEAL, AND BUFF.
<br />INSTALL FRP (KELMLITE-LASCOBOARD #419 WHITE W/ EMBOSSED FINISH OR APPROVED
<br />EQUAL) ON ALL RESTROOM WALLS. INSTALL FRP BEHIND MOP SINK AND WATER COOLER
<br />PROVIDE AND INSTALL 4" ARMSTRONG #60 JET BLACK OR MANNINGTON #901 NIGHT
<br />AREAS. ALL AREAS OF FRP TO BE INSTALLED UP TO 4' ABOVE FLOOR WITH TRIM CAP ON
<br />BLACK COVE BASE ON ALL WALL SURFACES TO RECEIVE PAINT FROM FLOOR TO
<br />ALL EDGES. USE MANUFACTURED TRIM FOR JOINTS, CORNERS, AND CAPS. INCLUDE
<br />CEILING, INCLUDING ALL INTERIOR SALES FLOOR COLUMNS. CAULK AROUND EACH
<br />CAULKING AS REQUIRED. EXTEND FRP MINIMUM OF 1' BEYOND SIDES OF MOP SINK AND
<br />COLUMN ON SALES FLOOR.
<br />WATER COOLER.
<br />PROVIDE AND REPLACE STAINED, CRACKED, CHIPPED, DAMAGE OR MISSING FLOOR
<br />PROVIDE AND INSTALL 1"X4" WOOD FURRING STRIPS AT ALL SALES AREA WALLS.
<br />TILES THROUGHOUT THE DEMISED PREMISES WITH MATCHING TILES. PROVIDE
<br />FURRING STRIPS SHALL BE INSTALLED AT 6'-0 AFF AROUND THE PERIMETER OF THE
<br />MATCHING TILE SAMPLE FOR APPROVAL TO THE FDS CONTT. MANAGER. CLEAN, STRIP,
<br />SALES AREA WALLS. PAINT WOOD FURRING STRIPS TO MATCH SALES AREA WALL.
<br />SEAL, WAX AND BUFF ENTIRE FLOOR.
<br />PROVIDE 10 ADDITIONAL 1 "X4"X8'PAINTED FURRING STRIPS. FURRING STRIPS ARE TO
<br />REMAIN IN STORE FOR FUTURE USE.
<br />REMOVE EXIST, WALL FINISHES AND PREPARE WALL FOR NEW FINISHES.
<br />DOORS AND HARDWARE
<br />CLEAN, STRIP, SEAL, WAX AND BUFF ALL FLOOR TILE IN SALES AREA, MANAGER'S
<br />OFFICE, AND RESTROOMS.
<br />PROVIDE AND INSTALL A NEW TXT ELIASON DOUBLE SWING RECEIVING ROOM DOOR
<br />(MODEL #LWP3-PR72X84FD).
<br />REPAIR AND RE -SEAL CONCRETE FLOOR W/ CLEAR ACRYLIC SEALER.
<br />INSTALL ARM-A-DOR-MODEL #A10X-XXX (X-XXX DETERMINED BY WIDTH OF DOOR AND
<br />SEAL RECEIVING ROOM FLOOR WITH CLEAR ACRYLIC SEALER.
<br />DOOR JAM) SECURITY ALARM AND BAR (F.D.S. SUPPLIED) ON EXISTING EXTERIOR
<br />FREIGHT RECEIVING DOOR (CONTACT 704-334-8683 FOR INFORMATION).
<br />FILL ANY EXTING COOLER/FREEZER TRENCHES AND MOUNTING POINTS IN SALES FLOOR
<br />AND PROVIDE A SMOOTH LEVEL SURFACE.
<br />WALLS/PAINTING
<br />SPECIFICATIONS
<br />GENERAL
<br />MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS ARE DIAGRAMMATIC AND ARE
<br />NOT BASED ON A SITE VISIT. CONTRACTOR TO FURNISH AND INSTALL ALL ITEMS
<br />AIPf`PCCADV =r)D A r nRAD1 I=TG GIRCT r`I ACC IAICTAI I ATir)KI r)P TWAT ARP PCCPAITIAI
<br />.----- ------ .-- -------------. - -- - -- - - -
<br />--
<br />FOR PROPER OPERATION OF WORK INDICATED.
<br />ALL WORK ON THIS PROJECT SHALL CONFORM TO THE REQUIREMENTS OF THE
<br />'GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION DOCUMENT A201
<br />FIFTEENTH ED, 1997 AND ARE HEREBY MADE A PART OF THESES SPECIFICATIONS SD
<br />IF BOUND HEREIN AND SHALL APPLY TO ALL DIVISIONS AS THOUGH COPIES IN EACH.
<br />CONTRACTOR IS RESPONSIBLE FOR MEANS AND METHODS OF CONSTRUCTION TO
<br />ENSURE THE SAFETY OF THE BUILDING UNTIL STRUCTURAL SYSTEM IS COMPLETED.
<br />THIS INCLUDES BUT NOT LIMITED TO, THE ADDITION OF WHATEVER TEMPORARY
<br />BRACING, SHORING, GUYS OR TIE DOWNS THAT MAY BE NECESSARY. SUCH MATERIAL
<br />SHALL BE REMOVED AND SHALL REMAIN THE PROPERTY OF THE CONTRACTOR AFTER
<br />THE COMPLETION OF THE PROJECT.
<br />SHOP DRAWINGS AND SAMPLES
<br />CONTRACTOR TO PROVIDE OWNER SAMPLES FOR APPROVAL OR PRODUCT
<br />LITERATURE PRIOR TO ORDERING AND OR FABRICATION OF THE FOLLOWING:
<br />A. DOORS AND DOOR HARDWARE.
<br />B. WIDOWS, STOREFRONT, AND FINISHES.
<br />C. ELECTRICAL EQUIPMENT.
<br />D. HVAC EQUIPMENT.
<br />E. PLUMBING FIXTURES.
<br />VERIFICATION OF FIELD MEASUREMENTS OR CONDITIONS SHALL REMAIN THE
<br />RESPONSIBILITY OF THE CONTRACTOR.
<br />PROJECT CLOSE-OUT
<br />UPON COMPLETION OF THE WORK UNDER THIS CONTRACT AND BEFORE FINAL PAYMENT
<br />WILL BE MADE, SUBMIT THE FOLLOWING ITEMS TO THE OWNER:
<br />A. SUBMIT ONE COPY OF PROJECT RECORD DOCUMENTS TO OWNER REDLINING
<br />SIGNIFICANT CHANGES NOT SHOWN ON THE ORIGINAL DOCUMENTS ONTO A SET
<br />OF REPRODUCTIONS.
<br />B. SUBMIT PROPERLY EXECUTED RELEASE OF LIEN FROM ALL SUBCONTRACTORS
<br />AND MATERIAL SUPPLIERS CONTAINING ORIGINAL SIGNATURES AND RAISED
<br />NOTARY SEAL.
<br />C. CERTIFICATE OF OCCUPANCY FROM APPLICABLE GOVERNMENT AGENCY.
<br />D. WARRANTY CERTIFICATES AS CALLED FOR IN INDIVIDUAL SECTIONS
<br />OF SPECIFICATIONS.
<br />E. LETTER CERTIFYING THE DELIVERY OF ALL KEYS TO THE OWNER.
<br />F. LETTER CERTIFYING THAL ALL ITEMS ON THE FINAL PUNCH LIST HAVE BEEN
<br />COMPLETED OR CORRECTED.
<br />G. LIST OF ALL SUBCONTRACTORS INCLUDING ADDRESSES AND TELEPHONE
<br />NUMBERS.
<br />H. CLOSEOUT/MAINTENANCE MANUAL DETAILING THE PROCEDUDURES REQUIRED
<br />FOR PROPER CARE AND MAINTENANCE OF ALL EQUIPMENT FURNISHED UNDER
<br />THE CONTRACT.
<br />PAINT A 1'-0 WIDE WHITE STRIPE ON PERIMETER FLOOR IN THE RECEIVING ROOM A
<br />MINIMUM OF 2 COATS OF SHERWIN WILLIAMS #7006'EXTRA WHITE' PROGREEN 200 S/G
<br />B31 W651 SEMI -GLOSS.
<br />SHEETROCK AND FINISH ANY MISSING AREAS BEHIND THE COOLERS ON THE SALES
<br />FLOOR.
<br />EXTERIOR/ROOF
<br />PRESSURE WASH THE FRONT OF THE BUILDING REMOVING ALL DEBRIS.
<br />PROVIDE AND FACILITATE A THIRD PARTY INSPECTION OF THE ROOF W/ A WRITTEN
<br />REPORT.
<br />SEAL ALL HOLES LEADING FROM THE OUTSIDE TO THE INSIDE OF THE SPACE. INCLUDING
<br />AROUND ALL PIPES AND WIRE RUNS CAP OFF AND SEAL ANY OPEN PIPES.
<br />PROJECT RECORD DOCUMENTS
<br />MAINTAIN AT THE JOB SITE ONE COPY OF ALL CONTRACT DOCUMENTS, 'IMPROVEMENTS
<br />BY FAMILY DOLLAR', AND 'IMPROVEMENTS BY LANDLORD' DOCUMENTS.
<br />SUBMIT PROJECT RECORD DOCUMENTS TO THE ARCHITECT UPON COMPLETION OF THE
<br />PROJECT AND PRIOR TO FINAL PAYMENT.
<br />FINISHES (PAINT)
<br />UNLESS OTHERWISE INDICATED ON THE DRAWINGS, PAINTED SURFACES SHALL RECEIVE
<br />THE FOLLOWING COATS AND TYPE OF PAINT. APPLY PAINT BY BRUSH, ROLLER, OR
<br />SPRAY, EXCEPT MASONRY SURFACES, CEMENT, PLASTER, OR CONCRETE BLOCK SHALL
<br />BE APPLIED BY BRUSH OR APPLIED BY BRUSH OR AIRLESS SPRAY ONLY.
<br />A. GYPSUM WALLBOARD (SMOOTH FINISH)
<br />ONE (1) COAT SHERWIN WILLIAMS UNDERCOAT
<br />TWO (2) COATS PAINT.
<br />PRE -PAINTING AND DECORATING:
<br />MEET AT THE PROJECT SITE WITH ALL TRADES AND F.D.S. PROJ. MGR. REVIEW
<br />CONDITIONS OF SUBSTRATES WITH DRYWALL INSTALLERS PRIOR TO APPLICATION OF
<br />ANY PAINTS.
<br />REVIEW WITH F.D.S. PROJ. MGR. TO DISCUSS DECORATIVE PAINTING AND ANY
<br />CONDITIONS WHICH WOULD POSSIBLY INTERFERE WITH SUCCESSFUL PAINTING AND
<br />DECORATING OF THE AREA AS WORK OF THIS SECTION.
<br />CLOSED SPEC PROVIDERS:
<br />COMPANY:
<br />CONTACT:
<br />EMS - LIGHTING CONTROL SYSTEM:
<br />H.P. 800-518-6630 EXT. 3258
<br />HILL PHOENIX & LIGHTSAT
<br />L.S. 800-292-2444 EXT. 221
<br />HVAC UNITS:
<br />615-986-1533 (BOB FURSTENBERG)
<br />CARRIER
<br />HVAC UNITS:
<br />405-419-6535 (LISA KUHNS)
<br />YORK
<br />MOTION SENSOR SYSTEM EXTERIORS:
<br />800-933-9831 OR
<br />GRAYBAR
<br />704-392-1804
<br />SALES FLOOR DOOR:
<br />800-828-3655
<br />ELIASON DOORS
<br />SECURITY DOOR HARDWARE:
<br />704-334-8683 COOK & BOARDMAN
<br />ARM -A -DOOR
<br />FLOOR PRODUCT FIXTURES:
<br />FLOOR PRODUCT FIXTURES
<br />LOZIER BY FDS
<br />LOZIER BY FDS
<br />CHECK OUT FIXTURES:
<br />CHECK OUT FIXTURE
<br />LYONS BY FDS
<br />LYONS BY FDS
<br />POWER POLE CONNECTIONS:
<br />800-251-2200 OR
<br />D & P CUSTOM LIGHTS
<br />615-350-7800
<br />INTERIOR LIGHTS:
<br />800-933-9831 OR
<br />LITHONIA, THRU GRAYBAR ELECTRIC
<br />704-392-1804
<br />VINYL COMP. TILE:
<br />800-233-3823 (ARMSTRONG)
<br />SEE FINISH SCHEDULE
<br />SEE FINISH SCHEDULE FOR ALT'S
<br />PRO TINT INC:
<br />800-553-8693 (CHRIS LUECK)
<br />SEE FINISH SCHEDULE
<br />POWER POLE LIST:
<br />TYPE
<br />ITEM #
<br />QTY.
<br />CHECKOUT -12
<br />8010130
<br />2
<br />UNICRU -16
<br />8529433
<br />1
<br />EAS -16
<br />8520242
<br />1
<br />AISLE - 8'
<br />8529487
<br />1
<br />COKE -12'
<br />8010130
<br />1
<br />COOLERS -15'
<br />8529498
<br />1
<br />SEC. MONITOR
<br />8529498
<br />1
<br />NOTE:
<br />POWER POLE SHALL BE ORDERED AND
<br />INSTALLED FOR STORES THAT OPEN
<br />WITH COOLERS & READY FOR COOLERS.
<br />PIGTAIL LIST:
<br />QTY & ITEM # OF D & P PLUGS
<br />2 GREEN (ID4-IG) & 2 BROWN (ID3)
<br />1 GREEN (ID44G)
<br />1 GREEN (I1344G)
<br />1 BROWN (ID3)
<br />1 BROWN (ID3)
<br />FREEZER & COOLER - BROWN (642FDS005)
<br />ADD FOR SINGLE PHASE WHIP IDB-35FT. (624FDS007)
<br />MONITOR PLUG BROWN WITH DUPLEX (000MW054F)
<br />NOTE:
<br />1. ALL POWER IS TO BE DROPPED FROM CEILNG AT LOCATION
<br />SPECIFIED ON PLAN.
<br />2. ELECTRICAL LOCATIONS MUST BE VERIFIED BY FDS PROJECT
<br />MANAGER PRIOR TO INSTALLATION.
<br />FIXTURE NOTES:
<br />--------------------
<br />RISERS & 6" EXTENDERS
<br />PERMITTED THIS AREA
<br />L J
<br />WALLS RECEIVE 12"
<br />EXTENDERS & PEG
<br />STORE OPENER TO INSTALL EXTENDERS
<br />FOR HBA GONDOLAS. RISER SHELVES
<br />TO BE INSTALLED ONLY IF SPECIFIED IN
<br />THE INSTRUCTIONS FOUND IN THE STORE
<br />OPENING PACKAGE.
<br />NOTE:
<br />LOCATION OF MAIN CIRCULATION AISLES IS APPROXIMATE
<br />AND SUBJECT TO APPROVAL BY TENANT REPRESENTATIVE.
<br />PLACEMENT, NUMBER, & TYPE OF FIXTURES ALSO SUBJECT
<br />TO APPROVAL BY TENANT REPRESENTATIVE. REFERENCE
<br />FIXTURE PLAN FROM FAMILY DOLLAR STORE OFFICE FOR
<br />ACTUAL FIXTURE LOCATIONS.
<br />ALL FIXTURES ARE SUPPLIED BY TENANT & INSTALLED BY
<br />G.C.
<br />FLOOR FINISH NOTES:
<br />1. G.C. SHALL REMOVE EXISTING AISLE TAPE.
<br />2. G.C. SHALL STRIP EXISTING FLOOR WAX.
<br />3. G.C. SHALL APPLY 3 COATS OF FLOOR WAX
<br />UPON COMPLETION. COORD. SCHEDULE
<br />W/ FDS REPRESENTATIVE.
<br />UTILITIES
<br />NOTE:
<br />GC TO PROVIDE TEMPORARY UTILITIES TO SPACE. F.D.S. WILL
<br />PROVIDE PERMANENT POWER FOR TRANSFER AT COMPLETION
<br />OF CONSTRUCTION AND POSSESSION OF SPACE BY FDS.
<br />LANDLORD WORK/NOTES:
<br />1. REFER TO 'IMPROVEMENTS BY LANDLORD' SPECS - SEE F.D.S. PROJECT MANAGER
<br />2. ANY AND ALL ALTERATIONS TO THE BUILDING ENVELOPE INCLUDING WALL OPENINGS
<br />CONCRETE SLAB WORK, ROOF PENETRATIONS, ETC. SHALL BE APPROVED BY THE
<br />LANDLORD AND PERFORMED BY LANDLORD APPROVED CONTRACTOR.
<br />3. NO STRUCTURAL WORK OF ANY KIND (INCLUDING, BUT NOT LIMITED TO: CUTTING,
<br />PATCHING, SPLICING, WELDING, OR SUSPENDING MATERIALS OR ITEMS OF
<br />CONSTRUCTION FROM EXISTING STRUCTURAL COMPONENTS) SHALL BE
<br />UNDERTAKEN BY GENERAL CONTRACTOR OR HIS SUBCONTRACTORS WITHOUT
<br />EXPRESS WRITTEN APPROVAL OF LANDLORD.
<br />4. LANDLORD TO INSURE ALL UTILITIES ARE SEPARATELY METERED TO THE F.D.S.
<br />DEMISED SPACE.
<br />5. REMOVE ALL ASBESTOS CONTAINING MATERIALS AS REQ'D BY CODE. PROVIDE TO
<br />FAMILY DOLLAR A CLOSURE LETTER STATING THAT TO THE BEST OF YOUR KNOW-
<br />LEDGE THE SPACE IS FREE OF ASBESTOS.
<br />6. PLACE EXIST. STOREFRONT, CANOPY/MANSARD IN GOOD REPAIR. MAKE REPAIRS TO
<br />ROOF, FLASHING, GUTTERS & DOWNSPOUTS AS REQ'D TO PUT IN WATERTIGHT CONDITION.
<br />o
<br />o a
<br />a) N 0)
<br />rn EE
<br />.0
<br />�
<br />� N 8
<br />\./ co I' v
<br />c
<br />�Lj W 75 16
<br />a) a)
<br />�-- =3 U c
<br />�O
<br />>
<br />OMi N
<br />4zrn c
<br />,w
<br />•�-�i
<br />c cD
<br />U o0
<br />o --
<br />r-
<br />ISSUED FOR REVIEW
<br />DATE:
<br />ISSUED FOR PERMIT
<br />DATE:
<br />ISSUED FOR CONSTRUCTION
<br />DATE:
<br />z
<br />0
<br />a
<br />U
<br />w
<br />0
<br />w
<br />w
<br />a
<br />CV
<br />0 �
<br />U- M
<br />u-
<br />J
<br />m
<br />J
<br />J �
<br />o04 a
<br />z coo N
<br />DATE: 1.6.11
<br />DRAWN BY:
<br />PDL
<br />CHECKED BY:
<br />PDL
<br />SHEET
<br />Gwl
<br />Imo- u a _ uu 1.1,iE J tJ 11111;1. A i.. _i 1s I I
<br />
|