|
DIVISION S FINISHES
<br />DIVISION S FINISHES (CONT.)
<br />DIVISION S FINISHES (CONT.)
<br />DIVISION lO SPECIALTIES
<br />SECTION 09110 METAL SYSTEMS
<br />SECTION 09511 ACOUSTIC PANEL CEILINGS
<br />SECTION 10522 FIRE EXTINGUISHERS
<br />METAL STUDS
<br />PART I GENERAL
<br />SECTION OSS60 STUCCO FINISH
<br />PARti GENERAL
<br />A. AT INTERIOR METAL STUD PARTITIONS, UNLESS OTHERWISE SHOWN ON THE DRAWINGS, PROVIDE
<br />1,01 GENERAL
<br />PART i GENERAL
<br />1.01 SUBMITTALS
<br />STANDARD PUNCH STEEL STUDS OF THE SIZES SHOWN ON THE DRAWINGS, EITHER HOT -DIP
<br />q, COORDINATE LAYOUT AND INSTALLATION OF AGOUSTICAL CEILING UNITS AND SUSPENSION SYSTEM
<br />A. PRODUCT DATA: REQUIRED
<br />GALVANIZED OR FACTORY PRE -PAINT: 25 GA. UNLE55 SHOWN OTHERWISE ON THE DRAWINGS, 20
<br />COMPPONENTS WITH OTHER CONSTRUCTION THAT PENETRATES CEILINGS OR IS SUPPORTED BY THEM,
<br />1.01 SUMMARY
<br />B. SHOP DRAWINGS: NOT REQUIRED
<br />GA. AT ALL DOOR OPENINGS.
<br />INCLUDING LIGHT FIXTURES AND HVAC EQUIPMENT.
<br />A. MATERIALS AND INSTALLATION OF CEMENT STUCCO ON HOLLOW MASONRY, EXTERIOR GRADE PLYWOOD AND
<br />C. SAMPLES: NOT REQUIRED
<br />B. ACCESSORIES: PROVIDE ALL ACCESSORIES INCLUDING, BUT NOT NECESSARILY LIMITED T0,
<br />METAL LATH ALSO FURNI5W AND INSTALL METAL, LATH, STUCCO WRAP AND ACCESSORIES.
<br />TRACKS, CLIPS, ANCHORS, FASTENING DEVICES, SOUND ATTENUATION PENCIL RODS AND
<br />122 MINERAL -FIBER ACOUSTICAL PANELS
<br />PART 2 PRODUCTS
<br />RESILIENT CLIPS, AND OTHER ACCESSORIES REQUIRED FOR A COMPLETE AND PROPER
<br />A. PROVIDE ACOUSTICAL PANELS AS MANUFACTURED BY ARMSTRONG CIRRUS ANGLED TEGULAR
<br />1.02 DELIVERY, STORAGE AND HANDLING
<br />INSTALLATION, AND AS RECOMMENDED BY THE MANUFACTURER OF THE STEEL 5TUD5 USED,
<br />24 INCHES BY 24 INCHES 3/4 INCHES THICK WHITE, REFER TO DRAWINGS FOR- LIMITS OF TILE
<br />A. DELIVER ALL CEMENT MATERIALS IN ORIGINAL CONTAINERS BEARING MANUFACTURERS NAME AND
<br />2.01 MANUFACTURERS/PRODUCTS
<br />C. MEET OR EXCEED MINIMUM REQUIREMENTS OF FEDERAL SPEC. QQ-S-698 AND FEDERAL SPEC.
<br />INSTALLATION.
<br />IDENTIFICATION.
<br />A. COORDINATE WITH LOCAL MUNICIPALITIES AND PROVIDE FIRE EXTINGUISHERS.
<br />QQ-S 115D, CLASS D.
<br />B, INSTALL IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS. ARRANGE
<br />B. DELIVER NEW, FLAT STRUCTURAL METAL LATH IN ORGINAL PACKAGING.
<br />B. FIRE EXTINGUISHERS: SEE DRAWINGS FOR SPECIFICATIONS.
<br />METAL TRIM
<br />ACOUSTICAL UNITS AND ORIENT DIRECTIONAL PATTERN OF TILES FOR A UNIFORM APPEARANCE. REST
<br />C. PROTECT PRODUCTS FROM MOISTURE AND HUMIDITY. STORE UNDER COVER OFF GROUND IN A DRY
<br />A. FORM FROM GALVANIZED STEEL NOT LIGHTER THAN 26 GAUGE, COMPLYING WITH FEDERAL SPEC
<br />PANELS ON FLANGES OR INVERTED TEES WITH TILE UNITS FITTING NEATLY AGAINST BUTTING SURFACE
<br />LOCATION.
<br />PART 3 EXECUTION
<br />00-6-115, CLASS D.
<br />AND SUPPORT BY WALL ANGLES.
<br />B, CASING BEADS: U.S.G. "200-5.
<br />1.03 SUBMITTALS
<br />3.01 SCHEDULES
<br />1.03 METAL SUSPENSION SYSTEM
<br />A. MANUFACTURERS SPECIFICATION AND PRODUCT DATA FOR STUCCO APPLICATIONS.
<br />A. INSTALL AS REQUIRED.
<br />END OF SECTION 09110
<br />A, PROVIDE SYSTEM AS MANUFACTURED BY ARMSTRONG SUSPENSION SYSTEM SHALL BE EXPOSED
<br />B. STUCCO WRAP STRUCTURAL METAL LATH AND ACCESSORIES, SUCH AS CORNER BEAD, CONTROL JOINTS, ETC.
<br />TEE -GRID, DOUBLE -WEB, INTERMEDIATE DUTY (ASTM C635), ELECTROGALVANIZED, COLD -ROLLED STEEL,
<br />END OF SECTION 10522
<br />15/16 INCHES WIDE, CAPPED BOTTOM FLANGE. WHITE IN COLOR SYSTEM TO INCLUDE ALL CRO55 TEES,
<br />SECTION OB250 GYPSUM WALLBOARD
<br />BRIDGING TREES, INTERSECTION CLIPS, SPLICES, COMPLETE EXPOSED GRID SYSTEM.
<br />SECTION 10800 TOILET ACCESSORIES
<br />B, LAY OUT PATTERN IN ACCORDANCE WITH THE DRAWINGS, LEVEL, TRUE TO PLANE, AND AT THE REQUIRED
<br />PART 2 PRODUCTS
<br />PART I GENERAL
<br />ELEVATION, FRAME AROUND ALL OPENINGS IN CEILING LIGHTS AND GRILLES WITH MAIN RUNNERS. HANGERS
<br />PARt 1 GENERAL
<br />ARE TO BE SPACED AT 4'-0" ON CENTER MAXIMUM. PROVIDE ADDITIONAL HANGERS AS REQUIRED TO
<br />2.01 JOB MIXED INGREDIENTS
<br />1.01 GENERAL
<br />SUPPORT LIGHT FIXTURES AND HVAC REGISTERS AND GRILLES AND INTERFERENCES OF DUCT WORK.
<br />A. PORTLAND CEMENT, ASTMC 150 TYPE I, MIXED IN ACCORD WITH MANUFACTURERS INSTRUCTIONS.
<br />1.01 SUBMITTALS
<br />A. GYPSUM WALLBOARD WOW SHALL CONFORM TO THE GYPSUM ASSOCIATION "RECOMMENDED
<br />B. WATER: CLEAN AND POTABLE.
<br />A. PRODUCT DATA: NON -REQUIRED
<br />SPECIFICATIONS FOR THE APPLICATION AND FINISHING OF GYPSUM WALLBOARD."
<br />C. SECURES WIRES BY LOOPING AND WIRE -TYING, EITHER DIRECTLY TO STRUCTURES OR TO INSERTS, EYE
<br />C. METAL LATH
<br />B. SHOP DRAWINGS: NON -REQUIRED
<br />B. EXAMINE SUBSTRATES TO WHICH DRY WALL CONSTRUCTION ATTACHES OR ABUTTS, PRESET HOLLOW METAL
<br />SCREWS, OR OTHER DEVICES APPROPRIATE FOR SUBSTRATE. SCREW ATTACH EDGE MOLDINGS TO
<br />1, STRUCTURAL METAL LATH SHALL BE 3.4 POUND EXPANDED METAL SHEET WITH SOLID PARALLEL RIBS.
<br />C. SAMPLES: NON -REQUIRED
<br />FRAMES, CAST-IN-ANCORS, AND STRUCTURAL FRAMING FOR COMPLIANCE WITH REQUIREMENTS FOR
<br />SUBSTRATE AT INTERVALS NOT OVER 16 INCHES ON CENTER AND NOT MORE THAN 3 INCHES FROM ENDS.
<br />2,. METAL LATH SHALL BE 3.4 POUND DIAMOND MESH METAL LATH.
<br />INSTALLATION TOLERANCE AND OTHER CONDITIONS AFFECTING PERFORMANCE OF DRY WALL
<br />LEVEL GRID TO A TOLERANCE OF 1/8" IN 12 FEET.
<br />3. ACCESSORIES FURNISHED BY SAME MANUFACTURER FOR STUCCO APPLICATION.
<br />PART 2 PRODUCTS
<br />CONSTRUCTION. DO NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN
<br />D. MECHANICAL FASTENERS
<br />CORRECTED.
<br />END OF SECTION 095ll
<br />I. NAILS, 8d RING SHANK, HOT DIP GALVANIZED OF SUFFICIENT LENGHTH TO PENETRATE PLYWOOD BACKING
<br />2.01 MANUFACTURERS/PRODUCTS
<br />C. DO NOT TAPE AND FINISH GYPSUM BOARD WHEN THE TEMPERATURE 15 BELOW 60 DEGREES FAHRENHEIT,
<br />I INCH,
<br />A. ACCESSORIES SHALL BE AS MANUFACTURED BY "BRADLEY" OR EQUAL BY "BOBRICK." SEE DRAWINGS
<br />THE TEMPERATURE OF THE ROOMS SHALL BE HELD AT 60 DEGREES FAHRENHEIT FOR 48 HOURS BEFORE
<br />SECTION 0%50 VINYL COMPOSITION TILE
<br />2, WHERE LIGHT METAL FRAMING OCCURS: MINIMUM NOlo SELF DRILLING CORROSION RESISTANT SCREWS OF
<br />FOR SPECIFICATIONS.
<br />TAPING AND FINISHING IS TO BEGIN, MAINTAIN 60 DEGREES FAHRENHEIT DURING AND AFTER INSTALLATION,
<br />SUFFICIENT LENGTH TO PENTRATE METAL 3/8 INCH,
<br />VENTILATES AS REQUIRED TO REMOVE EXCESS HUMIDITY.
<br />PART I GENERAL
<br />E. STUCCO WRAP
<br />PART 3 EXECUTION
<br />1. BY "TYVEK" FOR USE OVER PLYWOOD AND/OR DENSGLASS FACINGS/SHEATHINGS.
<br />122 GYPSUM WALLBOARD
<br />1.01 SUMMARY
<br />F. STUCCO ACCESSORY TRIM, BEADS, AND CONTROL JOINTS SHALL BE VINYL.
<br />3.01 SCHEDULES
<br />A. GYPSUM WALLBOARD SHALL BE MANUFACTURED BY U.S. GYPSUM. WALLBOARD fS TO MEET. ASTM C36-84A
<br />A. PROVIDE TYPE AND STYLE AS SCHEDULED IN THE FINISH MATERIAL SCHEDULE.
<br />A. COORDINATE WITH DRAWINGS.
<br />AND 55-L-30d 1/2 INCHES THICK, 48 INCHES WIDE WITH TAPERED EDGES.
<br />B. ADHESIVES,
<br />PART 3 EXECUTION
<br />B. AT FIRE RATED PARTITIONS INSTALL WALLBOARD TO MEET SEPARATE REQUIREMENTS, USE TYPE III, GRADE
<br />I. PROVIDE WHITE LATEX CARPET ADHESIVE SUCH AS W.W. HENRY COMPANY NO 356, ROBERTS
<br />END OF SECTION 10000
<br />X CLASS I, 5/8 INCHES THICK FIRE RETARDANT WALLBOARD.
<br />COMPANY NO, 41-0504, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED
<br />3,01 INSTALLATION
<br />SECTION IOWO MISCELLANEOUS SPECIALTIES
<br />C. INSTALL GYPSUM BOARD WITH TRUE, EVEN SURFACES AND STRAIGHT, SHARP CORNERS, USE !FULL LENGTH
<br />FOR THE PURPOSE BY THE MANUFACTURER OF THE SELECTED CARPET,
<br />A. INSTALL MECHANICAL FASTENERS ON 6 INCH CENTERS ALONG SEAMS AND 12 INCH CENTERS ALONG
<br />BOARDS WHERE POSSIBLE. END JOINTS ON THE SAME SIDE OF A WALL SHALL BE STAGGERED AND JOINTS
<br />2. PROVIDE SEAM ADHESIVE SUCH AS W.W. HENRY COMPANY NO, 246, ROBERTS COMPANY NO.
<br />INTERIORS.
<br />PART I GENERAL
<br />ON OPPOSITE SIDE SHALL NOT OCCUR OVER THE SAME SUPPORT. DO NOT LOCATE NORMAL END JOINTS AT
<br />41-0502, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED FOR THE PURPOSE
<br />B. STUCCO INSTALLATION SHALL BE TWO COAT APPLfCATION. APPLY BASE COAT WITH FIRM PRESSURE TO
<br />EDGE OF OPENINGS. FORM JOINTS NEATLY. BUTT BOARDS TOGETHER BUT DO NOT FORCE INTO PLACE. DO
<br />BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />FORM GOOD BOND THEN DOUBLE BACK TO PROVIDE THICKNESS. LEAVE ROUGH ENOUGH TO PROVIDE BOND
<br />1.01 RELATED DOCUMENTS
<br />NOT BUTT EDGES AGAINST TAPERED EDGES. NO JOINT SHALL HAVE A GAP GREATER THAN 1/4 INCH.
<br />C. AT INTERSECTION OF CARPET AND FLOOR TILE, PROVIDE ROPPE COMPANY, INC. VINYL TILE CARPET JOINER
<br />FOR FINISH COAT. FINISH COAT SHALL BE OF TEXTURE AS CALLED FOR ON THE BUILDING ELEVATION
<br />A. REQUIREMENTS OF DIVISION I APPLY TO ALL WORK HEREUNDER.
<br />D. IN GENERAL, INSTALL GYPSUM BOARD ON CEILING BEFORE WALLS. CONSTRUCT CEILINGS WITH LONG
<br />"I88 OR EQUIVALENT.
<br />DRAWINGS,
<br />DIMENSION OF GYPSUM BOARD APPLIED AT RIGHT ANGLES TO SUPPORT.
<br />D. PROVIDE OTHER MATERIALS, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A COMPLETE AND
<br />C. CURING: CURE STUCCO BY USE OF POLYETHYLENE FILM, OR BY USE OF FINE SPRAY.
<br />1.02 SCOPE
<br />E. SCREW GYPSUM BOARD TO FRAMING WITH SCREWS NOT OVER 6 INCHES ON CENTER FASTEN GYPSUM
<br />PROPER INSTALLATION, AS SELECTED BY THE CONTRACTOR, SUBJECT TO THE APPROVAL OF THE
<br />A. PROVIDE MISCELLANEOUS SPECIALTIES AND RELATED ITEMS AS REQUIRED TO COMPLETE WORK
<br />BOARD BEGINNING AT THE CENTER AND WORK TOWARDS OUTER EDGES. HOLD BOARD FIRMLY AGAINST
<br />ARCHITECT.
<br />3,02 PROTECTION
<br />INDICATED ON DRAWINGS AND SPECIFIED HEREIN.
<br />WOOD FRAMING WHILE FASTENING. FASTENERS AT EDGES OF BOARDS SHALL BE 1/2 INCH FROM THE EDGE,
<br />E. ALLOW THE OWNER TO INSPECT AND SELECT FROM SCRAP CARPET REMAINING AFTER THE INSTALLATION.
<br />A. PROTECT STUCCO DURING AND UPON COMPLETION FROM WATER INFILTRATION, DUST, [DIRT, PRECIPITATION,
<br />F. OPENINGS FOR ELECTRICAL DEVICES, PIPING, GRILLS, AND REGISTERS SHALL BE ACCURATELY LOCATED
<br />BUNDLE, WRAP IN BURLAP, AND DELIVER TO THE OWNER THE CARPET SCRAPS 50 SELECTED.
<br />EXCESSIVE DRYING UNTIL STUCCO HAS SET.
<br />1.03 QUALITY ASSURANCE
<br />AND NEATLY MADE TO CLOSELY FIT THE DEVICES AND BE COMPLETELY COVERED BY PLATES AND
<br />A. FIELD MEASUREMENTS: TAKE FIELD MEASUREMENTS PRIOR TO PREPARATION OF SHOP DRAWINGS
<br />ESCUTCHEONS.
<br />END OF SECTION 09960
<br />AND FABRICATION WHERE NECESSARY TO ENSURE PROPER FITTING OF WORK,
<br />SECTION 09680 CARPETING
<br />B. B. INSERTS AND ANCHORAGE'S: FURNISH INSERTS AND ANCHORING DEVICES WHICH MUST BE SET IN
<br />123 TRIM PIECES
<br />CONCRETE OR MASONRY FOR INSTALLATION OF UNIT. PROVIDE SETTING DRAWINGS, TEMPLATES,
<br />A. PROVIDE TRIM ACCESSORIES OF THE SIZES REQUIRED FOR THE WALLBOARD APPLICATION AS
<br />PART i GENERAL
<br />INSTRUCTIONS AND DIRECTIONS FOR INSTALLATION OF ANCHORAGE DEVICES. COORDINATE
<br />MANUFACTURED BY U.S. GYPSUM. PROVIDE DUR-A-BEAD CORNER BEAD AT EXTERNAL CORNERS AND NO,
<br />DELIVERY WITH OTHER WORK TO AVOID DELAY.
<br />200-A METAL CASING BEAD WHERE WALLBOARD ABUTTS OTHER MATERIALS.
<br />IDI CARPETING
<br />PART 2 PRODUCTS
<br />A. PROVIDE TYPE AND STYLE AS SCHEDULE[) IN THE FINISH MATERIAL SCHEDULE,
<br />124 FASTENERS
<br />B. ADHESIVES.
<br />2.01 MANUFACTURERS/PRODUCTS
<br />A. PROVIDE SCREWS, NAILS, CLIPS, TIES, AND OTHER FASTENERS AS RECOMMENDED BY THE GYPSUM
<br />1. PROVIDE WHITE LATEX CARPET ADHESIVE SUCH AS W.W. HENRY COMPANY NO 356, ROBERTS
<br />A. MFRS' NAMES AND PRODUCT NUMBERS LISTED IN SPECIALTIES SCHEDULE ARE FOR DESCRIPTIVE
<br />MANUFACTURER
<br />COMPANY NO.41-0504, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED
<br />PURP05E AND ALL, UNLESS SPECIFICALLY PROHIBITED THEREIN, SHALL BE SUBJECT
<br />FOR THE PURPOSE BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />TO REQUESTS FOR APPROVAL FOR EQUAL PRODUCTS IN CONFORMANCE WITH SECTION 01600.
<br />1.05 JOINT TREATMENT SYSTEMS
<br />2. PROVIDE SEAM ADHESIVE SUCH AS W.W. HENRY COMPANY NO. 246, ROBERTS COMPANY NO,
<br />A. SYSTEM SHALL BE PERFORATED TAPE AND CEMENT RECOMMENDED THE GYPSUM MANUFACTURER
<br />41-0502, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED FOR THE PURPOSE
<br />PART 3 EXECUTION
<br />B. APPLY MATERIALS IN STRICT ACCORDANCE TO MANUFACTURER'S RECOMMENDATIONS. FILL JOINTS WITH
<br />BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />JOINT COMPOUND, EMBED PERFORATED TAPE AND APPLY A SKIM COAT OF JOINT COMPOUND OVER TAPE.
<br />C. AT INTERSECTION OF CARPET AND FLOOR TILE, PROVIDE ROPPE COMPANY, INC. VINYL TILE CARPET JOINER
<br />3.01 INSTALLATION
<br />APPLY TWO ADDITIONAL COATS OF JOINT COMPOUND ALLOWING AT LEAST 24 HOURS BETWEEN EACH COAT.
<br />188 OR EQUIVALENT.
<br />A. INSTALLATION OF MISCELLANEOUS ITEMS SHALL BE IN COMPLIANCE WITH MFR'S CURRENT PRINTED
<br />SAND EACH COAT. FINISH SURFACES SHALL BE UNIFORMLY SMOOTH, TRUE AND IN SATISFACTORY CONDITION
<br />D. PROVIDE OTHER MATERIALS, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A COMPLETE AND
<br />RECOMMENDATIONS AND AS MAY BE SHOWN ON DRAWINGS AND SPECIFIED HEREINAFTER.
<br />TO RECEIVE PAINT,
<br />PROPER INSTALLATION, A$ SELECTED BY THE CONTRACTOR, SUBJECT TO THE APPROVAL OF THE
<br />END OF SECTION 09250
<br />ARCHITECT.
<br />PART 4 SPECIALTIES
<br />E. ALLOW THE OWNER TO INSPECT AND SELECT FROM SCRAP CARPET REMAINING AFTER THE INSTALLATION,
<br />BUNDLE, WRAP IN BURLAP, AND DELIVER TO THE OWNER THE CARPET SCRAPS SO SELECTED.
<br />4.01 MISCELLANEOUS SPECIALTIES SCHEDULE
<br />SECTION OWOO CERAMIC TILE
<br />A. PROVIDE FOLLOWING ITEMS:
<br />I. RESIDENTIAL KITCHEN EQUIPMENT
<br />PART I GENERAL
<br />END OF SECTION 09560
<br />a. REFRIGERATOR
<br />(UKENMORE MODEL NO. 46-19842, 18 CU. FT. REFRIGERATOR/FREEZER WITH AUTOMATIC ICE MAKER -
<br />COLOR - WHITE ON WHITE,
<br />1.01 GENERAL
<br />SECTION 09900 PAINTING
<br />B. MICROWAVE
<br />A. CERAMIC AND TYPES ARE INDICATED ON THE DRAWINGS AND ARE FROM A SINGLE MANUFACTURER. OTHER
<br />I. KENMORE MODEL NO. 20-69301.
<br />MANUFACTURERS WILL NOT BE CONSIDERED.
<br />PART I GENERAL
<br />C. COUNTERTOP ICEMAKER
<br />B. DELIVER MATERIALS IN ORIGINAL CONTAINERS WITH SEALS UNBROKEN AND LABELS INTACT UNTIL TIME OF
<br />I. DCM - 210 BAN, 16 9/16" x 24 3/16" x 31 1/8" BY HOSHIZAKI AMERICA INC. (800) 345-1325
<br />USES. ENGAGE AN EXPERIENCED INSTALLER WHO HAS SUCCE56FULLY COMPLETED TILE INSTALLATIONS
<br />I.01 GENERAL
<br />SIMILAR IN MATERIAL, DESIGN, AND EXTENT TO THAT INDICATED FOR THE PROJECT.
<br />A. IT IS THE INTENT OF THIS SPECIFICATION TO PRODUCE A PREMIUM JOB, WHICH WILL PROVIDE THE MAXIMUM
<br />END OF SECTION 10950
<br />C. COMPLY WITH PARTS OF ANSI 108 SERIES OF FINE INSTALLATION STANDARDS INCLUDED UNDER "AMERICAN
<br />DURABILITY, WHICH CAN REASONABLY BE EXPECTED FROM A PAINTED SURFACE,
<br />NATIONAL STANDARD SPECIFICATIONS FOR THE INSTALLER OF CERAMIC TILE" THAT APPLY TO TYPE OF
<br />B, "PAINT" INCLUDES COATING SYSTEMS MATERIALS, PRIMERS, EMULSIONS, ENAMELS, STAINS, SEALERS, AND
<br />SETTING AND GROUT MATERIALS AND METHODS INDICATED. TILE MAY BE THIN -SET.
<br />FILLERS, AND OTHER APPLIED MATERIALS WHETHER USED AS PRIME, INTERMEDIATE, OR FINISH COAT.
<br />1.02 MORTAR AND GROUT
<br />C. SPECIFIED PRODUCTS BELOW ARE MANUFACTURED BY SHERWIN WILLIAMS, EXCEPT WHERE OTHER
<br />A. MORTAR SHALL BE PORTLAND CEMENT ASTM C150, TYPE I. GROUT SHALL BE ACID RESISTANT UPCO
<br />MANUFACTURERS ARE INDICATED, AND ESTABLISH A STANDARD OF QUALITY. EQUIVALENT PRODUCTS OF
<br />HYDROMENT, TYPE AS RECOMMENDED BY THE MANUFACTURER FOR THE SPECIFIC TYPE OF TILE AND
<br />OTHER ACCEPTABLE MANUFACTURERS MAY NOT BE USED UNLESS APPROVED BY ARCHITECT.
<br />METHOD OF INSTALLATION, COLR FOR FLOOR TILE IS SPECIFIED ON THE DRAWINGS.
<br />D. PROVIDE BEST GRADE AND QUALITY MATERIALS AND PRODUCTS MANUFACTURED BY SHERWIN WILLIAMS.
<br />B. DO NOT GROUT TILE UNTIL TILE IS FIRMLY SET, SOAK OR DAMPEN JOINTS OF THE TILE TO BE GROUTED WITH
<br />MATCH COLORS AS INDICATED ON THE DRAWINGS. USE PREMIXED PAINTS INSOFAR AS POSSIBLE. THIN ONLY
<br />PORTLAND CEMENT GROUT. SOAK OR DAMPEN OTHER JOINTS AS RECOMMENDED BY THE GROUT
<br />AS PERMITTED ANY MANUFACTURER'S LABEL INSTRUCTIONS, AND AVOID UNNECESSARY THINNING,
<br />MANUFACTURER FORCE GROAT INTO JOINT LINES COMPLETELY IDILING JOINTS WITH COMPACTED GROUT AND
<br />E. PROTECT FINISHED SURFACES, WORK OF OTHER TRADES, AND PROPERTY OF THE OWNER FROM DAMAGE AND
<br />COVERING MORTAR FINISH JOINTS OF SQUARE EDGED TILE FLUSH WITH SURFACE, STRIKE OFF TOOL JOINTS
<br />DEFACEMENT, COVER FLOORS AND FIXED EQUIPMENT WITH DROP CLOTHS.
<br />OF CUSHION EDGED TILE TO DEPTH OF CUSHION. FILL GAPS AND SKIPS, AND RETOOL.
<br />F. PREPARE SURFACES ACCORDING TO PAINT MANUFACTURER'S INSTRUCTIONS, EXAMINE FACTORY FINISHED
<br />AND PRIMED SURFACES TO BE PAINTED, AND VERIFY COMPATIBILITY OF EXISTING MATERIAL WITH PAINT TO
<br />BE APPLIED, APPLY PAINT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS
<br />1.03 CLEANING
<br />ONLY TO SURFACES WHICH ARE THOROUGHLY DRY, SMOOTH, EVEN, GLEAN, FREE OF DUST AND PROPERLY
<br />A. UPON COMPLETION OF THE PLACEMENT AND GROUTING, GLEAN TILE SURFACE SD THAT THEY ARE FREE OF
<br />PREPARED 70 RECEIVE THE INTENDED FINISH,
<br />FOREIGN MATTER. REMOVE LATEX-PORTLAND CEMENT GROUT RESIDUE FROM TILE AS SOON AS POSSIBLE
<br />UNGLAZED TILE MAY BE CLEANED WITH ACID SOLUTIONS ONLY WHEN PERMITTED BY TILE AND GROUT
<br />MANUFACTURER'S PRINTED INSTRUCTIONS, BUT SOONER THAN 14 DAYS AFTER INSTALLATION. FLUSH SURFACE
<br />1.02 PAINTING
<br />WITH CLEAN WATER BEFORE AND AFTER CLEANING.
<br />A. ACCEPTABLE MATERIALS
<br />I. ALL PAINTING TO BE SCHEDULED IN THE FINISH SCHEDULE.
<br />END OF SECTION 09300
<br />2. EQUIVALENT PRODUCTS OF THE FOLLOWING ARE ALSO ACCEPTABLE:
<br />PRATT 4 LANBERTT
<br />GLIDDEN
<br />PORTER
<br />BENJAMINE MOORE
<br />B. UNDERCOATS AND THINNERS
<br />I. PROVIDE UNDERCOAT PAINT PRODUCED BY THE SAME MANUFACTURER
<br />OF FINISH COAT,
<br />2. USE ONLY THINNERS RECOMMENDED BY THE PAINT MANUFACTURER AND USE ONLY
<br />THE RECOMMENDED LIMITS.
<br />C. COLOR SCHEDULES
<br />1. PROVIDE PAINTING AS SCHEDULED IN THE FINISH MATERIALS SCHEDULE,
<br />`, Q t
<br />DIVISION �1 �/y SIN 1
<br />VIA �.f U
<br />a. ON GYPSUM DRYWALL, USE:
<br />I. FIRST COAT - PIGMENTED PRIMER/SEALER
<br />NONE SPECIFIED
<br />2. SECOND COAT - ACRYLIC LATEX ENAMEL
<br />3. THIRD COAT - ACRYLIC LATEX ENAMEL
<br />b. ON FERROUS METAL, USE:
<br />I. FIRST COAT - RUST INHIBITIVE ALKYD METAL PRIMER
<br />Q
<br />1� Vl�t I2 FURNISHINGS
<br />DIVISION
<br />2. SECOND COAT -SEMI-GLOSS ALKYD ENAMEL
<br />3. THIRD COAT - SEMI -GLOSS ALKYD ENAMEL
<br />NONE SPECIFIED
<br />c. ON WOOD DOORS, USE:
<br />I. FIRST COAT - STAIN (SEE FINISH SCHEDULE)
<br />2. SECOND COAT - STAIN (SEE FINISH SCHEDULE)
<br />3. THIRD COAT - VARNISH LOW SHEEN "RUBBED EFFECT"
<br />I
<br />DIVISION 13 SPECIAL CONSTRUCTION
<br />SPECIAL
<br />END OF SECTION 09900
<br />NONE SPECIFIED
<br />DIVISION 14 CONVEI'INC SYSTEMS
<br />NONE SPECIFIED
<br />DIVISION 15 MECHANICAL
<br />SEE MECHANICAL
<br />DIVISION I& ELECTRICAL
<br />SEE ELECTRICAL
<br />REVISIONS
<br />BY
<br />fl
<br />u
<br /><r
<br />4 00
<br />M
<br />v m N
<br />.-a co
<br />Q�
<br />o
<br />mot` U
<br />U
<br />C (i,
<br />1
<br />/ c U
<br />1�� U N
<br />. LO
<br />t- > .
<br />�I E
<br />Q o - o
<br />00 3
<br />75 " >.� 3
<br />3ti 3
<br />.n G
<br />N
<br />�w co
<br />Wrl
<br />C0
<br />N
<br />� � O
<br />o #
<br />`a
<br />U U
<br />Z
<br />Z 0
<br />J
<br />U � �
<br />O m �L J
<br />t
<br />} Q Lt_
<br />C
<br />W :3o V0 0
<br />�
<br />=U
<br />>j W i3 O
<br />c U
<br />C `0 N d 0
<br />0 (0 (D
<br />Q J �IZ N
<br />0 Q CO
<br />FX U_
<br />0 0
<br />L" cW
<br />Date: 12. 23. 14
<br />Scale: AS NOTED
<br />Project Mgr: DSH
<br />Drawn: AZP
<br />Job: 14-137
<br />Sheet
<br />N2
<br />H:\Projects\Projects 2014\14137 - FMC Z Hills Diagnostics\04-CD\01-CDA\04-Architectura]\N-SPECS.dwg, 12/23/2014 4:03:09 PM, sharrison, Xerox 6604 PS.pc3
<br />
|