|
EXTERIOR RESEARCH & DESIGN, LLC,
<br />Certificate of Authorization #9503
<br />353 Christian Street
<br />Oxford, CT 06478
<br />5.3.3 Use of the wind load performance worksheets is limited to wall height less than or equal to 30
<br />{ 3
<br />j PHONE: (203) 262-9245
<br />feet on Category II, enclosed buildings. For buildings having conditions in excess of these
<br />FAX: (203) 262-9243
<br />parameters, a qualified design professional shall determine design pressures in accordance with
<br />FBC Chapter 16 on a project -specific basis for comparison to wind load resistance data in
<br />EVALUATION REPORT
<br />accordance with ASTM D 5206' and Annex Al of D 3679".
<br />CertainTeed Corporation Evaluation Report C10040.04.09
<br />5.4 All products in the wall assembly shall have quality assurance audit in accordance with the FBC
<br />FL12483
<br />803 Belden Road
<br />Date of Issuance: 04/28/2009
<br />and F.A.C. Rule 9B-72.
<br />Jackson, MI 49203
<br />6. INSTALLATION:
<br />SCOPE:
<br />This Evaluation Report is issued under Rule 9B-72 and the applicable rules and regulations
<br />CertainTeed vinyl siding systems shall be installed in accordance with ASTM D 4756 is' and
<br />recommendations of the Vinyl Siding Institutes", subject to the Limitations / Conditions of Use noted in
<br />governing the use of construction materials in the State of Florida. The documentation submitted
<br />for the under the Florida Building Code.
<br />section 5.
<br />has been reviewed by Robert Nieminen, P.E. use of product
<br />The product described herein has been designed to comply with the 2007 Florida Building Code
<br />7• BUILDING PERMIT REQUIREMENTS:
<br />sections noted herein.
<br />As required by the Building Official or Authority Having. Jurisdiction in order to properly- evaluate the.
<br />Vytec Vinyl Siding Systems
<br />installation of this product.
<br />DESCRIPTION: CertainTeed
<br />Each unit shall bear labeling in accordance with the requirements the Accredited Quality
<br />$. MANUFACTURING PLANTS:
<br />LABELING:
<br />Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 9B-72 QA
<br />Assurance Agency noted herein.
<br />This Evaluation Report is valid until such time as the named product(s)
<br />requirements.
<br />CONTINUED COMPLIANCE:
<br />changes, the referenced Quality Assurance documentation changes, or provisions of the Code that
<br />Q ' g, QUALITY ASSURANCEENTITY•
<br />relate to the product change. Acceptance of this Evaluation Report by the named client constitutes
<br />agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality
<br />Architectural Testing (QUA1844)
<br />Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation
<br />(717) 764-7700
<br />vsi
<br />Report relative to updated Code requirements with each Code Cycle,
<br />ev�'vr_afct�tst.cofn
<br />ADVERTISEMENT: The Evaluation Report nurriber preceded by the words "Trinity I ERD Evaluated"
<br />the Evaluation Report is displayed, then
<br />_ THE TWO -PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT -
<br />may be displayed in advertising literature. If any portion of
<br />It shall be done In its entirety.
<br />D5206-96(2002)e1, Standard Test Method for Wridfoad Resistance of Rigid Pok(Yinyl Chloride) (PYC) Siding, © ASTM.
<br />INSPECTION • Upon request, a copy of this entire Evaluation Report shall be provided to the user by
<br />M D3679-05, Standard Specification for Rigid Poly(Yinyf Chloride) (PVC) Siding, @ ASTM.
<br />the -manufacturer or its distributors and shall be available for inspection at the job site at the
<br />"D4756-06, Standard Practice for Installation of Rigid Pok(Vinyl Chloride) (PVC) Siding and Soft, © ASTM.
<br />request of the Building Official.
<br />"Complete information on the Vinyl Siding Institute can be found at vwvv.yirZklsid,�o:�g.
<br />This Evaluation Report consists of pages i through 3, plus a 2-page Appendix.
<br />Prepared by:
<br />- • M1y -
<br />..- ,.ten
<br />The facsimile seal appearing was authorized
<br />b Robert Nieminen, P.E. on 04/28/2009
<br />t Y t3f _
<br />This does not serve as an electronically signed
<br />been
<br />•�@ ' } document, signed, seated hardcopies have
<br />Robert J.M. Nieminen, P.E. gal°iO � t `'ti transmitted to the Product Approval Administrator and
<br />Florida Registration No, 59166, Florida DCA ANE1983 to the named client
<br />CERTIFICATION OF INDEPENDENCE:
<br />Exterior Research & Design; LLC. d/b/a Trinity I ERD does not have, nor does it intend to acquire or will it
<br />1,
<br />a financial interest in any company manufacturing or distributing products it evaluates.
<br />acquire,
<br />2. Exterior Research & Design, LLC. d/b/a Trinity I ERD is not owned, operated or controlled by any company
<br />manufacturing or distributing products it evaluates.
<br />Robert Nieminen, P,E. does not have nor will acquire, a financial interest in any company manufacturing or
<br />3.
<br />distributing products for which the evaluation reports are being issued.
<br />financial interest in any other entity involved in
<br />4. Robert Nieminen, P.E. does not have, nor will acquire, a
<br />• the approval process of the product.
<br />'
<br />Exterior Research and Design, LLC. Evaluation Report C10040.04.09
<br />Certificate of Authorization #9503 FL12483
<br />Date of Issuance: 04/28/2009
<br />Page 3of3
<br />:" ti n ...,
<br />PANEL WALLS - SIDING EVALUATION:
<br />1.
<br />SCOPE:
<br />Product Category: Panel Walls
<br />Sub -Category: Siding
<br />Compliance Statement: Vytec Vinyl Sidling Systems, as produced
<br />by CertainTeed Corporation, have
<br />demonstrated compliance with the following sections of the Florida
<br />Building Code through testing in
<br />accordance with the following Standards. Compliance is subject to the Installation Requirements and
<br />Limitations / Conditions of Use set forth herein.
<br />2.
<br />STANDARDS:
<br />Section Property Standard
<br />Year
<br />1404.9, 1465.13 Specification ASTM D3679
<br />2005
<br />3.
<br />REFERENCES:
<br />i
<br />Entity Examination Reference
<br />Date
<br />ATI(TST1558) ASTM D5206 01-37056.01
<br />04/14/2000
<br />ATI (TST1558) ASTM D5206 01-45281.01
<br />05/23/2003
<br />ATI (TST1558) ASTM D3679 VSI Certification
<br />Current
<br />RADCO (TST1987) ASTM D5206 RAD-2095
<br />09/01/1998
<br />RADCO (TST1987) ASTM D5206 RAD-2251
<br />05/01/1999
<br />RADCO (TST1987) ASTM D5206 RAD-2366
<br />11/01/1999
<br />RADCO (TST1987) ASTM D5206 RAD-2660
<br />11/01/2000
<br />ATI (QUA 1844) Quality Control ATI QA Program
<br />04/24/2009
<br />4.
<br />PRODUCT DESCRIPTION:
<br />This Evaluation Report covers rigid polyvinyl chloride (PVC) siding produced by CertainTeed Corporation
<br />in a variety of profiles and surface textures / colors. This evaluation is limited to the specific product
<br />trade names referenced in this report subject to the Installation
<br />Requirements and Limitations /
<br />Conditions of Use herein.
<br />Brand
<br />Product
<br />Profiles
<br />Thickness
<br />Vytec
<br />Accord 8
<br />Sin le 8
<br />0.045"
<br />Accord Premium
<br />D4.5 D4.5DL
<br />0.042"
<br />Accord Premium Pkis
<br />D4.5 D4.5DL D4.5DL
<br />0,044"
<br />Accord Standard
<br />D4 D4DL D4.5131-
<br />0.040"
<br />Board & Batten
<br />Single 6.25 `
<br />0.044"
<br />Eminence
<br />D4.5 D4.5DL
<br />0.046"
<br />Nantucket
<br />D4 D4DL D4.5DL D5
<br />0.040"
<br />Prestige
<br />D4.5 D4.5DL D5DL
<br />0.044"
<br />Proside
<br />Bevel 8
<br />0.045"
<br />Proside
<br />D4 D4.5 134.513E
<br />0.042"
<br />S. LIMITATIONS:
<br />5.1 This evaluation report is not for use in HVHZ.
<br />5.2 Vinyl Siding is limited to Type V construction
<br />5.3 Limitations relating to wind load resistance are outlined in Appendix 1.
<br />I-d f t -for yin I siding are limited to mi11/2"1'" long (min. 3/4-inch
<br />5.3.1 unless otherwise no a as ene y
<br />penetration) x 0.125" shank diameter x minimum 3/8" head diameter galvanized roofing nails.
<br />5.3.2 Unless otherwise noted nails shall engage the stud framing members.
<br />Exterior Research and Design, LLC. Evaluation Report C30040.04.09
<br />Certificate of Authorization #9503 FL12483
<br />Date of Issuance: 04/28/2009
<br />Page 2 of 3
<br />v
<br />FLORIDA WIND ZONE COMPLIANCE WORKSHEET, h < 30 it, Category 11, enclosed
<br />FBC Section 1404.9, 1405.13, ASTM D3679-05
<br />VYTEC
<br />Wind Speed (mph) 3-second gust
<br />d
<br />�
<br />N
<br />Product
<br />Profile
<br />Ma). Nall
<br />Spacing
<br />Nail Engage
<br />Design
<br />Pressure
<br />(PSI)
<br />90
<br />100
<br />110
<br />120
<br />130
<br />140
<br />ISO
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Accord 8
<br />Single 8
<br />16" o.c
<br />Studs
<br />80
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />OK
<br />OK
<br />OK-
<br />OK
<br />OK
<br />OK
<br />NO
<br />D
<br />OK
<br />OK-
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Accord
<br />Premium
<br />D4.5, D4SDL
<br />16" D.C.Studs
<br />78
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone s
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />NO
<br />D
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />Interior
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />D4.5, D4.SDL
<br />IV D.C.
<br />Studs
<br />144
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Accord
<br />Premium Plus
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK'
<br />OK
<br />NO
<br />D
<br />DSDL
<br />16" o.c
<br />Studs
<br />70
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />C
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />NO
<br />D
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Accord
<br />Standard
<br />D4, D4131
<br />D4.5DL
<br />16" D.C.
<br />Studs
<br />80
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />BEnd
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone 5
<br />kOK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />D
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />Cinterior
<br />OSB,
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />NO
<br />D
<br />Board & Batten
<br />Single 6.25
<br />16" D.C.
<br />Plywood
<br />56
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />and/or Studs
<br />End
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />NO
<br />C
<br />OK
<br />OK
<br />OK
<br />N0.4-
<br />NO
<br />NO
<br />NO
<br />D
<br />OK
<br />OK
<br />OK.
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Eminence
<br />D4.5, D4.SDL
<br />16" o.c.
<br />Studs
<br />128
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />ER C10040:04.09-i
<br />EXTERIOR RESEARCH DESIGN, LLC. CertainTeed---FL12483
<br />FLORIDA WIND ZONE COMPLIANCE WORKSHEET, h < 30 ft, Category 11, enclosed
<br />FBC Section 1404.9, 1405.13, ASTM D3679-05
<br />VYTEC
<br />Wind Speed (mph) 3-second gust
<br />L
<br />.2a
<br />0 X
<br />Q
<br />N
<br />-
<br />Product
<br />-.
<br />Profile
<br />Max Nail
<br />Spacing
<br />Nail Engage
<br />Design
<br />Pressure
<br />(P5�
<br />90
<br />100
<br />-
<br />110
<br />120
<br />130
<br />140
<br />ISO
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OiK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CKOK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />O}K
<br />OK
<br />D
<br />Nantucket
<br />D4, D4DL
<br />134.5131., D5
<br />16" o.c.
<br />Studs
<br />80
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />B
<br />End
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OAK
<br />Iv0
<br />D
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />B
<br />Interior
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />O
<br />OK
<br />COK
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />D4.5, 134.513L
<br />16" o.c.
<br />Studs
<br />144
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />D
<br />Prestige
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OLK
<br />NO
<br />D
<br />DSDL
<br />I6" o.c.
<br />Studs
<br />70
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK -
<br />OK
<br />OK
<br />Ode.
<br />iVO
<br />C
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C+O
<br />M1.`
<br />NO
<br />D
<br />OK
<br />OK
<br />OK
<br />OK_
<br />OK
<br />CK
<br />OK
<br />B
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />C
<br />Interior
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />D
<br />D4, D4.5, D4SDL
<br />Ib" o.c
<br />Studs
<br />78
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />C
<br />5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />771one
<br />NO
<br />NO
<br />D
<br />Proside
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OfG
<br />OK
<br />B '
<br />Interior
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />C
<br />Zone 4
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />D
<br />Bevel 8
<br />1 e D.C.
<br />Studs
<br />80
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />CK
<br />OK
<br />B
<br />End
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />OKOK
<br />C
<br />Zone 5
<br />OK
<br />OK
<br />OK
<br />OK
<br />OK
<br />o4K
<br />h1O
<br />D
<br />a = 10% of least horizontal dimension or 40% of height, but not
<br />less than either 4% of least horizontal dimension or 3 feet.
<br />C4)
<br />/iieS.4
<br />y �
<br />lu
<br />W
<br />z
<br />Z
<br />O
<br />in
<br />N
<br />i m
<br />o0
<br />00
<br />N
<br />n
<br />I UN
<br />0
<br />o
<br />01
<br />i }�
<br />0
<br />(N
<br />mm
<br />� =N
<br />U Ulm
<br />Jw
<br />PJLL
<br />rn L-
<br />0
<br />
|