|
GENERAL ELECTRICAL NOTES
<br />1. ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (N.E.C. 2008) AND
<br />GOVERNING MUNICIPAL, STATE AND LOCAL CODES. ALL MATERIAL SHALL BE NEW AND SHALL BEAR THE
<br />U.L. LABEL WHERE APPLICABLE.
<br />2. ALL WORK SHALL BE PERFORMED BY A LICENSED ELECTRICAL CONTRACTOR IN A FIRST CLASS
<br />WORKMANLIKE MANNER. THE COMPLETED SYSTEM SHALL BE FULLY OPERATIVE AND ACCEPTED BY THE
<br />OWNER.
<br />3. IT IS NOT THE INTENT OF THESE PLANS TO SHOW EVERY MINOR DETAIL OF CONSTRUCTION. THE
<br />CONTRACTOR IS EXPECTED TO FURNISH AND INSTALL ALL ITEMS FOR A COMPLETE ELECTRICAL SYSTEM
<br />AND PROVIDE ALL REQUIREMENTS NECESSARY FOR EQUIPMENT TO BE PLACED IN PROPER WORKING
<br />ORDER.
<br />4. CONTRACTOR SHALL MAKE ALL NECESSARY CUTTING AND DO ALL THE REPATCHING AS NECESSARY FOR
<br />THE PROPER EXECUTION OF THIS WORK.
<br />5. AFTER COMPLETION OF THE INSTALLATION, THE SYSTEM SHALL TEST FREE FROM SHORT CIRCUITS AND
<br />GROUNDS.
<br />6. WHERE ELECTRICAL CONDUCTORS ARE INSTALLED IN CONDUIT, THE CONDUIT SHALL COMPLY WITH THE
<br />N.E.C. REQUIREMENTS.
<br />7. ALL CONDUCTORS SHALL BE COPPER. NO CONDUCTOR SHALL BE SMALLER THAN #12 AWG AND SHALL
<br />BE RATED FOR 600VOLTS THWN OR THHN INSULATION. INSTALL A GROUNDING CONDUCTOR WITH ALL
<br />CIRCUITS, UNLESS NOTED OTHERWISE, SIZED PER N.E.C. 250-122.
<br />8. VERIFY BREAKER AND CORRESPONDING WIRE SIZES FOR ALL ELECTRICAL EQUIPMENT. DO NOT ORDER
<br />MATERIAL BEFORE VERIFYING BREAKER & WIRE SIZE. REPORT ANY DISCREPANCY IMMEDIATELY TO THE
<br />ENGINEER OF RECORD.
<br />9. SAFETY SWITCHES SHALL BE SQUARE 'D', GENERAL ELECTRIC, OR WESTINGHOUSE, FUSED OR
<br />NON -FUSED AND SIZED AS INDICATED. NEMA 3R WHEN EXPOSED TO WEATHER
<br />10. PANELS SHALL BE SQUARE 'D', GENERAL ELECTRIC OR EQUAL, TYPE AND NUMBER OF BREAKERS AS
<br />INDICATED ON PANEL SCHEDULE. STENCIL PANEL DESIGNATION ON INSIDE OF PANEL. ALL TWO -POLE
<br />BREAKERS SHALL BE COMMON TRIP. PROVIDE TYPE WRITTEN SCHEDULE IN EACH LOAD CENTERS.
<br />CONNECTION TO MAIN BUS SHALL BE WITH BURNDY ANNULAR COMPRESSION LUGS. PANELS AIC RATING
<br />SHALL BE AS INDICATED ON PLANS.
<br />11. PROVIDE NAMEPLATES FOR ALL PANEL BOARDS, DISCONNECTS, TRANSFORMER, TERMINAL CABINETS AND
<br />ALL ELECTRICAL EQUIPMENT IDENTIFIED BY NAME ON DRAWINGS.
<br />12, ALL ELECTRICAL MATERIALS, DEVICES, APPLIANCES AND EQUIPMENT SHALL BE LABEL LISTED BY AN
<br />APPROVED THIRD PARTY TESTING AGENCY.
<br />13. LOAD DATA IS BASED ON INFORMATION GIVEN ENGINEER AT TIME OF DESIGN. VERIFY ALL EQUIPMENT
<br />AND PANEL SIZES BEFORE ORDERING AND BEFORE INSTALLATION,
<br />14. ALL EXTERIOR ELECTRICAL EQUIPMENT SHALL BE ANCHORED TO COMPLY WITH LOCAL CODE FOR WIND
<br />RESISTANCE.
<br />15. ALL ELECTRICAL AND COMMUNICATIONS OUTLETS TO BE AT 15" A.F.F TO BOTTOM OF OUTLET UNLESS
<br />OTHERWISE NOTED, ALL LIGHT SWITCHES SHALL BE 0 48" AFF. TO TOP OF SWITCH.
<br />16. 11ME CLOCK FOR LIGHTING CONTROL TO BE AN ASTRONOMICAL TIME CLOCK.
<br />17. THE CONTRACTOR SHALL CONTACT THE LOCAL POWER COMPANY AND OBTAIN, IN WRITING, THE AVAILABLE
<br />FAULT CURRENT OF THE UTILITY TRANSFORMER. THE CONTRACTOR SHALL ENSURE THAT ALL ELECTRICAL
<br />EQUIPMENT HAS AN AMP INTERRUPTING CAPACITY (AIC) GREATER THAN THE AVAILABLE FAULT CURRENT
<br />AT ANY POINT IN THE ELECTRICAL DISTRIBUTION SYSTEM.
<br />18. WIRING MIE HOD:
<br />ALL CONDUCTORS SHALL BE INSTALLED IN ELECTRICAL METALLIC TUBING (EMT) UNLESS OTHERWISE
<br />NOTED. ALL FITTINGS AND COUPLINGS FOR EMT CONDUIT SHALL BE ALL STEEL RAIN TIGHT
<br />COMPRESSION TYPE OR ALL STEEL CONCRETE TIGHT SET SCREW TYPE.
<br />SCHEDULE 40 PVC CONDUIT, WITH FITTINGS AND COUPLINGS APPROPRIATE FOR THE USE, SHALL BE
<br />USED UNDERGROUND OR BELOW SLABS ON GRADE.
<br />19. SEAL ALL NEW CONDUIT PENETRATIONS THROUGH ARE RATED WALLS, CEILINGS, FLOORS, ETC., TO
<br />MAINTAIN EXISTING FIRE RATING CONDITIONS. FURNISH AND INSTALL FIRE RATED ENCLOSURES FOR ALL
<br />EQUIPMENTS PENETRATING FIRE RATED ENVELOPES, SPACES, ECT.
<br />20. ELECTRICAL CONTRACTOR IS RESPONSIBLE TO PROVIDE WIRING FOR HVAC SYSTEM: A/C EQUIPMENT(S),
<br />SMOKE DEFECTORS, THERMOSTATS, TEST STATIONS, MOTORIZED VOLUME DAMPERS, ETC. ELECTRICAL
<br />CONTRACTOR SHALL COORDINATE WITH MECHANICAL DRAWINGS AND PROVIDE ALL NECESSARY CONTROL
<br />WIRING. ELECTRICAL CONTRACTOR TO THOROUGHLY REVIEW MECHANICAL PLANS AND PROVIDE POWER TO
<br />ANY MECHANICAL EQUIPMENT OR DEVICE THAT IS NOT SHOWN ON ELECTRICAL PLANS BUT IS SHOWN ON
<br />MECHANICAL PLANS.
<br />21. INSTALL 'GFCI" GROUND FAULT INTERRUPTER RECEPTACLES WITH WEATHERPROOF COVER WITHIN 25 FT
<br />OF HVAC EQUIPMENT, MOUNT RECEPTACLE ON UNISTRUT (UNLESS HVAC EQUIPMENT IS SPECIFIED WITH
<br />FACTORY INSTALLED CONVENIENT RECEPTACLE) .
<br />22. WHEN NEW ELECTRIC SERVICE IS BEING INSTALLED, IT IS THE GENERAL CONTRACTOR'S RESPONSIBILITY
<br />TO COORDINATE WITH FPL/FPL ENGINEERS ON THE SIZE OF THE FPL TRANSFORMER THAT IS REQUIRED
<br />TO PROVIDE THE NEW ELECTRIC SERVICE SHOWN ON ELECTRIC PLANS, GC HAS TO INFORM THE OWNER
<br />ABOUT ANY EXTRA FPL CHARGES THAT MIGHT OCCUR IN ORDER TO PULL NEW SERVICE. THIS HAS TO
<br />BE DONE AS EARLY AS POSSIBLE DURING THE BIDDING PROCESS.
<br />23. ELECTRICAL SERVICE EQUIPMENT MUST BE 3' ABOVE MSL, AND 8' ABOVE N.V.G.D. VERIFY AT SITE. ALL
<br />ELECTRICAL EQUIPMENTS SHALL BE INSTALLED ABOVE FLOOD LEVEL.
<br />24. CONTRACTOR MUST VISIT THE SITE PRIOR TO BID OR CONSTRUCTION TO VERIFY ALL EXISTING
<br />CONDITIONS. BEFORE SUBMITTING BID, BECOME THOROUGHLY FAMILIAR WITH ACTUAL EXISTING CONDITIONS
<br />AT THE BUILDING SITE. THE INTENT OF THE WORK IS SHOWN ON THE DRAWINGS AND DESCRIBED
<br />HEREINAFTER. BY THE ACT OF SUBMITTING A BID PROPOSAL FOR WORK, THE CONTRACTOR SHALL BE
<br />DEEMED TO HAVE MADE SUCH STUDY AND EXAMINATION AND TO ACCEPT ALL CONDITIONS PRESENT AT
<br />THE SITE. NO REQUEST FOR ADDITIONAL PAYMENT SHALL BE CONSIDERED AS VALID, DUE TO THE
<br />FAILURE TO ALLOW FOR CONDITIONS WHICH MAY EXIST. CONTRACTOR TO REPLACE ANY EXISTING DEVICE
<br />OR COMPONENT THAT IS CALLED AS EXISTING IF IT IS NOT FULLY OPERATIONAL.
<br />25. WIRING METHODS IN ALL PATIENT CARE AREAS TO BE IN COMPLIANCE WITH REDUNDANT GROUNDING
<br />REQUIREMENTS OF NEC 2008 SECTION 517.13.
<br />26. ALL DIMMING MECHANISMS HAVE TO BE COMPATIBLE WITH FIXTURE DIMMING REQUIREMENTS. CONTRACTOR
<br />MUST VERIFY ALL DIMMING MECHANISM AND FIXTURE DIMMING REQUIREMENTS BEFORE ANY ORDERING,
<br />INSTALLING, OR WIRING OF ANY DIMMING MECHANISMS AND FIXTURES.
<br />27. ALL OUTDOOR RECEPTACLES TO BE GFCI & WEATHER PROOF.
<br />28. ALL OUTDOOR DISCONNECTS AND ELECTRICAL PANELS TO BE NEMA-3R. ALL OUTDOOR DISCONNECTS
<br />AND ELECTRICAL PANELS IN A SALT SPRAY AREA TO BE NEMA-0.
<br />PER FLORIDA BUILDING CODE 2010 ENERGY CONSERVATION:
<br />505.7.3 VOLTAGE DROP.
<br />505.7.3.1 FEEDERS AND CUSTOMER OWNED SERVICE CONDUCTORS.
<br />FEEDER AND CUSTOMER OWNED SERVICE CONDUCTORS SHALL BE SIZED FOR A MAXIMUM VOLTAGE
<br />DROP OF 2 PERCENT AT DESIGN LOAD.
<br />505.7.3.2 BRANCH CIRCUITS. BRANCH CIRCUIT CONDUCTORS SHALL BE SIZED FOR A MAXIMUM
<br />VOLTAGE DROP OF 3 PERCENT AT DESIGN LOAD.
<br />505.7.4 COMPLETION REQUIREMENTS.
<br />505.7.4.1 DRAWINGS. CONSTRUCTION DOCUMENTS SHALL REQUIRE THAT WITHIN 30 DAYS AFTER
<br />THE DATE OF SYSTEM ACCEPTANCE, RECORD DRAWINGS OF THE ACTUAL INSTALLATION SHALL BE
<br />PROVIDED TO THE BUILDING OWNER, INCLUDING:
<br />1. A SINGLE -LINE DIAGRAM OF THE BUILDING ELECTRICAL DISTRIBUTION SYSTEM AND
<br />2. FLOOR PLANS INDICATING LOCATION AND AREA SERVED FOR ALL DISTRIBUTION.
<br />505.7.4.2 MANUALS. CONSTRUCTION DOCUMENTS SHALL REQUIRE THAT AN OPERATING MANUAL
<br />AND MAINTENANCE MANUAL BE PROVIDED TO THE BUILDING OWNER. THE MANUALS SHALL
<br />INCLUDE, AT A MINIMUM, THE FOLLOWING:
<br />1. SUBMITTAL DATA STATING EQUIPMENT RATING AND SELECTED OPTIONS FOR EACH PIECE OF
<br />EQUIPMENT REQUIRING MAINTENANCE,
<br />2. OPERATION MANUALS AND MAINTENANCE MANUALS FOR EACH PIECE OF EQUIPMENT REQUIRING
<br />MAINTENANCE. REQUIRED ROUTINE MAINTENANCE ACTIONS SHALL BE CLEARLY IDENTIFIED.
<br />3. NAMES AND ADDRESSES OF AT LEAST ONE QUALIFIED SERVICE AGENCY.
<br />NOTE: ENFORCEMENT AGENCIES SHOULD ONLY CHECK TO BE
<br />SURE THAT THE CONSTRUCTION DOCUMENTS REQUIRE THIS INFORMATION TO BE TRANSMITTED TO
<br />THE OWNER AND SHOULD NOT EXPECT COPIES OF ANY OF THE MATERIALS.
<br />505.3 TANDEM WIRING:
<br />LUMINAIRES DESIGNED FOR USE WITH ONE OR THREE LINEAR FLUORESCENT LAMPS GREATER THAN
<br />30 W EACH SHALL BE TANDEM WIREDTWO 0 R LUMINAIRES ARE IN THE SAME SPACE
<br />WHEN R MORE R
<br />AND ON THE SAME CONTROL DEVICE.
<br />EXCEPTIONS:
<br />1. RECESSED LUMINAIRES MORE THAN 10 FEET APART MEASURED CENTER TO CENTER.
<br />2. SURFACE -MOUNTED OR PENDANT LUMINAIRES THAT ARE NOT CONTINUOUS.
<br />3. LUMINAIRES USING THREE -LAMP HIGH FREQUENCY ELECTRONIC OR THREE -LAMP
<br />ELECTROMAGNETIC BALLASTS.
<br />4. RECESSED LUMINAIRES MORE THAN 10 FEET APART MEASURED CENTER TO CENTER.
<br />5. SURFACE -MOUNTED OR PENDANT LUMINAIRES THAT ARE NOT CONTINUOUS.
<br />6. LUMINAIRES USING THREE -LAMP HIGH -FREQUENCY ELECTRONIC OR THREE -LAMP
<br />ELECTROMAGNETIC BALLASTS.
<br />NOTE:
<br />PER FLORIDA BUILDING CODE 2010 SEC, 505.2
<br />AREAS ENCLOSED BY CEILING HEIGHT PARTITIONS SHALL HAVE AT LEAST ONE
<br />SWITCH TO CONTROL LIGHTING WITHIN THE SPACE AS SHOWN. THESE SWITCHES
<br />ARE EQUIPPED WITH OCCUPANT SENSORS THAT WILL TURN THE LIGHTS OFF
<br />WITHIN 30 MINUTES OF OCCUPANT LEAVING A SPACE REGULAR SWITCHES CAN
<br />BE USED WHEN A CEILING OCCUPANT SENSOR IS USED SEE PLAN.
<br />ALL EMERGENCY AND EXIT LIGHTS TO BE CONNECTED AHEAD OF ANY SWITCH
<br />OR TIME CLOCK
<br />OCCUPANCY SENSOR SWITCHES OR CEILING MOUNT TURN POWER ON WHEN
<br />OCCUPANT IS DETECTED FOR 30 MINUTES AND TURN POWER OFF WITHIN 30
<br />MINUTES AFTER AN OCCUPANT LEAVES THE MOTION DEFECTOR VICINITY.
<br />POSITION OF THE SWITCH (ON/OFF) DOES NOT EFFECT OCCUPANCY SENSOR
<br />CONTROL.
<br />BRANCH CIRCUIT VOLTAGE DROP
<br />MAXIMUM 3% PER 2010 FBC
<br />ENERGY CONSERVATION CODE
<br />SECTION 505.7.3.2
<br />CIRCUIT LOAD
<br />IN AMPS
<br />WIRE SIZE
<br />COPPER
<br />MAXIMUM
<br />LENGTH
<br />IN FEET
<br />5 AMPS OR LESS
<br />180
<br />6 AMPS
<br />150
<br />7 AMPS
<br />#12 AWG
<br />130
<br />8 AMPS
<br />115
<br />9 AMPS
<br />#19 AWG
<br />100
<br />10 AMPS
<br />#12 AWG
<br />90
<br />11 AMPS
<br />83
<br />12 AMPS
<br />#12 AWG
<br />75
<br />13 AMPS
<br />70
<br />14 AMPS
<br />65
<br />15 AMPS
<br />60
<br />16 AMPS
<br />57
<br />17 AMPS
<br />54
<br />18 .AMPS
<br />#12 AWG
<br />51
<br />19 AMMPS
<br />#12 AWG
<br />48
<br />20 AMPS
<br />#12 AWG
<br />1 45
<br />NOTE:
<br />THE LIGHTING SPECIFICATIONS WERE SUPPLIED BY OTHERS.
<br />CONTRACTOR TO COORDINATE WITH OWNER/OWNER REP OR
<br />OWNER'S INTERIOR DESIGNER. VERIFY THAT THE
<br />SPECIFICATIONS ON THIS PLAN ARE WHAT THE OWNER
<br />ASKED FOR AND PROPERLY WIRE CONTROLS PER
<br />MANUFACTURER SPECIFICATIONS. ELECTRICAL CONTRACTOR
<br />TO CHECK MANUFACTURER SPECIFICATIONS AND
<br />INSTALLATION INSTRUCTIONS FOR LIGHTS AND CONTROLS
<br />FOR LIGHTS PRIOR TO ORDERING AND ROUGH -IN.
<br />NOTE:
<br />FOR FLUORESCENT LUMINAIRES, PROVIDE
<br />DISCONNECTS AS PER NEC 410.130(G).
<br />..... ... ... L
<br />;
<br />1. � _.....
<br />i
<br />J-BOX#1
<br />Fin n rnnRnimATF
<br />i v I
<br />1'
<br />I ITi'�
<br />1/ Ehl
<br />y
<br />II
<br />•
<br />. l
<br />L
<br />_,,
<br />_
<br />I
<br />r
<br />:BOX
<br />#z
<br />FI
<br />LD
<br />I
<br />.....
<br />_ DIN
<br />TE
<br />I
<br />EXACTI L CA
<br />ON_
<br />I
<br />RUN 2# 12 CU + 1# 12
<br />CU GROUND MC CABLE
<br />BETWEEN ALL JBOXES OF
<br />FUTURE LIGHTS THEN
<br />CONNECT TO NEAREST JBOX
<br />AS LABELED
<br />E
<br />D,1
<br />1
<br />- - - - -- D
<br />\ FUTURE
<br />�J f SCONCE
<br />J (TYP.)
<br />r IJ 2 # 12 CU + 1 # 12 RUN 2# 12 CU + 1# 12
<br />CU GROUND TO J-BOX #1 CU GROUND MC CABLE
<br />JBOX FOR BETWEEN ALL SCONCE
<br />`C FUTURE JBOXES THEN CONNECT TO
<br />\ HI -HAT ( ) i NEAREST JBOX AS LABELED
<br />t I
<br />I
<br />I I
<br />t FOR FU E SIGN
<br />FIELD COORDINATE
<br />EXACT LOCATION
<br />I
<br />� I
<br />-rl.. ', d . i f�,E x F ,.,
<br />J iA
<br />I
<br />� I
<br />i ....
<br />6 � ' E= TE- `8' 8 ESN E �` ;iIL
<br />I
<br />1 2" EMT I
<br />CONDUIT J
<br />I ti_.
<br />L _
<br />I ,cc,E
<br />2 12 CU + I ---
<br />#
<br />J 1 # 12 CU '
<br />I
<br />GROUND TO
<br />J-BOX #2 I
<br />E 1 0 FE " J 1 _ TN T I TO _ NED, S- _-,
<br />I } i'ND E J D L a,
<br />I IT r 1 T N L, T i< T 'a
<br />I Li_';N _K B�Ll ! 7HE O PY
<br />J J
<br />DN
<br />!' - _
<br />2#12CU+1- 1. r LL Lf r.
<br />-F # 12 CU GROUND
<br />1 RUN 2# 12 CU + 1# 12
<br />TO J-BOX #3 CU GROUND MC CABLE
<br />BETWEEN ALL SCONCE
<br />XJ ,.B JBOXES THEN CONNECT TO
<br />l - NEAREST JBOX AS LABELED
<br />f .
<br />tDINNT I \ �l ni TES �,�I�I �LFa: <_, �E
<br />FUTURE LIGHTING S
<br />A
<br />HELL PLAN
<br />SCALE: 1 /8" = 1'-0"
<br />SCOPE OF WORK:
<br />PROVIDE J-BOXES AS SHOWN ON PLANS FOR FRONT CANOPY LIGHTS SIGNS AND CAMERAS.
<br />PROVIDE WIRING BETWEEN J-BOXES FOR SCONCE AND HI HATS LIGHTS AS SHOWN ON PLANS.
<br />PROVIDE 1 /2" EMT CONDUIT CONNECTING LIGHTS AND SIGN J-BOXES AS SHOWN ON PLANS.
<br />PROVIDE 3/4" CONDUIT FOR DOME CAMERAS JBOXES.
<br />ROSS PLANS WILL PROVIDE MAIN RUNS OF POWER AND CAMERA CABLES TO THESE JBOXES.
<br />ONLY FUTURE SCONCES AND HI HATS WILL HAVE MC WIRING TO JBOXES 1 , 2 AND 3, ROSS
<br />PLANS WILL PROVIDE POWER FROM PANELS TO JBOXES 1 , 2 AND 3 AND CONNECT THE MC
<br />CABLE WIRING PROVIDED ON THESE PLANS.
<br />ROSS WILL PROVIDE THE LIGHTS ON THEIR PERMIT, NO LIGHTS WILL BE INSTALLED ON THIS
<br />PERMIT ONLY JBOXES WILL BE INSTALLED.
<br />FUTURE LIGHTING LEGEND
<br />EXTERIOR DOCK LIGHTING - 'LUMARK' WPS15-MV-PE-PC
<br />150W HPS LAMPS ON PHOTO CELL, SHIELDED
<br />EXTERIOR ROSS OPERATIONS LIGHTING - 'LUMARK' WPS15-MV-L-PE
<br />150W HPS LAMPS ON PHOTO CELL, NON -SHIELDED
<br />FEATURE ARCHITECTURAL LIGHTING, (OR CENTER STANDARD IF APPROVED BY ROSS
<br />STORES). IF NOT OTHERWISE SPECIFIED, NOVA MODEL #071938-B, QUARTER SPHERE
<br />SCONCE WITH 10OW MH LAMP AND FACTORY FINISHED SHELL TO MATCH FASCIA COLOR
<br />(U.ON.). THIS EXAMPLE IS TO ESTABLISH INTENDED LEVEL OF QUALITY & TYPE OF LIGHT
<br />TO BE USED, CONTACT AWL FOR SITE SPECIFIC LIGHT FIXTURE, CONTRACTOR MUST
<br />SPECIFY SCONCE FINISH COLOR WHEN PLACING ORDER. NO EXCEPTION.
<br />O UNDER CANOPY DOWN LIGHTING, (OR CENTER STANDARD MAY BE UTILIZED IF APPROVED
<br />BY ROSS STORES). IF NOT OTHERWISE SPECIFIED, PORTFOLIO MODEL #M78-100-80LI,
<br />100 WATT, METAL HALIDE DOWNLIGHT, DAMP LABEL FIXTURE. THIS EXAMPLE IS TO
<br />ESTABLISH INTENDED LEVEL OF QUALITY & TYPE OF LIGHT TO BE USED, CONTACT AWL
<br />FOR SITE SPECIFIC LIGHT FIXTURE.
<br />W
<br />PAGING/MUSIC SYSTEM SPEAKERS PROVIDED AND INSTALLED BY ROSS AFTER TURNOVER.
<br />IN THE EVENT THAT LOCAL CODE REQUIRES LOW VOLTAGE WIRING TO BE INSTALLED IN
<br />CONDUIT, THEN 3/4" CONDUIT WITH PULL STRINGS IN PLACE LINKING SPEAKER
<br />LOCATIONS TO PAGING/MUSIC DATA BOX IN MANAGER'S OFFICE IS TO BE PROVIDED AND
<br />PLACED BY G.C. PRIOR TO CONSTRUCTION TURNOVER. CONFIRM SPEAKER LOCATIONS
<br />THROUGH ROSS CONSTRUCTION REPRESENTATIVE. 18 TO 20 LOCATIONS, TYP. CEILING
<br />MOUNTED UNLESS MARKED "W" FOR WALL MOUNTED
<br />■ PRE -FINISHED POWER POLE PROVIDED AS PART OF FRONT END MODULAR SYSTEM
<br />PROVIDED AND INSTALLED BY ROSS FIXTURE VENDOR.
<br />GYPSUM BOARD CEILING
<br />SUSPENDED ACOUSTICAL CEILING TILE
<br />BUCHANAN P.E. CONSULTING INC
<br />ELECTRICAL * MECHANICAL * PLUMBING
<br />ENGINEERING
<br />6191 W. ATLANTIC BLVD., SUITE #2
<br />MARGATE, FL 33063
<br />Ph: 954-590-3300 Fax: 954-590-2232
<br />Email: mepengineers@aol.com
<br />RAJA BUCHANAN FL RE # 48916
<br />CERTIFICATE OF AUTHORIZATION # 8842
<br />Fro j. Mgr.
<br />JU
<br />,Job. Gapt.
<br />SG
<br />Drawn by
<br />JT
<br />RON
<br />BARR,
<br />A.I.A.
<br />Revd by
<br />STATE
<br />OF FLORIDA
<br />R1
<br />AR 0016160
<br />U
<br />U F'-
<br />}
<br />(n
<br />U
<br />H
<br />W
<br />F-2
<br />F
<br />x
<br />O W
<br />fZ
<br />Q
<br />W
<br />Fx- W
<br />O
<br />W
<br />m
<br />U
<br />d '
<br />O m
<br />U
<br />0
<br />O 5~
<br />0 0
<br />to
<br />6
<br />W
<br />O
<br />~O
<br />tn
<br />X
<br />Z
<br />a 0
<br />Si
<br />U O
<br />z¢
<br />O=
<br />F
<br />w o
<br />Q<
<br />O
<br />Z W
<br />m
<br />X 0
<br />6
<br />Z Z
<br />Q
<br />OW
<br />IY
<br />U)
<br />m
<br />z
<br />O.
<br />U)
<br />W U
<br />Z
<br />Q H
<br />Z
<br />U
<br />a
<br />z
<br />zp
<br />zW
<br /><
<br />aF_
<br />O
<br />=0
<br />n �
<br />0
<br />x
<br />ZZ°
<br />W Y
<br />W
<br />a
<br />W 1
<br />w
<br />z
<br />x
<br />a z
<br />�
<br />F-
<br />W U
<br />2
<br />F U
<br />m
<br />W
<br />O
<br />W
<br />F O
<br />W
<br />O'<
<br />T
<br />tr O
<br />O O
<br />w
<br />a of
<br />0
<br />F
<br />O O j
<br />o 0
<br />J)
<br />0
<br />O
<br />0
<br />W W
<br />°Z
<br />a 0 2
<br />z
<br />w
<br />S2
<br />0 w U
<br />T°
<br />F
<br />W
<br />W UQU
<br />F-
<br />Z O
<br />X
<br />z o-a
<br />T
<br />O o
<br />O
<br />0 W W
<br />o?<
<br />O
<br />COPYRIGHT
<br />2012
<br />BARR ARCHITECTURAL STUDIO
<br />Rev(slons:
<br />CADFILE No.
<br />1
<br />? i t
<br />I,
<br />f
<br />�"
<br />'
<br />r I
<br />E
<br />sl
<br />I
<br />i
<br />I
<br />i
<br />€
<br />r �4_
<br />c_
<br />0)
<br />L
<br />� O
<br />ch (4
<br />0c
<br />cM
<br />N a)
<br />� o N E
<br />U NCc
<br />W > Lo
<br />� Lo a
<br />o E
<br />� c13
<br />00 Cn E
<br />L LL O
<br />�00 W i
<br />(D W
<br />c r O
<br />U) U
<br />5
<br />CA 4-
<br />U
<br />L a U
<br />L
<br />Sheet Title
<br />LIGHTING
<br />PLAN
<br />Sca Is:
<br />Date: Sheet No.
<br />SEAL
<br />RA BUCH NAN
<br />F .E 48
<br />Project No. E3-0
<br />MAY 0 5 001 12-027 3 OF 3
<br />DATE:
<br />I R. I I I.. '. III I II. III. b; I:l 1 I�u:� ull, IEl A I,It�iWf �� II �T'� .III : I��
<br />
|