|
GENERAL ELECTRICAL NOTES
<br />1. ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (N.E.C. 2008) AND
<br />GOVERNING MUNICIPAL, STATE AND LOCAL CODES. ALL MATERIAL SHALL BE NEW AND SHALL BEAR THE
<br />U.L LABEL WHERE APPLICABLE.
<br />2. ALL WORK SHALL BE PERFORMED BY A LICENSED ELECTRICAL CONTRACTOR IN A FIRST CLASS
<br />WORKMANLIKE MANNER. THE COMPLETED SYSTEM SHALL BE FULLY OPERATIVE AND ACCEPTED BY THE
<br />OWNER.
<br />3. IT IS NOT THE INTENT OF THESE PLANS TO SHOW EVERY MINOR DETAIL OF CONSTRUCTION. THE
<br />CONTRACTOR IS EXPECTED TO FURNISH AND INSTALL ALL ITEMS FOR A COMPLETE ELECTRICAL SYSTEM
<br />AND PROVIDE ALL REQUIREMENTS NECESSARY FOR EQUIPMENT TO BE PLACED IN PROPER WORKING
<br />ORDER.
<br />4. CONTRACTOR SHALL MAKE ALL NECESSARY CUTTING AND DO ALL THE REPATCHING AS NECESSARY FOR
<br />THE PROPER EXECUTION OF THIS WORK.
<br />5. AFTER COMPLETION OF THE INSTALLATION, THE SYSTEM SHALL TEST FREE FROM SHORT CIRCUITS AND
<br />GROUNDS.
<br />6. WHERE ELECTRICAL CONDUCTORS ARE INSTALLED IN CONDUIT, THE CONDUIT SHALL COMPLY WITH THE
<br />N.E.C. REQUIREMENTS.
<br />7. ALL CONDUCTORS SHALL BE COPPER. NO CONDUCTOR SHALL BE SMALLER THAN #12 AWG AND SHALL
<br />BE RATED FOR 600VOLTS THWN OR THHN INSULATION. INSTALL A GROUNDING CONDUCTOR WITH ALL
<br />CIRCUITS, UNLESS NOTED OTHERWISE, SIZED PER N.E.C. 250-122.
<br />8. VERIFY BREAKER AND CORRESPONDING WIRE SIZES FOR ALL ELECTRICAL EQUIPMENT. DO NOT ORDER
<br />MATERIAL BEFORE VERIFYING BREAKER & WIRE SIZE. REPORT ANY DISCREPANCY IMMEDIATELY TO THE
<br />ENGINEER OF RECORD.
<br />9. SAFETY SWITCHES SHALL BE SQUARE 'D', GENERAL ELECTRIC, OR WESTINGHOUSE, FUSED OR
<br />NON -FUSED AND SIZED AS INDICATED. NEMA 3R WHEN EXPOSED TO WEATHER
<br />10. PANELS SHALL BE SQUARE 'D', GENERAL ELECTRIC OR EQUAL, TYPE AND NUMBER OF BREAKERS AS
<br />INDICATED ON PANEL SCHEDULE. STENCIL PANEL DESIGNATION ON INSIDE OF PANEL ALL TWO -POLE
<br />BREAKERS SHALL BE COMMON TRIP. PROVIDE TYPE WRITTEN SCHEDULE IN EACH LOAD CENTERS.
<br />CONNECTION TO MAIN BUS SHALL BE WITH BURNDY ANNULAR COMPRESSION LUGS, PANELS AIC RATING
<br />SHALL BE AS INDICATED ON PLANS.
<br />11. PROVIDE NAMEPLATES FOR ALL PANEL BOARDS, DISCONNECTS, TRANSFORMER, TERMINAL CABINETS AND
<br />ALL ELECTRICAL EQUIPMENT IDENTIFIED BY NAME ON DRAWINGS.
<br />12. ALL ELECTRICAL MATERIALS, DEVICES, APPLIANCES AND EQUIPMENT SHALL BE LABEL LISTED BY AN
<br />APPROVED THIRD PARTY TESTING AGENCY.
<br />13. LOAD DATA IS BASED ON INFORMATION GIVEN ENGINEER AT 11ME OF DESIGN. VERIFY ALL EQUIPMENT
<br />AND PANEL SIZES BEFORE ORDERING AND BEFORE INSTALLATION,
<br />14. ALL EXTERIOR ELECTRICAL EQUIPMENT SHALL BE ANCHORED TO COMPLY WITH LOCAL CODE FOR WIND
<br />RESISTANCE.
<br />15. ALL ELECTRICAL AND COMMUNICATIONS OUTLETS TO BE AT 15" A.F.F TO BOTTOM OF OUTLET UNLESS
<br />OTHERWISE NOTED, ALL LIGHT SWITCHES SHALL BE 0 48" AFF. TO TOP OF SWITCH.
<br />16. TIME CLOCK FOR LIGHTING CONTROL TO BE AN ASTRONOMICAL TIME CLOCK.
<br />17. THE CONTRACTOR SHALL CONTACT THE LOCAL POWER COMPANY AND OBTAIN, IN WRITING, THE AVAILABLE
<br />FAULT CURRENT OF THE UTILITY TRANSFORMER. THE CONTRACTOR SHALL ENSURE THAT ALL ELECTRICAL
<br />EQUIPMENT HAS AN AMP INTERRUPTING CAPACITY (AIC) GREATER THAN THE AVAILABLE FAULT CURRENT
<br />AT ANY POINT IN THE ELECTRICAL DISTRIBUTION SYSTEM.
<br />18. WIRING METHOD:
<br />ALL CONDUCTORS SHALL BE INSTALLED IN ELECTRICAL METALLIC TUBING (EMT) UNLESS OTHERWISE
<br />NOTED. ALL FITTINGS AND COUPLINGS FOR EMT CONDUIT SHALL BE ALL STEEL RAIN TIGHT
<br />COMPRESSION TYPE OR ALL STEEL CONCRETE TIGHT SET SCREW TYPE.
<br />SCHEDULE 40 PVC CONDUIT, WITH FITTINGS AND COUPLINGS APPROPRIATE FOR THE USE, SHALL BE
<br />USED UNDERGROUND OR BELOW SLABS ON GRADE.
<br />19. SEAL ALL NEW CQNDUIf PENETRATIONS THROUGH FIRE RATED WALLS, CEILINGS, FLOORS, ETC., TO
<br />MAINTAIN EXISTING FIRE RATING CONDITIONS. FURNISH AND INSTALL FIRE RATED ENCLOSURES FOR ALL
<br />EQUIPMENTS PENETRATING FIRE RATED ENVELOPES, SPACES, ECT.
<br />I
<br />I
<br />20. ELECTRICAL CONTRACTOR IS RESPONSIBLE TO PROVIDE WIRING FOR HVAC SYSTEM: A/C EQUIPMENT(S),
<br />SMOKE DETECTORS, THERMOSTATS, TEST STATIONS, MOTORIZED VOLUME DAMPERS, ETC. ELECTRICAL
<br />CONTRACTOR SHALL COORDINATE WITH MECHANICAL DRAWINGS AND PROVIDE ALL NECESSARY CONTROL
<br />WIRING. ELECTRICAL CONTRACTOR TO THOROUGHLY REVIEW MECHANICAL PLANS AND PROVIDE POWER TO
<br />ANY MECHANICAL EQUIPMENT OR DEVICE THAT IS NOT SHOWN ON ELECTRICAL PLANS BUT IS SHOWN ON
<br />MECHANICAL PLANS.
<br />21. INSTALL "GFCI" GROUND FAULT INTERRUPTER RECEPTACLES WITH WEATHERPROOF COVER WITHIN 25 FT
<br />OF HVAC EQUIPMENT, MOUNT RECEPTACLE ON UNISTRUT (UNLESS HVAC EQUIPMENT IS SPECIFIED WITH
<br />FACTORY INSTALLED CONVENIENT RECEPTACLE) .
<br />22. WHEN NEW ELECTRIC SERVICE IS BEING INSTALLED, IT IS THE GENERAL CONTRACTOR'S RESPONSIBILITY
<br />TO COORDINATE WITH FPL/FPL ENGINEERS ON THE SIZE OF THE FPL TRANSFORMER THAT IS REQUIRED
<br />TO PROVIDE THE NEW ELECTRIC SERVICE SHOWN ON ELECTRIC PLANS, GC HAS TO INFORM THE OWNER
<br />ABOUT ANY EXTRA FPL CHARGES THAT MIGHT OCCUR IN ORDER TO PULL NEW SERVICE. THIS HAS TO
<br />BE DONE AS EARLY AS POSSIBLE DURING THE BIDDING PROCESS.
<br />23. ELECTRICAL SERVICE EQUIPMENT MUST BE 3' ABOVE MSL, AND 8' ABOVE N.V.G.D. VERIFY AT SITE. ALL
<br />ELECTRICAL EQUIPMENTS SHALL BE INSTALLED ABOVE FLOOD LEVEL.
<br />24, CONTRACTOR MUST VISIT THE SITE PRIOR TO BID OR CONSTRUCTION TO VERIFY ALL EXISTING
<br />CONDITIONS. BEFORE SUBMITTING BID, BECOME THOROUGHLY FAMILIAR WITH ACTUAL EXISTING CONDITIONS
<br />AT THE BUILDING SITE. THE INTENT OF THE WORK IS SHOWN ON THE DRAWINGS AND DESCRIBED
<br />HEREINAFTER. BY THE ACT OF SUBMITTING A BID PROPOSAL FOR WORK, THE CONTRACTOR SHALL BE
<br />DEEMED TO HAVE MADE SUCH STUDY AND EXAMINATION AND TO ACCEPT ALL CONDITIONS PRESENT AT
<br />THE SITE. NO REQUEST FOR ADDITIONAL PAYMENT SHALL BE CONSIDERED AS VALID, DUE TO THE
<br />FAILURE TO ALLOW FOR CONDITIONS WHICH MAY EXIST. CONTRACTOR TO REPLACE ANY EXISTING DEVICE
<br />OR COMPONENT THAT IS CALLED AS EXISTING IF IT IS NOT FULLY OPERATIONAL
<br />25. WIRING METHODS IN ALL PATIENT CARE AREAS TO BE IN COMPLIANCE WITH REDUNDANT GROUNDING
<br />REQUIREMENTS OF NEC 2008 SECTION 517.13,
<br />26. ALL DIMMING MECHANISMS HAVE TO BE COMPATIBLE WITH FIXTURE DIMMING REQUIREMENTS. CONTRACTOR
<br />MUST VERIFY ALL DIMMING MECHANISM AND FIXTURE DIMMING REQUIREMENTS BEFORE ANY ORDERING,
<br />INSTALLING, OR WIRING OF ANY DIMMING MECHANISMS AND FIXTURES.
<br />27. ALL OUTDOOR RECEPTACLES TO BE GFCI & WEATHER PROOF.
<br />28. ALL OUTDOOR DISCONNECTS AND ELECTRICAL PANELS TO BE NEMA-3R. ALL OUTDOOR DISCONNECTS
<br />AND ELECTRICAL PANELS IN A SALT SPRAY AREA TO BE NEMA-0.
<br />PER FLORIDA BUILDING CODE 2010 ENERGY CONSERVATION:
<br />505.7.3 VOLTAGE DROP.
<br />505.7.3.1 FEEDERS AND CUSTOMER OWNED SERVICE CONDUCTORS.
<br />FEEDER AND CUSTOMER OWNED SERVICE CONDUCTORS SHALL BE SIZED FOR A MAXIMUM VOLTAGE
<br />DROP OF 2 PERCENT AT DESIGN LOAD.
<br />505.7.3.2 BRANCH CIRCUITS. BRANCH CIRCUIT CONDUCTORS SHALL BE SIZED FOR A MAXIMUM
<br />VOLTAGE DROP OF 3 PERCENT AT DESIGN LOAD.
<br />505.7.4 COMPLETION REQUIREMENTS.
<br />505.7.4.1 DRAWINGS. CONSTRUCTION DOCUMENTS SHALL REQUIRE THAT WITHIN 30 DAYS AFTER
<br />THE DATE OF SYSTEM ACCEPTANCE, RECORD DRAWINGS OF THE ACTUAL INSTALLATION SHALL BE
<br />PROVIDED TO THE BUILDING OWNER, INCLUDING:
<br />1. A SINGLE -LINE DIAGRAM OF THE BUILDING ELECTRICAL DISTRIBUTION SYSTEM AND
<br />2. FLOOR PLANS INDICATING LOCATION AND AREA SERVED FOR ALL DISTRIBUTION.
<br />505.7.4.2 MANUALS. CONSTRUCTION DOCUMENTS SHALL REQUIRE THAT AN OPERATING MANUAL
<br />AND MAINTENANCE MANUAL BE PROVIDED TO THE BUILDING OWNER. THE MANUALS SHALL
<br />INCLUDE, AT A MINIMUM, THE FOLLOWING:
<br />1. SUBMITTAL DATA STATING EQUIPMENT RATING AND SELECTED OPTIONS FOR EACH PIECE OF
<br />EQUIPMENT REQUIRING MAINTENANCE.
<br />2. OPERATION MANUALS AND MAINTENANCE MANUALS FOR EACH PIECE OF EQUIPMENT REQUIRING
<br />MAINTENANCE. REQUIRED ROUTINE MAINTENANCE ACTIONS SHALL BE CLEARLY IDENTIFIED.
<br />3. NAMES AND ADDRESSES OF AT LEAST ONE QUALIFIED SERVICE AGENCY.
<br />NOTE: ENFORCEMENT AGENCIES SHOULD ONLY CHECK TO BE
<br />SURE THAT THE CONSTRUCTION DOCUMENTS REQUIRE THIS INFORMATION TO BE TRANSMITTED TO
<br />THE OWNER AND SHOULD NOT EXPECT COPIES OF ANY OF THE MATERIALS,
<br />505.3 TANDEM WIRING:
<br />LUMINAIRES DESIGNED FOR USE WITH ONE OR THREE LINEAR FLUORESCENT LAMPS GREATER THAN
<br />30 W EACH SHALL BE TANDEM WIRED WHEN TWO OR MORE LUMINAIRES ARE IN THE SAME SPACE
<br />AND ON THE SAME CONTROL DEVICE.
<br />EXCEPTIONS:
<br />1. RECESSED LUMINAIRES MORE THAN 10 FEET APART MEASURED CENTER TO CENTER.
<br />2. SURFACE -MOUNTED OR PENDANT LUMINAIRES THAT ARE NOT CONTINUOUS.
<br />3. LUMINAIRES USING THREE -LAMP HIGH -FREQUENCY ELECTRONIC OR THREE -LAMP
<br />ELECTROMAGNETIC BALLASTS.
<br />4. RECESSED LUMINAIRES MORE THAN 10 FEET APART MEASURED CENTER TO CENTER.
<br />5. SURFACE -MOUNTED OR PENDANT LUMINAIRES THAT ARE NOT CONTINUOUS.
<br />6. LUMINAIRES USING THREE -LAMP HIGH -FREQUENCY ELECTRONIC OR THREE -LAMP
<br />ELECTROMAGNETIC BALLASTS.
<br />NOTE:
<br />PER FLORIDA BUILDING CODE 2010 SEC. 505.2
<br />AREAS ENCLOSED BY CEILING HEIGHT PARTITIONS SHALL HAVE AT LEAST ONE
<br />SWITCH TO CONTROL LIGHTING WITHIN THE SPACE AS SHOWN. THESE SWITCHES
<br />ARE EQUIPPED WITH OCCUPANT SENSORS THAT WILL TURN THE LIGHTS OFF
<br />WITHIN 30 MINUTES OF OCCUPANT LEAVING A SPACE REGULAR SWITCHES CAN
<br />BE USED WHEN A CEILING OCCUPANT SENSOR IS USED SEE PLAN.
<br />ALL EMERGENCY AND EXIT LIGHTS TO BE CONNECTED AHEAD OF ANY SWITCH
<br />OR TIME CLOCK
<br />OCCUPANCY SENSOR SWITCHES OR CEILING MOUNT TURN POWER ON WHEN
<br />OCCUPANT IS DETECTED FOR 30 MINUTES AND TURN POWER OFF WITHIN 30
<br />MINUTES AFTER AN OCCUPANT LEAVES THE M01ION DETECTOR VICINITY.
<br />POSITION OF THE SWITCH (ON/OFF) DOES NOT EFFECT OCCUPANCY SENSOR
<br />CONTROL.
<br />BRANCH CIRCUIT VOLTAGE DROP
<br />MAXIMUM 3% PER 2010 FBC
<br />ENERGY CONSERVATION CODE
<br />SECTION 505.7.3.2
<br />CIRCUIT LOAD
<br />IN AMPS
<br />WIRE SIZE
<br />COPPER
<br />MAXIMUM
<br />LENGTH
<br />IN FEET
<br />5 AMPS OR LESS
<br />180
<br />6 AMPS
<br />150
<br />7 AMPS
<br />130
<br />8 AMPS
<br />115
<br />9 AMPS
<br />100
<br />10 AMPS
<br />90
<br />11 AMPS
<br />j12 AWG
<br />83
<br />12 AMPS
<br />#12 AWG
<br />75
<br />13 AMPS
<br />70
<br />14 AMPS
<br />65
<br />15 AMPS
<br />#12 AWG
<br />60
<br />16 AMPS
<br />57
<br />17 AMPS
<br />#12 G
<br />54
<br />18 AMPS
<br />#12 AWG
<br />51
<br />19 AMPS
<br />j12 AWG
<br />48
<br />20 AMPS
<br />#12 AWG
<br />45
<br />NOTE:
<br />THE LIGHTING SPECIFICATIONS WERE SUPPLIED BY OTHERS.
<br />CONTRACTOR TO COORDINATE WITH OWNER/OWNER REP OR
<br />OWNER'S INTERIOR DESIGNER. VERIFY THAT THE
<br />SPECIFICATIONS ON THIS PLAN ARE WHAT THE OWNER i
<br />ASKED FOR AND PROPERLY WIRE CONTROLS PER
<br />MANUFACTURER SPECIFICATIONS. ELECTRICAL CONTRACTOR
<br />TO CHECK MANUFACTURER SPECIFICATIONS AND
<br />INSTALLATION INSTRUCTIONS FOR LIGHTS AND CONTROLS
<br />FOR LIGHTS PRIOR TO ORDERING AND ROUGH -IN.
<br />NOTE:
<br />FOR FLUORESCENT LUMINAIRES, PROVIDE
<br />DISCONNECTS AS PER NEC 410.130(G).
<br />ACE T TENANT
<br />RUN 2# 12 CU + 1# 12
<br />CU GROUND MC CABLE
<br />BETWEEN ALL JBOXES OF
<br />FUTURE LIGHTS THEN
<br />CONNECT TO NEAREST JBOX
<br />AS LABELED
<br />� J-BOX 1 -
<br />I�
<br />i=1i=1 n rnnRnitieTl= � I
<br />i
<br />FUTURE LIGHTING S
<br />- E
<br />D.1
<br />\_ J
<br />N
<br />HELL PLAN
<br />SCALE: 1 /8" = 1'-0"
<br />SCOPE OF WORD:
<br />PROVIDE J-BOXES AS SHOWN ON PLANS FOR FRONT CANOPY LIGHTS SIGNS AND CAMERAS.
<br />PROVIDE WIRING BETWEEN J-BOXES FOR SCONCE AND HI HATS LIGHTS AS SHOWN ON PLANS.
<br />PROVIDE 1 /2" EMT CONDUIT CONNECTING LIGHTS AND SIGN J-BOXES AS SHOWN ON PLANS.
<br />PROVIDE 3/4" CONDUIT FOR DOME CAMERAS JBOXES.
<br />ROSS PLANS WILL PROVIDE MAIN RUNS OF POWER AND CAMERA CABLES TO THESE JBOXES.
<br />ONLY FUTURE SCONCES AND HI HATS WILL HAVE MC WIRING TO JBOXES 1 , 2 AND 3, ROSS
<br />PLANS WILL PROVIDE POWER FROM PANELS TO JBOXES 1 , 2 AND 3 AND CONNECT THE MC
<br />CABLE WIRING PROVIDED ON THESE PLANS.
<br />I
<br />ROSS WILL PROVIDE THE LIGHTS ON THEIR PERMIT, NO LIGHTS WILL BE INSTALLED ON THIS
<br />PERMIT ONLY JBOXES WILL BE INSTALLED.
<br />FUTURE LIGHTING LEGEND
<br />EXTERIOR DOCK LIGHTING - 'LUMARK' WPS15-MV-PE-PC
<br />150W HPS LAMPS ON PHOTO CELL, SHIELDED
<br />a EXTERIOR ROSS OPERATIONS LIGHTING - 'LUMARK' WPS15-MV-L-PE
<br />150W HIPS LAMPS ON PHOTO CELL, NON -SHIELDED
<br />FEATURE ARCHITECTURAL LIGHTING, OR CENTER STANDARD IF APPROVED BY ROSS
<br />STORES). IF NOT OTHERWISE SPECIFIED, NOVA MODEL #071938 B, QUARTER SPHERE
<br />SCONCE WITH 10OW MH TAMP AND FACTORY FINISHED SHELL TO MATCH FASCIA COLOR
<br />(U.ON.). THIS EXAMPLE IS TO ESTABLISH INTENDED LEVEL OF QUALITY & TYPE OF LIGHT
<br />TO BE USED, CONTACT AWL FOR SITE SPECIFIC LIGHT FIXTURE. CONTRACTOR MUST
<br />SPECIFY SCONCE FINISH COLOR WHEN PLACING ORDER. NO EXCEPTION.
<br />UNDER CANOPY DOWN LIGHTING, (OR CENTER STANDARD MAY BE UTILIZED IF APPROVED
<br />BY ROSS STORES). IF NOT OTHERWISE SPECIFIED, PORTFOLIO MODEL #M78-100-80LI,
<br />100 WATT, METAL HALIDE DOWNLIGHT, DAMP LABEL FIXTURE. THIS EXAMPLE IS TO
<br />ESTABLISH INTENDED LEVEL OF QUALITY & TYPE OF LIGHT TO BE USED, CONTACT AWL
<br />FOR SITE SPECIFIC LIGHT FIXTURE.
<br />W
<br />W PAGING/MUSIC SYSTEM SPEAKERS PROVIDED AND INSTALLED BY ROSS AFTER TURNOVER.
<br />IN THE EVENT THAT LOCAL CODE REQUIRES LOW VOLTAGE WIRING TO BE INSTALLED IN
<br />CONDUIT, THEN 3/4" CONDUIT WITH PULL STRINGS IN PLACE LINKING SPEAKER
<br />LOCATIONS TO PAGING/MUSIC DATA BOX IN MANAGER'S OFFICE IS TO BE PROVIDED AND
<br />PLACED BY G.C. PRIOR TO CONSTRUCTION TURNOVER. CONFIRM SPEAKER LOCATIONS
<br />THROUGH ROSS CONSTRUCTION REPRESENTATIVE. 18 TO 20 LOCATIONS, TYP. CEILING
<br />MOUNTED UNLESS MARKED "W„ FOR WALL MOUNTED
<br />■ PRE -FINISHED POWER POLE PROVIDED AS PART OF FRONT END MODULAR SYSTEM
<br />PROVIDED AND INSTALLED BY ROSS FIXTURE VENDOR.
<br />17-77-7-771
<br />GYPSUM BOARD CEILING
<br />SUSPENDED ACOUSTICAL CEILING TILE
<br />Pro j. Mer.
<br />JU
<br />Job. Capt.
<br />SG
<br />Drawn by
<br />JT
<br />RON
<br />BARR,
<br />A.I.A.
<br />Revd by
<br />STATE
<br />OF FLORIDA
<br />I@S
<br />AR 0016160
<br />U
<br />W
<br />U
<br />H
<br />z
<br />O
<br />F-
<br />W
<br />>
<br />Q 2:
<br />n
<br />w
<br />W
<br />Iw-
<br />F=-- 2
<br />=
<br />U
<br />F-
<br />o❑~
<br />W
<br />'0'O
<br />2
<br />w
<br />4]
<br />0
<br />07
<br />-
<br />❑��
<br />-
<br />w
<br />OXa
<br />-
<br />U
<br />asOQ
<br />W
<br />❑
<br />KZzW
<br />MXO
<br />p
<br />WW°Oi
<br />¢ U=
<br />wz
<br />O
<br />� (
<br />w
<br />~
<br />a}v
<br />ZZzQ-ZOU
<br />F
<br />F
<br />0wo
<br />V''oo
<br />a
<br />�
<br />°WQ
<br />U
<br />=R0'
<br />oz
<br />XW
<br />01
<br />O
<br />(n
<br />d
<br />¢
<br />2
<br />o,
<br />U❑
<br />z=
<br />W
<br />a
<br />y
<br />z
<br />Wa
<br />(n
<br />w
<br />2
<br />w
<br />W
<br />Q
<br />2
<br />W
<br />o
<br />of
<br />=
<br />2
<br />m°
<br />oZ
<br />_
<br />o
<br />w
<br />2XXo
<br />Z
<br />F-
<br />Q d U
<br />W
<br />Z)
<br />Z
<br />�
<br />O
<br />F- Z
<br />o
<br />Z
<br />z
<br />O
<br />_
<br />? J
<br />°
<br />❑
<br />U W
<br />O tL F-
<br />°
<br />❑
<br />2
<br />W
<br />z O
<br />0 Z
<br />Z❑
<br />W
<br />Z U=
<br />z d W
<br />O
<br />F
<br />W w¢
<br />2
<br />2
<br />W W
<br />O
<br />2
<br />Z 0
<br />2
<br />F-
<br />a W a
<br />2
<br />r¢
<br />0
<br />�-
<br />o❑
<br />0
<br />o
<br />2 r
<br />Z?�
<br />0
<br />Q U
<br />©
<br />COPYRIGHT
<br />2012
<br />BARR ARCHITECTURAL STUDIO
<br />f
<br />V
<br />� w
<br />�f
<br />�
<br />nib
<br />f
<br />"'
<br />;I
<br />Y
<br />1
<br />I �
<br />PA �;
<br />I
<br />o
<br />V,.hL2�
<br />Revis Ions:
<br />CADFILE No.
<br />d'
<br />�
<br />M
<br />�
<br />M
<br />O
<br />�
<br />H
<br />1
<br />f�
<br />f
<br />�^ f�
<br />h�
<br />O
<br />�
<br />N
<br />Sheet Title
<br />LIGHTING
<br />PLAN
<br />sca le:
<br />Date:
<br />Z.J.
<br />Sheet No.
<br />BUCHANAN P.E. CONSULTING INC"
<br />--
<br />AL
<br />A A B ANA
<br />ELECTRICAL * MECHANICAL * PLUMBING
<br />Project No.
<br />ENGINEERING
<br />6191 W. ATLANTIC BLVD., SUITE #2
<br />`#
<br />E3-0
<br />MARGATE, FL 33063
<br />Ph: 954-590-3300 Fax: 954-590-2232
<br />Email: mepengineers@aol.com
<br />RAJA BUCHANAN FL P.E # 48916
<br />CERTIFICATE OF AUTHORIZATION # 8842
<br />MAY 0 5 201412-027
<br />DATE:
<br />3 OF 3
<br />--------r---------------- -
<br />-----�:.f.,,-r-----r-rrfr�-----i--r-- --r- -
<br />
|